Takara Belmont DIVAN-Z AB-DVZF User manual

1. Move the chair to the installation location.
●Move the chair by holding the skid.
(Carrying the chair by the upper part is
dangerous because the base could come off
and drop.)
Be sure to store this manual in a secure location together with the operation manual as it describes items
that must be understood by the customer.
●When the chair is still on the skid, move the
chair to the edge of the skid as shown in the
figure on the right, tilt the chair and skid,
and pull out the skid. Removing the skid
without tilting it can result in the skid
interfering with the mechanisms on the
underside of the base, causing an abnormal
noise to be emitted when the chair is rotated.
●After unloading the product from the skid,
moving the chair by holding the metal plate
under the foot switch and the body (lower
half).
2023-04 (1st edition)
Installation Procedures
BOOK No.1E09JYAEBOOK No.1E09JYAE
Installation Manual
1
Body
(lower half)
Foot switch
•Hold the base, foot switch, or the body (lower
half) when performing procedures such as
transporting, installing the rubber ring to, or
positioning the chair. (Do not hold the natural
wood parts.) When holding the chair, be
careful not to damage the cape holders, wrinkle
or dirty the leather, and that the base does not
come off.
•If you need to hold the upper half of the body or
the backrest it in a tilted position, take care not
to apply force.
•Make sure not to apply excessive force that
could damage the chair even when holding by
the parts shown in the figure on the right.
•Do not push the backrest from behind. This may
cause malfunction.
Backrest
Body
(upper half)
Body
(lower half)
Base
Foot switch
CAUTION
Hold the skid when
carrying the chair.
Takara Belmont Barber Chair
Model No. AB-DVZF

3. Connect the power plug to the outlet with ground terminal.
2. Attach the rubber ring to the base.
Determine the installation location. Lift the base off the floor and attach the rubber ring to the rim of
the base.
●It is easier to attach the rubber ring by lifting up one side of the chair at a time. Hold the body and
shoulder part of the backrest to balance the force, and tilt the chair body to attach the rubber ring one
side at a time. Do not apply excessive force to the armrest or other parts, or strike it from above
when tilting the chair body.
4. Check that the chair operates normally.
Turn the power on and check that the chair raises/lowers normally, the backrest raises/reclines
normally, the legrest raises/lowers normally, and the rotation lock/release, preset function, and
auto-return function operate normally.
The chair must absolutely be grounded in order to prevent electric shock.
Be sure to ground the chair to prevent accident due to current leakage and to improve the
noise-dampening performance of the control circuit.
Takara Belmont has no responsibility for any current leakage that results if the above-indicated
procedures are not performed.
2
During installation, ensure that the power cord outlet of the chair base is aligned with the chair front.
Failure to follow this instruction may cause damage to the power cord.
*Make sure that the power cord is positioned in the center of the hole of the footrest mounting guide.
A hole of the footrest
mounting guide
Legrest
Base
To prevent damage to the floor by the chair base, put a protective covering on the floor before working.

5. Install the footrest.
3
Install the footrestInstall the footrest
Adjusting the adjuster height
①Insert the footrest bracket into the hole of the footrest mount.
②Slide the footrest bracket to the back until it hits the stoppers.
③Lower the footrest.
④Make sure the footrest is level.
① ③
Footrest mount
Footrest bracket
②
Positioning stoppers
• After installing the footrest, make sure that the footrest bracket is firmly hooked to
the footrest mount and that the footrest is kept level. Failure to do so may result in
injury.
• Be careful when lifting and carrying the footrest, and of where you place it because
the footrest is heavy. Dropping the footrest could result in injury or damage the floor.
When adjusting the height of the adjuster, make sure that the adjuster does not rub on
the floor or catch the power cord when the chair is rotated. On the contrary, adjust the
height so that the product does not fall over even if the customer gets on the footrest at
exit/entry position.
The adjuster, which prevents the chair from tipping over, is located on the underside of the footrest.
Adjusting the adjuster height
①Loosen the adjuster nut with wrench (opposite side
17mm) by turning it counterclockwise.
②Adjust the height by rotating the adjuster.
counterclockwise➡highten clockwise➡shorten
③Fasten the adjuster nut with wrench (opposite side
17mm) by turning it clockwise.
Adjuster nut
Shorten Highten
Adjuster
CAUTION
WARNING

4
Adjusting Preset PositionsAdjusting Preset Positions
Although the settings positions of the preset switches are previously set when shipped from the factory, you
can change the settings to positions that match your customers.
Refer to "Adjusting preset positions" on p. 23 of the DIVAN-Z Operation Manual, and change the settings.
Usage environmentUsage environment
Temperature 0 〜40ºC
Humidity 10 〜95% (No condensation)
Air pressure 700 〜1060 hPa
Transportation / Storage environmentTransportation / Storage environment
Temperature -20 〜70ºC
Humidity 10 〜95% (No condensation)
Air pressure 700 〜1060 hPa