Taurus BodyCraft SEBR6245 User manual

TFTF-
~ 240 Min.
CM
273 kg
SEBR6245.01.03
BodyCraft Functional TrainerHFT
SKU: SEBR6245
Assembly Instructions
L 102 | W 142 | H 208

2HFT

3
Content
1 GENERAL INFORMATION 6
1.1 Technical Data 6
1.2 Personal Safety 7
1.3 Set-Up Place 8
2 ASSEMBLY 9
2.1 General Instructions 9
2.2 Scope of Delivery 10
2.3 Assembly 12
3 STORAGE AND TRANSPORT 22
3.1 General Instructions 22
4 TROUBLESHOOTING, CARE AND MAINTENANCE 23
4.1 General Instructions 23
4.2 Faults and Fault Diagnosis 23
4.3 Maintenance and Inspection Calendar 24
5 DISPOSAL 24
6 RECOMMENDED ACCESSORIES 25
7 ORDERING SPARE PARTS 26
7.1 Serial Number and Model Name 26
7.2 Parts List 27
7.3 Exploded Drawing 29
8 WARRANTY 30
9 CONTACT 32

4HFT
Intended Use
The equipment may only be used for its intended purpose.
The equipment is suitable for home use and semi-professional use (e.g. hospitals, clubs, hotels,
schools, etc.). The equipment is not suitable for commercial or professional use (e.g. tness
studio).
Dear customer,
thank you for choosing training equipment of the brand Bodycraft. Bodycraft equipment inspires
with its multifunctionality and excellent quality. In terms of innovation and technology, it is one of
the highest quality tness equipment for home use. Bodycraft multi gyms, for example, oer a very
wide range of exercise possibilities. This ranges from traditional strength training such as bench
presses and rehabilitation exercises to workout for complex sports like golf, tennis or badminton.
Disclaimer
BodyCraft® is a registered brand of the company Fitness Authority Industrial Co., LTD. All rights
reserved. Any use of this trademark without the explicit written permission of Fitness Authority
Industrial Co., LTD is prohibited.
Product and manual are subject to change. Technical data can be changed without advance notice.

5
ABOUT THIS MANUAL
Please carefully read the entire manual before installation and rst use. The manual will help you to
quickly set up the system and explains how to safely use it. Make sure that all persons exercising with
the equipment (especially children and persons with physical, sensory, mental or motor disabilities)
are informed about this manual and its contents in advance. In case of doubt, responsible persons
must supervise the use of the equipment.
This equipment has been manufactured according to the latest safety knowledge.
As far as possible, potential safety hazards which could cause injury have been
eliminated. Make sure to carefully follow the instructions and that all parts are
securely in place. If required, read through the instructions again to correct any
mistakes.
Please pay close attention to the safety and maintenance instructions given here. The contract
partner cannot be held liable for damage to health, accidents or damage to the equipment when it
is not used in accordance with these instructions.
The following safety instructions may appear in this manual:
࣑ATTENTION
This notice indicates potentially hazardous situations which, if not avoided, may result in
property damage.
⚠CAUTION
This notice indicates potentially hazardous situations which, if not avoided, may result in slight
or minor injuries!
⚠WARNING
This notice indicates potentially hazardous situations which, if not avoided, may result in death
or serious injuries!
⚠DANGER
This notice indicates potentially hazardous situations which, if not avoided, will result in death
or serious injuries!
LNOTICE
This notice indicates further useful information.
Retain these instructions in a safe place for future reference, maintenance or when ordering
replacement parts.

6HFT
1 GENERAL INFORMATION
1.1 Technical Data
Weight and Dimensions
Packaging dimensions (L x W x H) and article weight (gross, incl. packaging) approx.:
Box 1: 205 cm x 38 cm x 16 cm 47.8 kg / 105.4 lbs
Box 2: 124 cm x 60 cm x 21 cm 65 kg / 143.3 lbs
Box 3 (2x): 27 cm x 14 cm x 13 cm 22.42 kg / 49.42 lbs
Box 4 (4x): 28 cm x 19 cm x 15 cm 31.27 kg / 68.94 lbs
Set-up dimensions (L x W x H) approx.: 102 cm x 142 cm x 208 cm
Article weight (net, excl. packaging) approx.: 272.2 kg / 600 lbs
Maximum user weight (chin-up): 150 kg / 330 lbs
Weight Stack
Quantity: 2
Weight plates: 19 + 1 per weight stack
Weight of one weight plate: 4.5 kg / 9.9 lbs
Cable length: 722 cm
Cable material: Steel
Cover material: Plastic
Pulley diameter: 90 mm
Transmission ratio: 2:1

