Takara Belmont YUME User manual

BEGB10D0
2020.07
SHAMPOO UNIT
YUME
This manual provides information and instructions for YUME SHAMPOO
UNIT. The instructions contained in this booklet should be thoroughly read
and understood before attempting to install the equipment.
After the installation is completed, le this manual and refer back to it
for future maintenance.
IMPORTANT
INSTALLATION
INSTRUCTIONS
Version 6

TABLE OF CONTENTS
INST ALLA TION INSTRUCTIONS
1. Overall View and Major Components........... 1
2. Dimension & Specifications.......................... 2
3. Plumbing Layout........................................... 3
4. Contents of Unpacked Products.................... 4
5. Installation Instruction................................... 5
5-1. Preparations for Installations
...................... 5
5-2. Installation of the Carriage Jig
.................... 5
5-3. Marking for unit fixing position
.................. 6
5-4. Fix the Moistureproof sheet and packing
..... 6
5-5. Installation of unit
.......................................... 6
5-6. Drain Pipe Connection .................................... 8
5-7.
Water and HotWater Supply Line Connection
.... 8
5-8. Unit Power Supply Line ................................... 9
5-9. Installation of Base Cover ................................ 9
5-10. Attach the backrest and seat cushion............. 10
5-11. Attach the Neck Cushion................................ 11
5-12. Attach the Head Pillow.................................. 11

■Main Body Backrest
Seat
Main switch
Shampoo basin
Maintenance cover Foot switch
Neck cushion
(Consumable)
Head pillow
(Consumable)
Shower head
Tap
Shower hose
Preset
DOWN
UPAuto Return
Backrest Raising Backrest Reclining
DOWN
UPAuto Return
Backrest Reclining Backrest Raising
Temperature control knob
Body cover
EX-YMNL : left side foot switch EX-YMNR : right side foot switch
Preset
Noise reduction tape
(inside cover)
Safety lock cover
1. Overall View and Major Components
-1-
■Foot Switch
A sticker of drain hose replacement
Hose replacement (1 )
Service History
Month Year
Month Year
Month Year
Month YearHose replacement (3 )
Hose replacement (2 )
ST
ND
RD
Original Installation date
Drain cap

2. Dimension & Specications
-2-
6°
65°
760
595
75
28 35
650
520
950
600
975
450 170
Min.630(Sitting Position)
Min.430(Standing Position )
465 531037
Line for Edge of Base Plate
Drain Pipe
170
Min.215
1965
Min.2980(Sitting Position) / Min.2780(Standing Position)
880 1270
600 (Base Plate)
830
480
520
Wall
75
Water Supply
Hot Water Supply
Wall
Center of Drain Pipe
Type ------------------------------ EX-YMNL, EX-YMNR, SU-YM
Drive System -------------------- Motorized Hydraulic System
Measurement -------------------- 760 x 1985 x 975 mm (W x L x H)
Angle of Bracket ---------------- 59°(6°
65
)
Type of Mixing ------------------ Thermo Mixing
StopValve ------------------------ Water x 1 (HandleType) / HotWater x 1 (Handle Type)
Electrical Requirements-------- AC 110・120V
50/60 Hz 5.8/4.4A
Usage Environment ------------ OperationalTemperature (1040℃ )
Water and HotWater ---------- 0.08 0.6Mpa (0.8 6kgf/)
Supply Pressure ---------------- Water Supply Pressure
 Hot Water Supply Pressure
Pressure difference between water supply and hot water supply within0.2Mpa (2kgf.)
WaterVolume (Shower Head) ---- 10L /min (water and hot water pressure are 0.1 Mpa)
Weight --------------------------- 156 kg
≧
cm
2
cm
2
～
～～
～
Electrical Requirements-------- AC 240V 50/60 Hz 2.3/2.3A
Electrical Requirements-------- AC 220V 50/60 Hz 2.1/2.5A
Electrical Requirements-------- AC 230V 50/60 Hz 2.1/2.4A
Electrical Requirements-------- AC 230V 50/60 Hz 2.1/2.4A(CE Spec, )

