Takara Belmont Yume DX User manual

Thank you for purchasing our Takara Belmont YUME DX.
The instructions contained in this booklet should be thoroughly read and under-
stood before operating the shampoo unit.
This product is intended for the exclusive use for hairdressing & barber salons,
and must not be used for other purpose.
Keep manual in a place where it can be easily referred to when necessary.
YUME DX
Operating Instructions
Thank you for purchasing our product.
Please read through this manual and this note carefully before installing or using.
These instructions provide important information for correct usage of the product
to avoid personal injuries or property damages against you or your clients.
This product is intended for the exclusive use in hair salon or esthetic salon
for their treatment and service, and must be operated or handled by the
qualified/professional hairdressers or by their staff under the supervision of hairdressers.
2019.02
Version5
1A0FTXA0

TAB L E OF C ONT E NT S
1. L ocations of Warning L abels ........................ 1
2. Dimension and Specifications....................... 2
3. Overall View and Major Components........... 3
4. Accessories.................................................... 4
5. Preparation .................................................... 4
6. Operating Instruction..................................... 5
7. Maintenance.................................................. 8
8. Troubleshooting............................................. 10
9. Consumable Parts.......................................... 10

ＣＡＵＴＩＯＮ
Drain Outlet Drain Cap
The drain cap must be detached
from the drain outlet when the
product is not in use.
1.Locations of W arning Labels
Be careful not to pinch
a hand and etc.
Be careful not to pinch
a hand and etc.
-1-

2. Dimension and S pecifications
Type ------------------------------ EX -Y M2NL , EX -Y M2NR, SU-Y M2
Drive System -------------------- Motorized Hydraulic System
Measurement -------------------- 760 x 2000 x 990 mm (W x L x H)
A ngle of B ackrest ---------------- 67° (8° 75°)
Type of Mixing ------------------ T hermo Mixing
Stop Valve ------------------------ Water x 1 (Handle Type) / Hot Water x 1 (Handle Type)
E lectrical R equirements -------- 230V 50Hz 1.7A (appliance itself)(CE Spec,)
Usage E nvironment ------------ Operational Temperature (10 40°C)
Water and Hot Water ---------- 0.08 0.6Mpa (0.8 6kgf/)
Supply Pressure ---------------- Water Supply Pressure Hot Water Supply Pressure
Pressure difference between water supply and hot water supply within 0.2Mpa (2kgf.)
Water Volume (Shower Head) ---- 10L /min (water and hot water pressure are 0.1 Mpa)
Weight --------------------------- 205 kg
-2-
650
520
≧
cm2
～
～
～
～ cm2
520
2000
760
845
505
610
950
990
8°
E lectrical R equirements -------- 220V 50Hz 1.7A

3. Overall View and Major C omponents
-3-
B ackres t
Headres t
S hower head
S hampoo basin
S eat
Legres t
Legres t lever
Main power switch
S ervice outlet
Maintenance cover
Headres t handle
Headres t bar socket
Neck cus hion
(C ons umable) Head pillow
(C ons umable)
Temperature control knob
S hower head
S hower hose
Tap
F loor s heet
■Foot Switch
E X-Y M2NLA : Left side foot switch E X-Y M2NR A : R ight side foot s witch ■Leg-res t Lever
UP DOWN
(E X-Y M2NLA and
E X -Y M2NR A only)
UP
DOWN
UP
DOWN
P reset S hampoo
position B ackres t
return
P reset S hampoo
position B ackres t
return
B ackres t
reclining
B ackres t
raising
Auto R eturn S eat rotation lock Auto R eturn S eat rotation lock
B ackres t
reclining B ackres t
raising
■Main Body
A sticker of drain hose replacement
Hose replacement (1 )
Service History
Month Year
Month Year
Month Year
Month YearHose replacement (3 )
Hose replacement (2 )
ST
ND
RD
Original Installation date
Drain cap

4. Accessories
Operation Manual ...1
Installation instructions ...1
YUME SPA Technical Manual ...1
Neck Cushion ....1 Head Pillow ...1set
Drain Cap ...1 Hair Catcher ...1
Noise Reduction Tape ...1
Anti-water dropping device ...1
5. Preparation
5-1. Attach the Neck Cushion
1. Attach the neck cushion on metal ttings
as shown in gure.
2. Both side hooks of the neck cushion is xed on a xed pin.
5-2. Attach the Head Pillow
1. Attach the head pillow as shown in gure.
-4-
Hook Neck Cushion
Fixed Pin Metal Fitting
Hook
Hook
Head Pillow

