Teac TD-01 Portable User manual

Portable Indicator Owner’s Manual
Z
TD-01 Portable
D01285105A

2
Introduction
Thank you for purchasing the TD-01 Portable Indicator.
Please read this document in its entirety before using the
product to get the best performance and ensure safe and
proper operation.
Features
oFive-digit digital display enables direct reading of physical
quantities up to ±99999.
oSupport for TEDS sensors makes calibration easy.
Automatic calibration is also possible when a TEDS sensor
is connected.
oAn equivalent input function is included, making sensitivity
adjustment without actual loads easy.
oStatic strain measurement is possible. Identifying load cell
defects and other problems through plastic deformity is
easy.
oSupports high and low limit comparison functions
oSupports a variety of functions, including peak hold, bot-
tom hold and holds with zone designations.
oD/A output according to designated values is a standard
feature.
oProduct is RoHS compliant
oWaveform display function allows input signals to be
checked as waveforms.
oInterrupted wire checking function built-in
o300 indicator values and 8 graphs can be saved in the inter-
nal memory
Disclaimers
Information is given about products in this manual only
for the purpose of example and does not indicate any
guarantees against infringements of third-party intellectual
property rights and other rights related to them. TEAC
Corporation will bear no responsibility for infringements on
third-party intellectual property rights or their occurrence
because of the use of these products.
Included accessories
If anything is missing or damaged, contact us. (For contact
information, see the last page.)
CR2032 button cell battery (preinstalled in unit) 1
AA batteries 4
Micro USB cable 1
Operation manual (this document) 1
Company names and product names in this document are the
trademarks or registered trademarks of their respective owners.

3
Safety information
This document describes the safety instructions for the operation of the digital indicator. Before operating the product, read this doc-
ument carefully to familiarize yourself with the unit.
VWARNING Follow the instructions below to avoid risk of serious personal injury and
death.
Never use beyond the rated specifications as there is the danger of property damage, injury, fire or electrical shock.
Never use in flammable gaseous environments including the following locations as there is the danger of explosion.
Locations containing corrosive or flammable gases
Locations near water, oil or subject to chemical splash
If the product malfunctions (any smoke, odor or noise is present), stop operating the product immediately and unplug the power
cord as there is the danger of fire or electrical shock.
Never attempt to disassemble the product.
Carefully check connections and wiring before applying power.
Do not allow foreign objects such as metal fragments that result from cutting panels, wires or other materials to enter this unit.
If the unit is dropped or subject to strong impacts, it could break. If this occurs, stop using it and contact the seller from which you
purchased it.
If the unit is used in a manner not specified by the manufacturer, the protection provided by the unit may be impaired.
VPrecautions concerning batteries
Misuse of batteries could cause them to rupture or leak leading to fire, injury or the staining of nearby things. Please read and observe
the following precautions carefully.
oBe sure to insert the batteries with correct positive (¥) and negative (^) orientations.
oUse batteries of the same type. Never use different types of batteries together.
oIf the remote control is not used for a long time (more than a month), remove the batteries to prevent them from leaking.
oIf the batteries leak, wipe away the leakage inside the battery compartment and replace the batteries with new ones.
oDo not use batteries of types other than those specified. Do not mix new batteries with old ones or use different types of batteries
together.
oDo not heat or disassemble batteries. Never throw batteries into fire or water.
oDo not carry or store batteries with other metallic objects. The batteries could short circuit, leak or explode.
oNever recharge a battery unless it is confirmed to be a rechargeable type.
VWARNING
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD
oThis product contains a coin/ button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in
just 2 hours and can lead to death.
oKeep new and used batteries away from children.
oIf the battery compartment does not close securely, stop using the product and keep it away from children.
oIf you think batteries might have swallowed or placed inside any part of the body, seek immediate medical attention.