7
1.2 Personal Safety
⚠DANGER
+ Before you start using the equipment, you should consult your physician that this type of
exercise is suitable for you from a health perspective. Particularly aected are persons who:
have a hereditary disposition to high blood pressure or heart disease, are over the age of 45,
smoke, have high cholesterol values, are overweight and/or have not exercised regularly in
the past year. If you are under medical treatment that aects your heart rate, medical advice
is absolutely essential.
+ Note that excessive training can seriously endanger your health. Please also note that
heart rate monitoring systems can be inaccurate. If you notice any signs of weakness,
nausea, dizziness, pain, shortness of breath, or other abnormal symptoms, stop exercising
immediately and seek advice from your doctor if necessary.
⚠WARNING
+ This equipment may not be used by children under the age of 14.
+ Children should not be allowed unsupervised access to the equipment.
+ Persons with disabilities must have a medical license and must be under strict observation
when using the equipment.
+ The equipment is strictly for use by one person at a time.
+ If your equipment provides a safety key, the clip of the safety key must be attached to your
clothing before starting your training. In the event of a fall, the EMERGENCY STOP of the
equipment can be initiated.
+ Keep your hands, feet and other body parts, hair, clothing, jewellery and other objects well
clear of moving parts.
+ During use, wear suitable sports clothing rather than loose or baggy clothing.When wearing
sports shoes, make sure they have suitable soles, preferably made of rubber or other non-
slip materials. Shoes with heels, leather soles, studs or spikes are unsuitable. Never exercise
barefoot.
⚠CAUTION
+ If your equipment needs to be connected to the power supply with a mains cable, make
sure that the cable is not a potential tripping hazard.
+ Make sure that nobody is within the range of motion of the equipment during training so as
not to endanger you or other persons.
࣑ATTENTION
+ Do not insert any objects of any kind into the openings of the device.

8HFT
1.3 Set-Up Place
⚠WARNING
+ Do not place the equipment in main corridors or escape routes.
⚠CAUTION
+ Choose a location in which to place the equipment such that there is enough free space/
clearance to the front, the rear and to the sides of the equipment.
+ The training room should be well ventilated during training and not be exposed to any
draughts.
+ Choose the place in which to set up the equipment such that there is enough free space/
clearance to the front, the rear and to the sides of the equipment.
+ The set-up and mounting surface of the equipment should be at, loadable and solid.
࣑ATTENTION
+ The device may only be used in one building, in suciently tempered and dry rooms
(ambient temperatures between 10°C and 35°C). The equipment should not be used
outdoors or in rooms with high humidity (over 70%) like swimming pools.
+ A oor protective mat/equipment underlay can help to protect high-quality oor coverings
(parquet, laminate, cork, carpets) from dents and sweat and can help to level out slight
unevenness.

9
2 ASSEMBLY
2.1 General Instructions
⚠DANGER
+ Do not leave any tools, packaging materials such as foils or small parts lying around,
as otherwise there is a danger of suocation for children. Keep children away from the
equipment during assembly.
⚠WARNING
+ Pay attention to the instructions attached to the equipment in order to reduce the risk of
injuries.
⚠CAUTION
+ Ensure to have sucient room for movement in each direction during assembly.
+ The assembly of the equipment must be carried out by at least two adults. If in doubt, seek
the help of a third technically skilled person.
࣑ATTENTION
+ To prevent damage to the equipment and the oor, assemble the equipment on a mat or
packaging board.
LNOTICE
+ In order to make the assembly as simple as possible, some screws and nuts to be used can
already be pre-assembled.
+ Ideally, assemble the equipment at its later set-up place.

10 HFT
2.2 Scope of Delivery
The scope of delivery consist of the following parts. At the beginning, check whether all parts
and tools belonging to the device are included in the scope of delivery and whether damage has
occurred. In the event of complaints, the contractual partner must be contacted directly.
⚠CAUTION
If parts of the scope of delivery are missing or damaged, the assembly must not be carried out.

11

12 HFT
2.3 Assembly
Before assembly, take a close look at the individual assembly steps shown and carry out the assembly
in the order given.
LNOTICE
First loosely screw all parts together and check that they t properly. Tighten the screws using
the tool only when you are instructed to do so.
Step 1: Assembly of the Base Frame Legs and Rear Upright Frames
1. Carefully attach two end caps (38) to each of the base frame legs (1R & 1L).
2. Attach the rear upright frames (4) to the right & left base frame legs (1R & 1L) with the eight pre-
installed 3/8”chromed washers (62) and 3/8”chromed nylon nuts (68).
3. Attach the top cross support (8) to the rear upright frames (4) with four 3/8” X 2-1/2” hex bolts
(52), eight 3/8”chromed washers (62) and four 3/8”chromed nylon nuts (68).
4. Attach the bottom cross support (9) to the rear upright frames (4) with four 3/8” X 2-1/2” hex
bolts (52), eight 3/8”chromed washers (62) and four 3/8”chromed nylon nuts (68).