6. Operating Instruction
-5-
6-1 Main Switch
Main switch is located on the left side of the pump cover (E X -Y M2NL )
or on the right side (E X -Y M2NR ).
OF F
Turn off the main switch after daily operation
Operate the main switch by hand only.
In the event of extremely low oil temperature,
“warm-up” mode may start.
6-2 Controls
B efore operating the chair, confirm that it is safe for the patient
and the operator.
(1) Manual Mode Control
A. Seat L ifting
K eep depressing UP button until the seat is lifted up to the
desired position.
B . Seat L owering
K eep depressing DOWN button until the seat is lowered to the
desired position.
C. B ackrest R eclining
K eep depressing B ackrest reclining button until the backrest is
reclined to the desired position.
D. B ackrest R aising
K eep depressing B ackrest raising button until the backrest is
raised to the desired position.
C aution
E . L egrest R aising (E X -Y M2NL A and E X -Y M 2NR A only)
Move leg-rest lever to the left/right side for up-and-down.
F. Seat R otating
Make sure to raise the backrest by depressing P2 button
rotating the seat. Momentarily press L P button (L ock button)
releases the safety seat lock.
*T he lock is not released when backrest angle is less than 30°.
R otating the seat slowly by holoding the backrest.
Press L P button again to lock the seat at desired position.
<Warm-up mode>
Warm-up operation goes on at the extremely low oil tempera-
ture. It beeps for 3 minutes until this mode completes.
ON
UP
DOWN
DOWNUP
B ack res t
reclining
S eat rotation lock
B ack res t rais ing

(2) Auto Mode Control
G. Preset Control
Press P1 button a little longer (for around half second),
the seat will move to the preset shampoo postion automatically.
(If adjustment is needed, please refer A UTO MODE
POSIT ION ADJUST ME NT.)
H. A uto R eturn
Press P2 button a bit longer (for around half second) puts
the backrest upright position automatically.
Press A uto R eturn button for around half second, the seat will return
to the initial position.
* Initial position : seat - lowest point , backrest - upright position
I. E mergency Stop
During automatic procedure (Preset and Auto return), depress of any
side of the buttons on the foot control will cancel the automatic
movement immediately.
6-3 A uto Mode Position Adjustment
Preset position adjustment
A. Set the seat and the backrest to the desired preset position by manual control.
B . Turn off main switch.
C. While depressing P1 button, turn on main switch.
D. K eep depressing P1 button until buzzer sounds, then release it.
-6-
6-4. SA FE T Y L OC K DE V I C E
Chair down movements can be stopped automatically
by the safety lock device when pressure is detected
between the base and the safety lock cover.
If the safety device has been activated, simply operate
the base up button and remove the object causing the
safety device to activate from this area.
S afety lock cover
B as e
P res et S hampoo pos ition B ackres t return
Auto R eturn

R otate the drain cap in the clockwise
direction to close the drain outlet.
To drain the accumulated water, rotate the
drain cap in the counterclockwise direction
to open the drain outlet.
The lid is clos ed. The lid is open.
C lockwise Direction
C ounterclockwise Direction
<Accumulating the Water> <Discharging the Water>
The drain cap must be detached from the drain outlet when
the product is not in use. If the lid is not detached, the lid
may accidentally close, and the water may overflow the
basin from the failure to notice water discharge, thus resulting
in water leaks.
6-6
Drain C ap
C aution
Accumulating Hot Water
Drain C ap
6-5 A djustment the Water / Hot Water
A. Turn the tap to counter clockwise.
B . Adjust the water temperature with
temperature control knob.
C. Press stop button on the temperature
control knob to release lock for hot water,
then turn clockwise.
S top
S top
B utton
(H) Hot
(C ) C old
Tap
Temperature
C ontrol K nob
S hower Head
Open
Hot
C old
6-7 How to use Headrest (SU-Y M2AM and SU-Y M2BM only)
Headrest can be utilized in facial treatment and massage.
Set the backrest position to attach the headrest properly.
Attach the headrest bar to the end tightly.
6-8 How to use Service Outlet
The unit is equipped with a service outlet on the left/right
side of the pump cover.
Capacity : Up to 1,500W (the main unit is not in use)
Up to 900W (the main unit is in use)
Usage in excess of the maximum capacity switches off the main unit.
-7-