4
VCAUTION Follow the instructions below to avoid risk of personal injury or property damage.
Put the unit power into standby before doing any of the following.
oInstalling load cells
oReplacing batteries
oConnecting other external equipment
Never touch the connectors while the product is turned on.
When connecting to a power supply or signal input/output connector, be sure to wire them correctly after confirming the signal
names and pin assignment numbers. Use shielded cables for signal input/output cables (load cell, external input/output).
Conduct wiring in a place so that it will not be together or parallel with electrical wiring.
Avoid use in locations like the following.
oNear a power line
oWhere a strong electric or magnetic field is present
oWhere static electricity or noise, (for example, from a relay) is generated
Do not install in the following environments.
oLocations subject to temperatures exceeding the specified temperature and humidity ranges
oLocations subject to radiant heat from heat sources
oLocations with high salt or iron content
oLocations exposed to dirt and dust
oLocations subject to direct vibration or shock
oLocations subject to severe temperature changes
oOutdoor, or locations with an altitude of higher than 2000 m
oLocations where freezing or condensation might occur
Do not operate a damaged unit.
If the front panel is dirty, wipe it with a soft cloth lightly dampened with a solution of a neutral detergent and water. Then wipe
it again with a slightly damp cloth. DO NOT use a chemically treated dust cloth, paint thinner, or other flammable solvents. Using
any of them could damage the coating of the product.
If the product is used in a manner unintended by the manufacturer, the user's safety may be adversely affected.
Always attach the back cover when an electric current is present.
If subject to electromagnetic waves (from transceivers, mobile phones, amateur wireless transmissions, etc.), use metal pipes for
the wiring or make other countermeasures using shielding.
Safety information

5
Model for USA
This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: 1) This device may
not cause harmful interference, and 2) This device must
accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide rea-
sonable protection against harmful interference when the
equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residen-
tial area is likely to cause harmful interference in which case
the user will be required to correct the interference at his
own expense.
CAUTION
Changes or modifications to this equipment not expressly
approved by TEAC CORPORATION for compliance could
void the user’s authority to operate this equipment.
Model for Canada
Industry Canada’s Compliance Statement:
This Class A digital apparatus complies with Canadian
ICES-003.
CET APPAREIL NUMÉRIQUE DE LA CLASSE A EST CONFORME
À LA NORME NMB-003 DU CANADA
CAN ICES-3 (A) / NMB-3 (A)
Safety information
Model for Europe
This product complies with the European
Directives request, and the other
Commission Regulations.
For European Customers
Disposal of electrical and electronic equip-
ment and batteries and/or accumulators
a) All electrical/electronic equipment and waste batter-
ies/accumulators should be disposed of separately
from the municipal waste stream via collection
facilities designated by the government or local
authorities.
b) By disposing of electrical/electronic equipment
and waste batteries/accumulators correctly, you
will help save valuable resources and prevent any
potential negative effects on human health and the
environment.
c) Improper disposal of waste electrical/electronic
equipment and batteries/accumulators can have seri-
ous effects on the environment and human health
because of the presence of hazardous substances in
the equipment.
d) The Waste Electrical and Electronic
Equipment (WEEE) symbols, which show
wheeled bins that have been crossed out,
indicate that electrical/electronic equip-
ment and batteries/accumulators must be
collected and disposed of separately from
household waste.
If a battery or accumulator contains more
than the specified values of lead (Pb),
mercury (Hg), and/or cadmium (Cd) as
defined in the Battery Directive (2006/66/
EC), then the chemical symbols for those
elements will be indicated beneath the
WEEE symbol.
e) Return and collection systems are available to end
users. For more detailed information about the dis-
posal of old electrical/electronic equipment and
waste batteries/accumulators, please contact your city
office, waste disposal service or the shop where you
purchased the equipment.
Pb, Hg, Cd

