Home Styles 5648 49 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestylesfurniture.com,
[email protected], 888-680-7460, 877-831-0319
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
5648 49-
Hall Tree Storage Bench
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
A.
Seat
1 pc.
E.
Back Panel
1 pc.
D.
Front Panel
1 pc.
F.
Base
1 pc.
B.
Side Panel
1 pc.
C.
Side Panel
1 pc.
H.
Side Panel
1 pc.
I.
Side Panel
1 pc.
G.
Top
1 pc.
J.
Back Frame
1 pc.
K.
Back Frame
1 pc.
N.
Arm
1 pc.
M3.5x16
Wood Screw
for Spring Support
8 pcs. (+1 extra)
M6x50
Head Cap Bolt (long)
8 pcs. (+1 extra)
Cross Dowel
8 pcs. (+1 extra)
M6x35
Head Cap Bolt
24 pcs. (+1 extra)
M6x30
Head Cap Bolt (short)
4 pcs. (+1 extra)
Small Hex Wrench
1 pc.
Hex Wrench
1 pc.
M4x16
Wood Screw for Hook
8 pcs. (+1 extra)
Hook
4 pcs.
Wood Plug
20 pcs. (+1 extra)
M.
Arm
1 pc.
L.
Back Stretcher
2 pcs.
Spring Support
2 pcs.

Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened up in the future.
STEP 1
Attach Side Panels (B) and (C) to Front Panel (D) and Back Panel (E)
with Cross Dowels and Head Cap Bolts (long). (See Figure 1)
B
C
D
E
Head Cap Bolt (long)
Cross Dowel
Figure 1
Spring Support
Wood Screw for Spring Support
A
STEP 2
Attach Spring Supports to Seat (A)
by inserting Wood Screws for
Spring Support into pre-drilled holes,
then tighten. (See Figure 2)
Figure 2

Assembly Instructions 3/6
F
A
Head Cap Bolt
Wood Plug
Figure 3
STEP 3
Insert Base (F) into unit.
Attach Seat (A) to unit
with Head Cap Bolts.
Cover all holes with Wood Plugs.
(See Figure 3)
Figure 4
STEP 4
Attach Hooks to Back Frame (J) by
inserting Wood Screws for Hook
into pre-drilled holes, then tighten.
(See Figure 4)
Hook
Wood Screw for Hook
J

Assembly Instructions 4/6
L
L
J
K
STEP 5
Assemble Back Frames (J), (K) and (L) together.
H
I
STEP 6
Attach Side Panels (H) and (I) to unit with Head Cap Bolts.
Head Cap Bolt

STEP 8
Attach top unit to base unit
with Head Cap Bolts (short).
Cover all holes with Wood Plugs.
Level unit by adjusting the adjustable
levelers on bottom of unit.
(See Figure 5)
Note: Unit must be level to work properly.
Head Cap Bolt (short)
Figure 5
Assembly Instructions 5/6
Wood Plug
G
M
N
Head Cap Bolt
STEP 7
Attach Top (G) and Arms (M), (N)
to unit with Head Cap Bolts.

Hardware List
Assembly Instructions 6/6
Drill 3/8” hole in wall
Top of unit
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
IMPORTANT
To help reduce the risk of the unit tipping over, the Tipover Restraint must be installed following these instructions exactly.
STEP 9
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tipover Restraint through
Bracket on wall and Bracket on unit.
(See Figure 6)
Put tie end of Tipover Restraint into lock
end of Tipover Restraint and pull until tight.
Bracket
on wall
Anchor in wall
3/8” wall hole
Tie end
Lock end
Bracket at
top of unit
Tipover
Restraint
Figure 6
Wood Screw
Wall Screw Pre-drilled hole
at top of unit

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestylesfurniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestylesfurniture.com,
[email protected], 888-680-7460, 877-831-0319