Takara Belmont Salon Console User manual

2017.05
Contents
Before installation
Usage conditions
Parts illustration
Content of packaging
Installation
MEMO
2
4
5
5
6
11
SALON CONSOLE
Installation Instructions
To the customers
• Customers must not install Salon Console by
themselves.
• Customers must store this instruction in
a safe place so as not to lose them.
To the installer
• The instructions should be thoroughly read and
understood before installation to ensure that
Salon Console is installed correctly.
• After installation, give this instruction to the
customer.
* The actual shape of Salon Console and the images
and dimensions listed in this instruction may be
modified and are subject to change without notice.
If Salon Console is installed after ignoring this symbol, "there is the risk of light or moderate injury or physical
damage".
The precautions listed here are to ensure that Salon Console can be installed safely, and to prevent any
danger or risk to the person installing Salon Console or those around them. All of these precautions are
important for safety. If Salon Console is installed without adhering to the precautions, Takara Belmont is
not responsible for any damage or risk of accidents to the person who installs or the others around them.
Caution
Version 4
1
■Salon Console
AY-CU*SX1[single tap type]
AY-CU*SX2[double tap type]

2
Before installation
Custom type S size , L size
(unit : mm)
■Front view ■side view
■Front view ■side view
Custom type LL size
<Dimensions> Wall fixing
position
Wall fixing position
291
800800 650
800 1450
10 10
Platform 1200Platform 1450
Platform 380
800
400 400
756
315
280
22.5
921 (951)
90
770 31
Neck tip 717 24 min. Base
W.L.
291
800800
800
10 10Platform 1200Platform 1300
Platform 380
800
400 400
S size 400
L size 500
S size 1200 , L size 1300
F.L.
F.L.
756
315
280
22.5
921 (951)
90
120
(150) 770 31
Neck height 770 (800)
Basin unit fixing position 895 (925)
Custom type side unit fixing position 850 (880)
Neck height 770 (800)
Neck tip 719 24 min. Base
Basin unit fixing position 895 (925)
Custom type side unit fixing position 850 (880)
W.L.
120
(150)
*( ) shows the platform height of 150mm.
<Plumbing layout>
105
W.L. W.L.
800
80(Cold water supply) 40 75
256 10
Elbow VP40
Elbow 1/2" Cheese VP40
Cheese 1/2" Cold water supply floor pipe 1/2"
Hot water supply floor pipe 1/2"
Drain floor pipe VU40
Bowl center
Chair center
F.L. F.L. F.L.
W.L.
Drain VU40
H120 (H150)
Hot water supply 1/2"
H100 (H130)
Cold water supply 1/2"
H100 (H130)
F.L. F.L.
107 (137)
W.L.
Drain VU40
H120 (H150)
Hot water supply 1/2"
H100 (H130)
Cold water supply 1/2"
H100 (H130)
110(Hot water supply)
170(Drain)
80(Cold water supply)
110(Hot water supply)
170(Drain)
S size 1200, L size 1300, LL size 1450
Bowl center
Chair center

3
[Pipe specifications]
Ensure that the material or finishing of the floor surface is waterproof or has a waterproof coating applied.
Always ensure that the floor surface is horizontally level.
Ensure that the floor surface is smooth and free from bumps around the attachment areas.
Installing pipes
The following levels of strength are required for the floor surface.
Floor surface
For installation on the wall, the wall base strength should be equal to or stronger than a 12mm-thick
composite panel. If the wall is made of plaster or its thickness is less than 12mm, add a wooden
reinforcement onto the wall(See page 2).
Use a waterproof material such as melamine for the wall surface (for possible water splashes during
shampoo treatment).
Wall
In case of the installation on the first floor of higher,waterproof the floor appropriately
(e.g. do water proofing work, use a floor tray made of stainless steel, set up a water leak sensor, etc.)
Waterproofing
Drainage
Rc 1 / 2“ pipe from floor Hotwater supply H : 110mm
water supply H : 80mm
VU40 Pipe from floor H : 170mm
Hot water supply, water supply
Wooden floor
Mortar floor Mortar thickness of 50 mm or more
Special floor (stone finish)
A foundation with levels of strength listed above around the installation areas is required.
Plywood thickness of 30 mm or more (two 15 mm sheets joined together)
Installation of pipes
The following are important points to adhere to during the installation of pipes.
Read through the details carefully and ensure that the pipes are installed correctly.
When installing this product, ensure that installation of pipes adheres to the instructions outlined in "Precautions
during installation of pipes". Installing pipes without reading through the precautions will mean water may not mix
properly, and a set temperature will not be achieved.
This product is designed for indoor installation. Always install this product indoors.