6
Contents
Introduction..................................................2
Features ...................................................2
Included accessories .......................................2
Safety information ............................................3
Model for Europe.......................................5
Model for USA..........................................5
Model for Canada ......................................5
For European Customers ...............................5
Disposal of electrical and electronic equipment and
batteries and/or accumulators........................5
Installing batteries ............................................8
AA batteries................................................8
Replacing batteries .....................................8
Button cell battery .........................................8
Removing the button cell battery.......................8
Installing a button cell battery ..........................8
1.Names and functions of parts...............................9
1-1.Front panel ............................................9
1-2.Top panel ............................................ 10
1-3.Sensor signal input terminals......................... 11
1-4.Bottom panel ........................................ 11
1-5.Screen transition diagram ............................ 12
1-6.Home Screen ........................................ 13
1-6-1.Indicator value screen .......................... 13
1-6-2. Graph screen ................................... 14
1-6-2-1.Snapshot................................... 15
1-7.Static Strain Disp. Mode .............................. 15
1-8.Simple indication .................................... 15
2.Shortcut menus .......................................... 16
2-1.Memory and list selection/display.................... 16
2-1-1.Sensor value memory .......................... 16
2-1-2. Setting Memory ................................ 16
2-1-3.Indicator value list .............................. 17
2-1-4.Graph list....................................... 18
2-2.Indicator recording mode ............................ 19
2-2-1.Indicator recording mode ...................... 19
2-2-2.Overwrite oldest first ........................... 19
2-2-3.Showing the list of recorded indicator values ... 19
2-3.Recording graph data ................................ 19
3.Making connections...................................... 20
3-1.Connecting with the terminal bank .................. 20
3-2.Connecting a strain gauge transducer................ 20
3-2-1.Notes about bridge voltage (applied voltage)... 20
3-3.Interrupted wire checking............................ 21
4.Settings .................................................. 22
4-1.Basic operation ...................................... 22
4-2.Selecting setting values from options ................ 23
4-3.Inputting numerical setting values ................... 23
4-4.Changing the decimal point position................. 24
4-5.Lock ................................................. 24
4-6.Returning to the Home Screen ....................... 25
4-7.Viewing the version .................................. 25
4-8.Initializing all settings ................................ 25
4-9.Setting menu list..................................... 25
4-9-1.Calibration ..................................... 25
4-9-2.Condition Setting .............................. 26
4-9-3.Comparison Setting ............................ 26
4-9-4.Hold Function Setting .......................... 26
4-9-5.Graph settings.................................. 26
4-9-6.System settings 1............................... 26
4-9-7.System settings 2............................... 26
4-9-8.TEDS Settings .................................. 26
4-10.Setting value list .................................... 27
4-10-1.Calibration .................................... 27
4-10-2.Condition Setting ............................. 28
4-10-3. Comparison Setting ........................... 28
4-10-4.Graph settings ................................ 28
4-10-5.System settings 1 ............................. 29
4-10-6.System settings 2 ............................. 29
4-10-7.TEDS Settings ................................. 29
5.Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
5-1.Procedures shared by all calibration methods ........ 31
5-1-1.Locking and unlocking calibration values ....... 31
5-2.Equivalent input calibration .......................... 32
5-2-1.Sensor value memory selection................. 32
5-2-2.Excitation Voltage .............................. 32
5-2-3.Rated Output................................... 33
5-2-4.Rated Capacity ................................. 33
5-2-5.Zero Balancing ................................. 33
5-2-6.Select EU ....................................... 33
5-2-7.Cal. Value Lock.................................. 33
5-3.Actual Load Calibration .............................. 33
5-3-1.Sensor value memory selection................. 33
5-3-2.Excitation Voltage .............................. 33
5-3-3.Zero Balancing ................................. 34
5-3-4.Rated capacity (load calibration) ................ 34
5-3-5.Select EU ....................................... 34
5-3-6.Max. Disp. Value ................................ 34
5-3-7.Cal. Value Lock.................................. 34
5-4.TEDS calibration...................................... 35
5-4-1.Sensor value memory selection................. 35
5-4-2.Rated Output/Rated Capacity display ........... 35
5-4-3.Zero Balancing ................................. 35
5-4-4.Select EU ....................................... 36
5-4-5.Cal. Value Lock.................................. 36
5-5.Sensor value memory................................ 36
5-6.Select Min. Grid ...................................... 36
5-7.Max. Disp. Value...................................... 36
5-8.Select EU ............................................ 37
5-9.Sensor input logic.................................... 37
5-10.Zero Balancing...................................... 37
5-11.Digital Zero ......................................... 37
6.Condition Settings........................................ 38
6-1.Filter ................................................. 38
6-1-1.Select Num. of Moving Avg. .................... 38
6-2.Motion Detect ....................................... 39
6-2-1.Time ........................................... 39
6-2-2.Width .......................................... 39
6-3.Zero Tracking ........................................ 40
6-3-1.Time ........................................... 40
6-3-2.Width .......................................... 40
6-4.Digital Zero Offset.................................... 41
6-5.Digital Zero .......................................... 41
6-5-1.Enable Digital Zero ............................. 41
6-5-2.Digital Zero Limit Value ......................... 41