Bolt (anchor) fixed position
210
420
215
430
200 Moistureproof Packin g
5
15
160 Space of Plumbing
32
143
105 455
65
75
135
600 Base Plat e
300
Power Source
Cable should have 1000mm
Water 1/2” 13m/m(Height 50mm)
Hot Water 1/2” 13m/m(Height 50mm)
28
75 35
80
480 Base Plat e
225 Space of Plumbing
265 Moistureproof Packin g
195
2095
Center to Wall or Center to Cabinet Min.1000mm Including customer
approach spac e
Min.800mm
115
100
160
50 15
Seat Side Bowl Side
From Wall or Cabine t
Min.1080mm
From Wall or Cabine t
Min.1900mm : Sitting Position Min.1700mm : Standing Position
Edge of Base Plat e
Bolt (anchor) fixed position
Bolt (anchor) fixed position Bolt (anchor) fixed position
Drain VU40 (Height 60mm)
Excluding customer
approach spac e
Connected position of power plug and power suppl y outlet (Recommendation)
3. Plumbing Layout
-3-

・ Neck Cushion ・ Head Pillow ・ Drain Cap ・ Hair Catcher
・ Floor Bolts
M8×70 Anchor Bolt x4
M8×65 Hex Head Tap Bolt x4
Flat Washer ×4
・ Moistureproof
Sheet
・ Moistureproof
Packing (Sponge)
・ Water Stop
Valve
・ Flexible Pipe
・ Drain Hose Packing
・ Operation Manual
・ Installation instructions
・ YUME SPA Technical Manual(except for China)
・ Drain Hose Clamp
・ Noise Reduction Tape
4. Contents of Unpacked Product
•YUME Main Body
•Seat and Backrest set
• Jig A
• Jig B Bracket
• Jig B
• Jig B Support Bar
Screws
•Carriage Jig 【OPTION】
-4-
 ※Elbow and drain pipe(VU40) are NOT INCLUDED with shipment. Please prepare it beforehand.
・Seat Cushion ・Seat Cover(R) ・Seat Cover(L)
・Backrest Cushion ・Backrest Cover
・Screws

-5-
5. Installation Instruction
1. Unpacking
Remove nails from lower part of wooden crate.
Lift up the upper portion of wooden crate.
Chair will be left on the skid.
2. Remove the pump cover.
1. Remove the screws and remove maintenance cover,
base cover left and right from main body.
2. Remove the oil plug with red tag from oil reservoir.
3. Plug the unit power supply plug in to the
suitable power supply outlet.
4. Turn on the main switch located on the left side
of base.
5. Keep depressing UP button of foot switch
until the seat is lifted up to the end.
6. Turn off the main switch.
7. Unplug the unit power plug from power supply outlet.

5-1. Preparations for Installations
Nails
Nails
Oil Plug with Red Tag
Maintenance Cover
Base Cover(R)
Base Cover(R)
Oil Reservoi r
Main Switch
Foot Switch
Note : Do not remove the unit from the pallet
until the unit xing position is ready.
Holding the Carriage Jig and place it at
planned location. Do not carry by holding
the body or basin.
5-2. Installation of the Carriage Jig
1. Fix the Jig A to the base.(M10 x 30)
2. Fix the Jig B bracket to the base.(M10 x 50)
3. Attach the Jig B support bar to the
Jig B bracket.
4. Attach the Jig B to the Jig B support bar
and tighten the nuts.(M16)
CAUTION
Do not turn on power during installation.
Base
1 Jig A 2 Jig B Bracket
4 Jig B
3 Jig B Support Bar
Screws
M10 x 30
Screws
M10 x 50

Moistureproof Sheet
Moistureproof
Packing
Moistureproof Packin g
Seal a space
around here
5-4. Fix the Moistureproof sheet and packing
Please obtain the moistureproof sheet and the moistureproof packing to prevent from the
main body damaged by the moisture. Deterioration and the breakdown of structural parts
and electrical equipments might not be occurred without the installation.
1. Fix the moistureproof sheet on the oor.
Plywood Floor : Wood Screw
Concrete Floor : Glue
2. Make a cut in the moistureproof packing according to piping position.
3. Peeled off the sheet on the adhesive face side of the moistureproof packing. Passes under the
piping and electric code on the moistureproof packing and attach to the oor.
4. Seal a space around the piping and electric code.
5-5. Installation of unit
1. Remove the four tapping screw(M8 x 60mm) xing the
unit base plate to the pallet.
Marking
Water Supply
Hot Water Pipe
Drain Pipe
Power Outlet
Pipe
5-3. Marking for unit xing position
Use supplied full scaletemplate to mark the
xing position on the oorr. Check the piping
and power outlet position before marking.
1. Put the supplied templete on the oor and hold with
the tape etc. It should be set to the position of
piping and power outlet.
2.The chair xing position is marked on the oor.
3. Make it holes for marked position. (8.5 mm x 50 mm )
4. Remove the template from the oor.
Base
Tapping Screw(M8 x 60)
Pallet
-6-