7-2. Neck cushion and head pillow(consumable parts)
Use dry cloth to wipe off water and dry in shade.
Dump cloth with neutral detergent and wipe to remove coloring or perm solution.
7-1. Hair Catcher
Take out the hair catcher under the drain cap and remove hairs
from the hair catcher.
Drain C ap
Hair C atcher
Alcohol
Notice
Do not use the following substances.
Thinner, alcohol, gasoline, kerosene or other volatile chemicals; waxes containing abrasives;
sponges containing abrasives, etc.
Thinner
G as oline
Waxes
C ontaining
abras ives
C hemicals
7-3. Use dry and soft cloth to clean upholstery, plastics, plated and painted surface.
Dump cloth with neutral detergent and wipe to remove stubborn stains and dirt. Use only mild
neutral detergent. Use cotton buds etc. to clean around the neck cushion and head pillow
mounting parts.
7-4. Drain cap
Wash around the drain cap, and remove any hair
or dirt from solvents.
The drain cap is a consumable supply.
If it is extremely dirty, remove the packing from
the drain cap, wash with detergent solution diluted
using water, and rinse carefully with water.
Drain C ap
Drain C ap G as ket
C aution
Clean the hair catcher as often as possible. If using the hair catcher not
cleaned, it may cause clogging of the port, overflow or poor sanitary.
Cleaning the hair catcher every after each shampooing is recommended.
R inse the cushion immediately after chemical is splashed on the neck cushion.
Splashed chemical may cause deterioration or discoloration.
C aution
Wipe the bowl with diluted neutral detergent.
Do NOT use metal scrub brushes, paper files. Using them may be a cause of scars.
C aution
7-5. Cleaning of bowl
7. Maintenance
-8-

7-6. Strainer for check valve
Clean strainer (built-in check valve) at regular intervals.
R emove the water in strainer if freezing is expected in the cold district.
A. R aise the chair and turn off the main switch.
B . R emove 2 screws and open the maintenance cover
C. Place cloths near the water / hot water supplise.
D. Turn off the water & hot water stop valves and
remove strainer by flat head screw driver and
wipe off the water by cloth.
E . After cleaning the strainer, put it back and tighten up.
F. Wipe water off and remove cloth.
G. Turn on the water & hot water stop valves.
H. Close the maintenance cover and install 2 screws.
Maintenance
C over
S crew
Water
Hot Water
Water & Hot Water S top Valve
C heck Valve
(C lose)
F lat Head
S crew Driver
S trainer
C loth
(Open)
Water & Hot Water S top Valve
Open the maintenance cover and check water leakage
once a week.
Water leak check
-9-

Symptom Check
Seat and backrest
Check the fuses in your fuse box to make sure they haven’ t burned out.
After the long time operation, Over temperature protection system
works. Please leave the chair for 10 minutes and start operation.
Unplug the machine and then plug it in again and see if it will operate.
In case other than those listed above, contact our service center or sales office.
• Neck cushion • Head pillows • Drain cap • Anti-water dropping device
doesn't move Make sure that the main switch has been turned on.
Make sure that the power plug is properly plugged into the outlet.
If you have a breaker box, check for tripped breakers.
Main S witch
ON?
F us e B ox or B reaker
No W ater / Hot Water Make sure that the water & hot water stop valve has been turned on.
The temperature of
hot water is too low
Check to make sure that the temperature setting of water supply tank
is properly.
Make sure that the temperature setting of the chair is properly.
Slow drainage Check to make sure that the hair removed from the hair catcher
completely.
C AUT ION
If the supply cord is damaged, it must be replaces by
the manufacturer or its service agent or similarly
quali-ed person in order to avoid hazard.
8. Troubleshooting
9. C onsumable P arts
-10-

NOTE
Caution
Be careful of use.
The appliance is not to be used by children or persons
with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have
been given supervision or instruction.
Be careful of use.
Children shall not play with the appliance.
Be careful of use.
Cleaning and user maintenance shall not be made by
children without supervision.
2-1-1, Higashishinsaibashi, Chuo-ku, Osaka, 542-0083, Japan
TEL:[phone]
FAX:[phone]
TAKARA BELMONT CORPORATION
MANUFACTURER
TAKARA COMPANY EUROPE GmbH
Berner Strasse 18, 60437
Frankfurt am Main, Germany
TEL: [phone]
FAX: [phone]
EU REPRESENTATIVE