Techni Mobili RTA - 2336 User manual

MODEL RTA-2336
MODEL RTA - 2336
Thanks for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Please save this manual for future reference.
ASSEMBLY INSTRUCTIONS

RTA-2336

23
14
78
56
910 11 12
RTA-2336
PARTS LIST
Right
Left
P.3
X2 SETS
X2 X2
2
7
9
10
4
19
24
25
21
20
Left Panel Right Panel Bottom Panel Bottom Front Panel
Back Panel Middle Front Panel Top Panel Slider
Top Drawer Front
Panel
Bottom Drawer Front
Panel
Drawer Left Panel Drawer Right Panel

RTA-2336 P.4
1817
23
19
20 21 22
1413 16
15
2624 25
27
X4X2X2 X6
X2
X2
X2
Drawer Bottom Panel Drawer Back Panel Drawer Connect Studs
Rotating Structure Support Tube Big Table Top
Back Structure Front Structure Short Connect Tube Long Connect Tube
Small Table Top Big Side Panel Support Structure
Caster

RTA-2336 P.5
SCREWS LIST
A
B
C
3X15 MM
6X40 MM
4X14 MM
24
24
16
PART QTY. ITEM PART QTY. ITEM
D
E4X35 MM
8
1
F4
G
H
6X15 MM
4
I
6
6
J6
1
20
6X25 MM
6X20 MM
6X40 MM
6X50 MM
M6
1
KΦ16MM4

30mm
P.6
RTA-2336

RTA-2336 P.7
ASSEMBLY STEPS:
15
11
12
SCREWS
D
2PCS
6X15 MM
SCREWS
A
4PCS
3X15 MM
SCREWS
4PCS
4X35 MM
E
12
8
8
Left
Right
SCREWS
A
4PCS
3X15 MM
12
3
4
Use screws A to assemble the Drawer Connects (15)
to the Drawer Left and Right Panels (11 & 12).
9
11
12
10
&
Use screws D to assemble the Drawer Connects (15)
to the Top Drawer Front Panel and Bottom Drawer
Front Panel (9 & 10).
Slide in the Drawer Bottom Panel (13).
Use screws E to assemble the Drawer
Back Panels (14) to the Drawer Left and
Right Panels (11 & 12).
Grab the 2 sets of the Drawer Sliders (8) and separate the flat
ones from the “L” shaped ones. Place the drawer upside-
down as shown and use screws A to assemble the “L” shaped
Sliders to the Drawer Left & Right Panels (11 & 12) as shown.
IMPORTANT: REFER TO THE DRAWINGS FOR THE CORRECT
POSITION OF THE SLIDERS. If they get installed incorrectly,
the drawers will raise 1" with a gap at the bottom and the top
drawer will not close!
REPEAT STEP 3 TO 4 FOR THE OTHER DRAWER
11
12
13
11
12
14

RTA-2336 P.8
2
1
8
Right
Left
8
X2 X2
SCREWS
A
8PCS
3X15 MM
1
2
16
16
20
21
16
16
5
6
Insert the Studs (16) to the Left Panel, Right Panel,
Back Structure and Front Structure (1,2,20 & 21).
Grab 2 sets of the Flat Sliders (8) and use screws A to assemble
them to the Left & Right Panels (1 & 2) as shown.
The wheel on the sliders go facing to the FRONT and the screw
goes on the hole after the wheel as shown.
Please pay attention to the direction of the panles.

RTA-2336 P.9
3
4
5
SCREWS
4PCS
6X40 MM
B
7
First screw bolts B to the Bottom Front Panel and Back Panel (4 & 5),
then assemble the Bottom Panel (3) as shown and as explained in page 5.
1
2
5
3
4
6
SCREWS
14PCS
6X40 MM
B
8
First screw bolts B to the Left Panel (1) and Right Panel (2), then
assemble the Bottom Panel, Bottom Front Panel, Back Panel and
Middle Front Panel (3,4,5 & 6) as shown and as explained in page 5.
1
2
7
SCREWS
4PCS
6X40 MM
B
9
First screw bolts B to the Top Panel (7), then assemble it to the Left
and Right Panel (1 & 2) as shown and as explained in page 5.

RTA-2336 P.10
23
20
21
SCREWS
4PCS
6X40 MM
G
10
Use screws G to assemble the Long Connect
Tube (23) to the Back Structure and Front
Structure (20 & 21).
20
21
22
SCREWS
4PCS
6X20 MM
F
11
Use screws F to assemble the Short Connect
Tube (22) to the Back Structure and Front
Structure (20 & 21).
19
18
SCREWS
8PCS
4X14 MM
C
12
Use screws C to assemble the Support
Tube (18) to the Big Table Top (19).