-7-
Templete
8.5 mm
50mm
or more deep
Floor
2~5mm
CAUTION
Base Plate
Hammer
Flat Washer Nut
Center pin
If the anchor bolt is tapped with its and contacting the bottom
of the hole, the strength will be lowered. Proper clear ance
must exist between the end of the anchor bolt and th e bottom
of the hole.
Do notmakescratchor damagetheoor while movingthe
unit. Please use the carriage jig to move it.
4. Fix the main unit with the four screws.
Plywood Floor : Hex head tapping screw M8 x 65
Concrete Floor : Anchor bolts M8 x 70
5. When the moistureproof packing is bigger than
main unit base, please cut it out.
Construction process of anchor bolts.
1.Drill the anchor holes
of a specic diameter
and depth.
2.Clean each anchor hole
thoroughly using a
vacuum cleaner, with a
narrow nozzleattachment
to reach into the hole and
remove all debris.
3.Insert the anchor bolt, tapping
it lightly with a hammer to seat
it. Position the material, and
then drive the center pin into
the anchor unit it is snug.
4.Adjust the fastening strength
of the nut using a wrench etc.
Hold the JigA and B to lift the unit by
2 workers to move it. Otherwise, breakage
may result in.
CAUTION
Carriage Jig A
Carriage Jig B
2. Hold the carriage jig and move the main unit to
marked position on the oor.
3. Decide the installation position and remove the
carriage jig A and B from main unit base.

-8-
Check Valve
Flexible Pip e
Packing
Stop Valve
Water Supply
Hot Water Supply
Drain Hose
Vinyl
Drain Pipe
Elbow
Packing
The height of drain pipe should be less than 60mm.
C A U T I O N
1. Insert the elbow to the drain pipe from floor with seals.
2. Adjust the length of drain pipe(VU40), so that the
one end of drain pipe(VU40) may become on the
edge of the base, and connect to elbow with seals.
3. Connect the drain hose packing to the drain pipe(VU40).
4. Through the drain hose clamp to the drain hose, and
connect the drain hose to the drain hose packing.
・The drain hose shall be free of dent.
・Attach the drain hose so as not to be folded.
5. Fasten the screw of the drain hose clamp for
drain hose.
・Tightening too hard may damage the drain hose.
Do not tighten too hard.
6. Cover theelbow partwiththevinyl.
5-6. Drain Pipe Connection
5-7. Water and Hot Water Supply Line Connection
1. Install the stop valve to each supply pipe.
2. Bend each flexible pipe to a suitable angle for
connection.
Check the each connection for leaks.
3. Connect the each Check Valve to the each stop
valve with the flexible pipe.
Make sure all connection is surely fixed.
please confirmed the water does not leak.
Drain Pipe(VU40)
C A U T I O N
C A U T I O N
Elbow and drain pipe(VU40) are not included
with shipment. Please prepare it beforehand.
Do not tear up the vinyl which is covered the drain hose.
C A U T I O N
Drain Hose Packing
Drain pipe(VU40)
Stepped Section
Drain pipe(VU40)
Elbow
Less than 60mm
Drain Pipe
from Floor Edge of Base Plate
Base Plate
Insert the drain hose packing
to the drain pipe(VU40) until
the stepped section hit to the
end of drain pipe(VU40).
Drain Hose
Base Plate
Edge of Base Plate
Vinyl
Drain pipe(VU40)
Drain Hose
Packing
Drain Hose Clamp
Drain Hose
Insert it in
this line
Match the center of the drain hose clamp
to this line of the drain hose.
Fastening
F.L.
F.L.