13

14 HFT
Step 2: Assembly of the Upright Frames and the Top Frames
1. Slide the pulley height adjusters (15R & 16L) onto the upright frames (2R & 3L).
2. Attach the upright frames (2R & 3L) to the base frame legs (1R & 1L) with the four pre-installed
3/8”chromed washers (62) and 3/8”chromed nylon nuts (68).
࣑ATTENTION
Make sure to thread the hex bolts (49) from the bottom into the heigth adjusters (15R & 16L) in
the following step.
3. Attach two rotating pulley holders (17) to the right & left pulley height adjusters (15R & 16L)
with two 1/2”X 4-1/4” hex bolts (49), four 1/2”washers (61) and two 1/2”nylon nuts (67).
4. Attach the top frames (6R & 7L) to the rear upright frames (4) with two 3/8”X 4” black hex bolts
(51), four 3/8”black washers (63) and two 3/8”black nylon nuts (68).
5. Attach the top frames (6R & 7L) to the upright frames (2R & 3L) along with the chin bar (7) and
two pulleys (36) with four 3/8” X 4-1/4” black hex bolts (50), eight 3/8” black washers (63) and
four 3/8”black nylon nuts (68).
6. Tighten all bolts starting from the bottom.

15

16 HFT
Step 3: Assembly of the Guide Rods
1. Insert two plastic guide rod holders (24) into the outer holes of each of the base frame legs (1L
& 2R).
2. Insert two guide rods (5) into the plastic guide rod holders (24).
࣑ATTENTION
The stack spacers (23) must only be installed if you have 28 weight plates/14 per side. If you have
38 weight plates/19 per side, do not install the stack spacers (23) in the following step.
3. Slide two stack spacers (23) and two rubber donuts (22) over the guide rods (5).
4. Attach the selector rod (20) to the top plate (19) with the top plate bolt (48), tighten.
5. Thread the pulley block (18) into the selector rod (20) minimum 1/3 of the way (Fig. A).
LNOTICE
Make sure to orient the selector holes of the weight plates toward the inside bottom.
6. With the guide rods slightly angled (Fig. B), carefully slide each of the weight plates (21) over the
guide rods (5) one by one.
7. Slide the top plate (19) over the guide rods (5), running the selector rod (20) down through the
center holes of the weight plates (21). Insert the selector pin (41) into one of the selector holes.
8. Place the top guide rod holders (14) onto the guide rods (5) and secure to the top of the left top
frame (6L) with the two pre-installed hex socket dome bolts (56) and two 5/16”washers (64).
9. Tighten the two pre-installed set screws (60) and hex dome bolts (56).
10. Repeat the steps 1 to 9 on the other side.

17

18 HFT
Step 4: Assembly of the Cables and Pulleys
LNOTICE
+ The following steps show the assembly on the right side of the equipment. The steps must
be repeated for the left side as well.
+ The cables and pulleys must be installed simultaneously.
1. Fasten the ball end of the cable (27) to the pulley holder (17) with two Pulleys P1 and P2 (36)
with a total of two 3/8”X 1-3/4”hex bolts (53) and two 3/8”black nylon nuts (69) [Fig A].
2. Route the cable (27) over the two pulleys P3 and P4 and mount pulley P4 to the right top frame
(6R) with one 3/8”X 4”black hex bolt (51), two 3/8”black washers (63) and one 3/8” black nylon
nut (69) [Fig B].
3. Route the cable (27) down through the pulley block (18) and around pulley P5. Mount the pulley
P5 to the pulley block (18) with one 3/8”X 1-3/4”hex bolt (53) and one 3/8”black nylon nut (69)
[Fig C].
4. Route the cable (27) up over the pulleys P6 and P7 (36) through the right top frame (6R). Mount
the pulleys P6 and P7 to the right top frame (6R) with a total of two 3/8”X 4”black hex bolts (51),
four 3/8”black washers (63) and two 3/8”black nylon nuts (69) [Fig B].
5. Route the cable (27) down through the pulley holder on the base frame leg and around pulley
P8 (36). Mount the pulley to the pulley holder using one 3/8”X 1-3/4”hex bolt (53) and one 3/8”
black nylon nut (69) [Fig. D].
6. Route the cable (27) up and screw the bolt end of the cable (27) at least 1/3 into the bolt holder
that is welded onto the right pulley height adjuster (15R) [Fig. E].
7. Repeat the steps for the left side.
LNOTICE
If necessary, the cables can be tightened or loosened by adjusting the screw conntections on
the height adjusters (15R & 16L) [Fig. E] or on the pulley blocks (18) [Fig. C].
8. Tighten all jam nuts rmly [Fig. C & E].

19

20 HFT
Step 5: Assembly of the Weight Panels
1. Loosely attach the weight panels (10R & 11L) to the rear upright frames (4) with eight plastic
studs (43), four 1/4”X 6”hex bolts (54), eight 1/4” washers (66) and four 1/4”nylon nuts (70).
2. Loosely attach the weight panels (10R & 11L) to the base frame legs (1R & 1L) with the two pre-
installed 5/16”X 1/2” button head bolts (55) and two 5/16”washers (65).
3. Tighten the weight panel bolts (54 & 55).