RTA-2336 P.11
19
20
21
23
SCREWS
6PCS
6X50 MM
H
13
Use screws H to assemble the Back Structure, Front
Structure and Long Connect Tube (20,21 & 23) to the
Big Table Top (19).
24
25
SCREWS
2PCS
6X40 MM
B
24
25
26
SCREWS
D
8PCS
6X15 MM
X2
14
15
First screw bolts B to the Small Table Top (24), then
assemble it to the Big Side Panel (25) as shown and
as explained in page 5.
Use screws D to assemble the Support Structures (26)
to the Small Table Top and Big Side Panel (24 & 25).

RTA-2336 P.12
25
24
27
SCREWS
8PCS
4X14 MM
C
2PCS
6X25 MM
I
J
2PCS
M6
16
18
Use screws C to assemble the Support Tube (18) to the Small Table Top (24).
Use screws I & J to assemble the Casters (27) to the Big Side Panel (25).
17A
17B
17E
17C
17D
17D
17D 17C
17E
17D 17F
17
24
17E
SCREWS
D
4PCS
6X15 MM
17 18
Use Allen Wrench to disassemble the Rotating
Structure (17) as shown.
NOTE: It is recommended to keep all the parts
for (17) laid out in the same order shown above
for easy re-assembly later.
Use screws D to assemble one of the part 17E to the
Small Table Top (24).

RTA-2336 P.13
17A
17B
17C
17D
17D
17D 17C
17E
17D 17F
19
Use Allen Wrench to assemble the Rotating
Structure (17) as shown.
7
SCREWS
4PCS
6X25 MM
I
J
4PCS
4PCS
KΦ16 MM
M6
17A
20
Use screws I, J & K to assemble the Rotating Structure (17)
to the Top Panel (7) as shown.

RTA-2336 P.14
19
17E
SCREWS
D
4PCS
6X15 MM
21
22
Use screws D to assemble the Rotating Structure (17)
to the Big Table Top (19).
Tighten any and all screws.
Insert the drawers into the cabinet, starting with the bottom drawer.
You might have to insert it at a downward tilted angle.
9
10

English
- DO NOT EXPOSE THE SURFACES TO DIRECT SUNLIGHT OR EXTREME
ENVIRONMENTAL CONDITIONS. ANY DAMAGE RESULTING FROM SUCH
EXPOSURE IS NOT COVERED BY THE PRODUCT’S WARRANTY.
- THE PREFERABLE METHOD TO CLEAN THE SURFACES IS TO WIPE THEM
USING A SOFT CLOTH DAMPENED WITH A SOLUTION SOAP AND WATER,
THEN DRY WITH A CLEAN TOWEL.
- DO NOT SPRAY SOLVENTS OR CLEANING AGENTS DIRECTLY OVER THE
SURFACES, STRUCTURAL TUBES OR METAL PARTS.
- DO NOT LEAN, SEAT OR STAND OVER THE UNIT.
- DO NOT ALLOW CHILDREN TO PLAY OVER/UNDER THE UNIT, NOR ALLOW
THEM TO REACH INSIDE ANY COMPARTMENTS WITHOUT THE SUPERVISION
OF AN ADULT.
- BEFORE MOVING OR TRANSPORTING THE UNIT, MAKE SURE THAT:
ALL HEAVY OBJECTS OR THAT MIGHT FELL OFF ARE REMOVED FROM
THE UNIT.
IF THE UNIT ARE ON CASTERS (WHEELS), MAKE SURE THAT ALL ARE
UNLOCKED.
THE UNIT MUST BE HANDLED BY AT LEAST 2 PERSONS.
WHEN LIFTING THE UNIT, USE BOTH OF YOUR HANDS, AND BEND YOUR
KNEES. REMEMBER TO ALWAYS LIFT WITH YOUR LEGS, NOT YOUR BACK.
- IN CASE OF DAMAGE TO ANY PARTS, NOTIFY THE VENDOR AS SOON AS
POSSIBLE.
- IN CASE OF GLASS BREAKAGE (IF THE UNIT HAS A GLASS TABLE TOP OR
PARTS MADE OF GLASS) DO NOT HANDLE THE BROKEN GLASS WITH YOUR
BEAR HANDS, AND CONTACT THE VENDOR IMMEDIATELY. DO NOT ALLOW
CHILDREN NEAR THE BROKEN GLASS.
CARE AND MAINTENANCE