4
Precautions during installation of pipes
Do not use pipes made of materials that may introduce rust for the water supply pipe.
In general, VP pipes or other materials specified by regulations in that particular region, are recommended for
installation.
In general, Type L deoxidized copper pipes are recommended for hot water pipes.
In general, the same diameter and same pressure is recommended for hot water pipes and water supply pipes.
Always use a reamer to deburr the ends of cut pipes.
Avoid using inverted U-shaped pipes (siphon) as these can cause air to become trapped.
Always connect hot water pipes and water supply pipes after removing all contaminants such as dirt, sand and oil
as these can cause problems.
After connecting the pipes and testing water flow, clean the filter and shower head.
Ensure that the drain pipe is installed at a gradient of 1/50 for a diameter of φ75 or less, or 1/100 for a diameter of
φ75 or more.
Do not connect the hot water pipes and water supply pipes in reverse.
Connecting pipes in reverse will mean the temperature of water cannot be controlled properly by the water taps,
which can cause problems including burns.
Ensure that the hot water pipes from water boilers are only run over a short distance so as to minimize resistance.
Longer pipes can cause fluctuations in temperature and poor hot water delivery.
Always wrap pipes with lagging material after installation is complete.
Water boiler pipes
In general, the same diameter and same pressure is recommended for main hot water pipes and main water
supply pipes.
Equipment comes with hair catchers installed.
Hot water supply and water supply conditions
Water used
Hot water supply,
water supply pressure
Hot water temperature
into the product
Water boiler
Public water supply (do not use non-drinkable well water or water that contains rust or sand.)
If the water hardness is 80 ppm or higher, install a water softener to prevent the buildup of
scale within the basin body. Aeration may be minimal when using shampoo even if drinkable
well water is used, so a water softener should be installed.
Use a pressure set between 0.1 to 0.4 MPa (1 to 4 kgf/cm2). If multiple Salon Console are used,
ensure that the pressure does not drop below 0.1 MPa (1 kgf/cm2).
Set the water supply pressure ≧hot water supply pressure.
Set the difference between the hot water supply pressure and water supply pressure to within
0.2 MPa (2 kgf/cm2).
 Set the hot water temperature to 80˚C or less.
 Set the temperature 10˚C or higher than the shower temperature used.
Do not use steam with the hot water supply.
Usage conditions

Platform
Maintenance door Joint bracket
Counter
Cold water supply pipe
Hot water supply pipe
Basin body
Wall fixing bracket
Water stop valve
Flexible pipe
Basin
Side unit left
Parts Illustration
Content of packaging
□Flexible pipe …2 □Water stop valve …2
( L=200 mm )
□Basin body floor fixing
screw set
□Bottle nozzle …3
□Shampoo bottle …3 □Nozzle packing …3
□Installation manual (this document) …1
□Instruction manual…1
5
Side unit right

6
Installation
①Place the platforms and connect them by joint bracket.
②Set a level gauge as shown in the illustration. Adjust the adjuster
bolts and level the platforms.
Precaution before installation
1Setting platform
Hot water / water supply pipe, Drain pipe
Install the pipes of cold water supply, hot water supply and drain correctly referring to the dimensions and the
plumbing layout.
Wall
If the wall material is plaster board (fire prevention board, add a wooden reinforcement (12mm-thick composite panel
[see page 2] )
Tappingscrew
Tappingscrew
Level gaude
This face needs to
be horizonal
Joint bracket
Platform
Adjuster bolt
①Place the basin body on the platform while aligning the
center of the basin body with the center and between
basin body fixing screw hole.
②Press the basin body to the plate of the platform.
③Secure the basin body to the platform with supplied
wood screw into basin body fixing screw hole.
[M4×16 Tapping screw…2]
Setting basin body
2
Basin body
Platform
Center of basin body
（center guide hole）
Basin body fixing
screw hole
Plate
Installing location
When installing the custom type to the wall, ①keep clearance of at least 30 mm; or ②install KF-SCWS Salon Console
Wall Spacer between the unit and the wall (regardless that the wall is in the left corner or the right corner).
NG OK
The door hits the wall.
Side
unit
Basin body Side
unit
W.L.
W.L.
The door opens to
the end.
Basin body
W.L.
W.L.
※The illustration above shows when installed at the right corner. (Same as when installed at the left corner.)
※Keep clearance of at least
30 mm, or install
KF-SCWS Salon Console
Wall Spacer.