7
Contents
6-5-3.Clear Digital Zero............................... 41
6-6.Select Data Output................................... 42
7.Comparison Setting ...................................... 43
7-1.Comp. Value Setting ................................. 43
7-2.Comp. Mode Setting ................................. 43
7-3.Hysteresis............................................ 44
7-4.Nearly Zero .......................................... 45
8.Hold Function Setting .................................... 46
8-1.Hold Mode........................................... 46
8-1-1.Sample and hold ............................... 47
8-1-2.Peak hold ...................................... 48
8-1-2-1.No zone definition ......................... 48
8-1-2-2.Zone definition used ....................... 49
8-1-3.Bottom hold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
8-1-3-1.No zone definition ......................... 50
8-1-3-2.Zone definition used ....................... 51
8-2.Zone Definition ...................................... 52
8-3.Auto Zero............................................ 52
9.Graph settings............................................ 53
9-1.Time axis setting (X).................................. 53
9-2.Indicator value axis setting (Y)........................ 53
9-3.Trigger mode ........................................ 53
9-4.Trigger ............................................... 53
9-4-1.Trigger polarity ................................. 53
9-4-2.Trigger level .................................... 54
9-4-3.Trigger position ................................ 54
10.System settings 1........................................ 55
10-1.Setting Memory .................................... 55
10-2.D/A Converter ...................................... 55
10-2-1.D/A output ................................... 55
10-2-2. D/A Zero ...................................... 56
10-2-3.D/A Full Scale ................................. 56
10-2-4.D/A Max. Voltage.............................. 57
10-2-5.D/A CAL TEST ................................. 57
10-3.Lock ................................................ 57
10-3-1.Cal. Value Lock ................................ 57
10-3-2.Setting value lock ............................. 57
10-4.Brightness .......................................... 58
10-4-1.Brightness .................................... 58
10-4-2.Backlight dimmer ............................. 58
10-5.Auto power off ..................................... 58
10-6.Languages.......................................... 58
10-7.Reset to the Factory Settings ........................ 59
10-8.Device number ..................................... 59
10-9.Date & time setting ................................. 59
10-9-1.Date display format ........................... 59
10-9-2.Date & time setting. . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
11.System settings 2........................................ 60
11-1.Battery type ........................................ 60
11-2.Indicator recording mode........................... 60
11-3.Recorded data deletion ............................. 60
12.TEDS Settings ........................................... 61
12-1.TEDS Data .......................................... 61
13.Error message list........................................ 62
14.Specifications ........................................... 63
15. Block diagram ........................................... 65

