Takara Belmont BRAMU User manual

1. Move the chair to the installation location.
Be sure to store this manual in a secure location together with the operation manual as it describes
items that must be understood by the customer.
Hold the parts shown in gray while working.Hold the parts shown in gray while working.
Foot
switches Base
Backrest
Installation Manual
1
2017.02
BOOK NO. 1E01TUAEBOOK NO. 1E01TUAE
Base
Body
Foot switches Skirt
Installation Procedures
CAUTION
Body
Skid
Skid
●Move the chair by holding the skid.
(Carrying the chair by the upper
part is dangerous because the base
could come off and drop.)
●When the chair is still on the skid,
move the chair to the edge of the skid
as shown in the figure on the right, tilt
the chair and skid, and pull out the
skid. Removing the skid without tilting
it can result in the skid interfering with
the mechanisms on the underside of
the base, causing an abnormal noise to
be emitted when the chair is rotated.
●Remove the chair from the skid. Raise
the chair off the floor by holding the
metal plate under the foot switch.
Move the chair by holding the base
and body, or the metal plate of the foot
switches. Do not hold the chair by the
skirt.
•Hold onto the base, foot switches
and backrest, or the body when
performing procedures such as
transporting, installing the rubber
wheels to, or positioning the chair.
When holding the chair, be careful
not to wrinkle or dirty the leather,
and that the base does not come off.
•Make sure not to apply excessive
force that could damage the chair
even when holding by the parts
shown in the figure on the right.
Bang!

3. Connect the power plug with the outlet.
Prepare a outlet with an attached ground terminal.
※110/120 V AC (12 A or more), 220/230/240 V AC (7 A or more)

<If assembling together with the Yume Swing bowl>
2. Attach the rubber ring to the base.
Rubber ring
Base
4. Check that the chair operates normally.
Turn the power on and check that the chair raises/lowers normally, the backrest raises/reclines
normally, the legrest raises/lowers normally, and the rotation lock/release, preset feature,
and auto-return features operate normally.
Installation Manual
The chair must absolutely be grounded
in order to prevent electric shock.
Lock rotation at the Yume Swing setting position where the Yume Swing position setting and the
bowl position are optimally aligned. At that position, manually align the positions of the chair and
bowl, and set the preset setting. After completing the setting, return the chair to its original position
by using the auto-return switch, and use the preset switch to check the set position.
Determine the installation location. Lift the base off the floor and attach the rubber ring to the
rim of the base.
●It is easier to attach the rubber ring by lifting up one side of the chair at a time. Hold the
armrest and shoulder part of the backrest to balance the force, and tilt the chair body to
attach the rubber ring one side at a time. Do not apply excessive force to the armrest or other
parts, or strike it from above when tilting the chair body.
Be sure to ground the chair to prevent accident due to
current leakage and to improve the noise-dampening
performance of the control circuit.
Takara Belmont has no responsibility for any current
leakage that results if the above-indicated procedures are
not performed.
2

5. Install the step.
3
Be careful when the adjuster is extended that it does not scratch the floor or pull
the power cord when rotating the chair.
Legrest
Guide
Positioning stoppers
There are two adjusters on underside.
Loosen Tighten
Adjuster nut
Adjuster
Retract
Extend
Step fixture
Step (underside)
WARNING
CAUTION
Adjusting Preset Positions
Installation Manual
Insert the step at an angle (approx. 45°) and hook the step fixture on the guide while aligning
with the positioning stoppers.
⇒The adjuster, which prevents the chair from overturning, is located on the underside of the
step.
Adjust the adjuster by loosening the adjuster nut by using a wrench (No. 17), adjust the
height of the adjuster, and then tighten the adjuster nut by using a wrench (No. 17), as
shown in the figure above.
•After installing the step, check that the step fixture is securely held by the
guide and the step is not loose. Be careful that there is no looseness as this
could result in the chair tipping over when the customer is getting in or out of
the chair.
•Be careful when lifting and carrying the step, and of where you place it
because the step is heavy. Dropping the step could result in serious injury or
damage the floor.
Although the settings positions of the preset switches are previously set when shipped from the
factory, you can change the settings to positions that match your customers.
Refer to "Adjusting preset positions" on p. 21 of the Bramu Operation Manual, and change the
settings to match your customers.