7
⑤Secure the basin body to the wall with the wall fixing
brackets (2 points).
[M4×30 Wood screw....2]
Wall fixing
bracket
ⅱ)
Wood screw
Wood screw
Always test the drainage flow to prevent accident during operation.
* Test the drainage flow at the sametime of the water flow. (P9 3-⑤)
④Connect the drain hose with installed drain pipe.
i ) Insert the drain hose with a bearing sleeve to the drain pipe.
ii) Press the bearing sleeve to the drain pipe and fit it into
the drain pipe so that the drain hose and the drain pipe
are connected tightly.
i ) Loosen the screws of the wall fixing brackets in the basin
body side first. Set and tighten the wood screws in the
wall.
ii) Adjust the position of the basin body so that stand
vertical on the floor. And then tighten the screws in
the basin body.
* When the diameter of the drain pipe is VU50, use an
adjuster.
*The joint of the bearing sleeve and the drain pipe must
be set or installed airtight in order to prevent water leakage.
Bearing sleeve
Adjuster
*Used for
VU50 pipe only
VU40
VU40,VU50
Drain hose
The joint must
be airtight
Drain hose
Bearing sleeve
Installed drain pipe
Caution

8
* When you fix the basin body on the wall with no gap
and inclined wall, the basin body will be fixed improperly.
The gap between basin and basin body will vary.
* You can adjust it because of long hole
* If there is gap between the basin body and the wall,
fix the basin body on the wall keeping gap.
Wall fixing bracket
gap
gap
no gap
no gap

9
* Test the water flow and inspect the following items. The hot water may be slightly tainted at the start of
the water flow test, however this does not indicate any problem.
ⅰ) Is there no water leaking from the pipe joints?
The pipe joints may come loose during transportation, so check all the joints in the basin body.
ⅱ) Are the hot water supply and water supply pressures at the same, stable pressure?
ⅲ)Is temperature be controlled properly?
ⅳ) Check that the shower outlet flow is sufficient, by the following as a guide for flow rate.
①Install water stop valve to installed hot water / water supply.
*Mount the water stop valve as the picture below and it is easy to open and close water with knob.
(Knob should be toward outside.)
②Attach flexible pipes to check valves.
*Don’t connect the hot water and water in reverse.
*Make sure to use the provided packings.
③Attach flexible pipes to water stop valves.
*Make sure to use the provided packings.
(Single tap type) (double tap type)
④Test water flow
⑤Conduct water drain test. Check there is no leakage from the joint of the drain hose.
3Connecting hot water and water supply pipe
Water stop valve[R1/2×G1/2]
Installed hot water
/ water supply pipe
Packing
Packing
Flexible pipe[L=200]
Check valve
Packing
Packing
Flexible pipe[L=200]
Hot waterWater
Check valve
Caution
Caution
Test the water flow before use to prevent accidents.
Drain test must be conducted in order to prevent water leakage during operation.
Installed hot water
/ water supply pipe
Hot water
Water
Hot waterWater
Hot water
Water
Water stop valve[R1/2×G1/2]
Hot water supply pressure, water supply pressure : 0.1 MPa each
Shower outlet temperature : 40˚C
Shower head : Approximately 8 L/min

10
■Inspection
○Check that there are no missing screws or other parts.
6After installation
○Check that the basin body can be opened and closed smoothly.
○Check that the basin body and the side unit are
installed without big gap.
① Place the side unit on the platform.
② Press the side unit on the plates.
③ Push the side unit to the basin body.
④ Fix the side unit to the basin body.
⑤ Fix the side unit to the wall.
4Setting side unit
Attach the counter to the basin body.
[M4×16 wood screw...3]
Follow the provided install manual in counter box about assembling counter.
5Setting counter
Basin body
Wood screw
Counter
Platform
plate
①Placing on the platform
②Pressing to the plate
③Pushing to the basin body.
④Fixing to the basin unit.
⑤Fixing to the
wall.
Wood screw
for wall
Wood screw for
basin body
Side unit
Caution
Be sure to execute the inspection before use to prevent accidents.