8
Installing batteries
Remove the back cover and insert the batteries.
Close the cover after inserting the batteries
V Misuse of batteries could cause them
to rupture or leak, which might result in fire,
injury or the staining of nearby materials. Please
read and observe the precautions on page 3
carefully.
AA batteries
Insert four AA batteries with their +/− oriented as shown in
the case.
Replacing batteries
When replacing the AA batteries, replace all 4 of them with
new ones.
Dispose of the used batteries according to the instructions on
them or requirements set by your local municipality.
oContinuous operation time on battery power is approxi-
mately 24 hours (when the sensor load is 350 Ω and EVOLTA
alkaline batteries are used).
Button cell battery
The button cell battery is used to back up the clock.
Replace the button cell battery if the clock display shows that
it is January 1, 2000 after the power is turned on, except for the
first time you start the unit after purchase.
oWhen the unit is shipped new, a button cell battery is
already installed to allow you to check operation of the unit.
This battery is provided for checking operation and might
not last very long.
Removing the button cell battery
Insert a fine-tipped rod into the right side of the button cell
battery holder to unlock the battery.
Installing a button cell battery
Insert the button cell battery into the left side of the button
cell battery holder, and press the right side of the battery.

9
1. Names and functions of parts
A REC/REC MENU button
REC
When the indicator recording mode is set to “When
REC key pressed”, the indicator value is recorded
each time this button is pressed (page 19).
REC MENU
Press and hold this to open the indicator recording
mode screen (page 19).
B ESC/ZERO button
When holding, this button clears the hold value.
Press when a setting screen is open to move up one level.
When Cal. Value Lock is OFF, press and hold to use the
Zero Balancing function (page 37).
When Cal. Value Lock is ON, press this to forcibly set the
indicator value to zero (Digital zero function).
oPress and hold the ESC and ENT buttons simultane-
ously to check for interrupted wires.
C Display
This shows indicator and setting values.
If the sensor input is abnormal or the indicator value can-
not be shown, one of the following overflow messages
will be shown.
−LOAD: A/D converter minus over
1-1. Front panel
A
BF
E
D
C
Continued on the next page e

10
LOAD: A/D converter plus over
−FULL: display minus over
(less than the minimum display value)
FULL: display plus over (greater than the maximum dis-
play value)
−OVER FULL: Input is outside the input range (neg-
ative value)
OVER FULL: Input is outside the input range (posi-
tive value)
D READ/button
Press to open the memory and list selection/display
screen (page 16).
Press and hold to put the unit in standby or turn it off.
E Setting buttons
MENU
Press when an indicator value or graph is shown to
open the Function Menu (page 22).
5b
Select setting items and change setting values.
Use when changing a setting value to change the
value, symbol or decimal point position.
gt
Change the screen shown (page 12).
Press when a setting screen is open to select setting
items and setting value digits.
STRAIN
Press and hold the 5button to open static strain
display.
LOCK
Press and hold the bbutton to enable/disable the
control lock function.
CAL
Press and hold the gbutton to open the sensor
value memory screen.
TEDS
When a TEDS sensor is connected, press and hold
the tbutton to open the TEDS calibration screen.
F ENT/HOLD button
Press and hold to start operation of the hold function.
Press and hold this button again to disable the hold
function.
Press when changing a setting value to confirm the set-
ting item or setting value and move to the next item.
1-2. Top panel
AB C
oConnector covers are attached to the connectors. Remove
the connector covers to use the connectors.
oFor explanation purposes, the illustration above does not
show the connector covers.
A D/A OUTPUT connector
The D/A output is isolated from this unit's circuits.
B Sensor signal input terminal (INPUT 2)
These connectors are for connecting strain gauge trans-
ducers and TEDS sensors.
Compatible plug:
PRC03-12A10-7M10.5 (made by Tajimi Electronics
Co., Ltd.)
C Sensor signal input terminal (INPUT 1)
Terminal bank for connecting strain gauge transducers
and TEDS sensors.
1. Names and functions of parts