Takara Belmont Yume DX User guide

YUME DX
QUICK OPERATION GUIDE
BB-QG-YMDX-ENGeu 2106

2222

3
For details and safety information
see the operating instructions.
https://beauty.takarabelmont.co.jp/manual-site/

4
1 Foot Control/ Power Switch
EX-YM2XL : left side foot control
1 1 2 2
3 34 4
5 5
1 P1 Switch
2 P2 Switch
Seat lifting
Backrest raising
Seat lowering
Preset position 1 (Used mainly for shampooing position)
Preset Position 2 (Used mainly with the backrest upright)
Backrest reclining
Manual Mode Control
5
How to set the preset position
1) P1: Set the chair to the desired position
P2: Set the chair backrest to the desired position
2) Turn off the main switch
3) While depressing the Preset Switch (P1 or P2), turn on the main switch
4) Keep depressing the Preset Switch until the buzzer sounds, then release
3 Auto Return Switch
4 Lock Position Switch
Chair will move to the initial position automatically
Lock/unlock the chair rotating position
EX-YM2XR : right side foot control

5
2 Legrest Switch/Heater/Headrest
Legrest raising Legrest reclining
Legrest Switch
Headrest
Headrest
Headrest Handle
Remove the headrest when not in use

6
Cold
3 Shampoo Basin
Shampoo Basin
Tap Thermostatic Control
Stop
Button
Hot
On
Off
To adjust the temperature over 40 degrees,
turn the knob while pressing the Stop Button
Drain Cap (Old) Drain Cap (New)

7
4 Shower head
Water outlet
*Surface to clean
<YUME shower head>
Shower head holder
Rotate
Push
Push
Cover
-Consumable part
Sponge
Harder side of sponge to be
facing upwards.
Sponge holder
-Consumable part (wash daily)
Shower Head Holder

8
5 Preparation
1 Attach the Neck Cushion and Head Pillow.
Neck Cushion
Head Pillow
Attach
Attach
Head Pillow
Attach both sides of the Neck Cushion with
snap button.
Attach the head pillow as shown below.
2
3
Long side
(faces the chair)
Short side

HEATERHEATER
9
1 Turn on the power.
6 Operation procedures
ONOFF
2Press the auto return switch to bring the chair
to its initial position.
Auto Return Switch
3Instruct the customer to sit from the side,
then face front.
Initial Position
4Press the P1 switch (or manual mode control)
to bring the chair to its approximate position.
P1
Preset Position
Manual Mode Control

10
Face is in horizontal position
CAUTION
Adjust the chair height.
5
Confirm that there are no objects/people between the
seat/shampoo basin and the floor when operating the
chair.
6 Operation procedures
<Shampooing Style>
Basin Top
The basin top height should
match the practitioner’s hip
<Standing position>
Rear Shampoo
Side Shampoo
<Sitting position>

11
6 Operation procedures
Neck Cushion
Head Pillow
6After the shampooing, return the chair to its
initial position.
Initial Position
7Wipe off the remaining water after use.
8 Clean the consumable parts.
Hair CatcherDrain Cap
Auto Return Switch

12
7 Rotating the chair
1Press the P2 switch to bring the backrest to its
upright position.
P2
Backrest Upright
2Press the lock position switch to unlock the
chair rotation.
Lock Position Switch
The chair lock will not release when the backrest is
within 30 degrees.
30 degrees
3Rotate the chair to the desired position by
gently holding onto the backrest
⇒A clicking sound can be heard at the
60 and 90 degrees point
90°
0°
60°

13
7 Rotating the chair
4Press the lock position switch to lock the
chair rotation.
Lock Position Switch
CAUTION Confirm that there are no objects/people in the way
when rotating the chair.
5When finished, unlock the chair to return it to its
initial position (0°),andlock.
90°
0°
60°

TAKARA BELMONT CORPORATION
2-1-1, Higashishinsaibashi,Chuo-ku,Osaka, 542-0083, Japan
TEL : [phone]
FAX : [phone]