Techni Mobili RTA-8030 User manual

ASSEMBLY INSTRUCTIONS FOR CHAIR MODEL
RTA-8030
PARTS LIST
ATTENTION: Before you begin the assembly,
make sure that all parts are included in good
condition.
ATTENTION:
⚠Follow the in truction tep by tep.
⚠To avoid mi alignment , leave the crew loo e and do not tighten them until all are in their re pective place .
⚠Do not overtighten or force the crew a they could break, trip, or damage the thread of the hole .
⚠U ing the wrong ize of crew on a part could re ult in damage to the crew or the part.
A
A1:Backrest A2: Seat A3: Armrests
B
DMechanism,
1
EHydraulic
Gas Lift, 1
F
CStar Base, 1
H
Caster, 5
I
Hole Covers, 4
M6 20mm, 4
In ert the ca ter (B) into the leg of
the ba e (C) u ing pre ure, then
place the ga lift (E) in the middle of the
ba e, and cover it with (H) a hown.
Place the Back/Seat/Armre t (A)
( till folded down) with it front facing
away from you a hown. U ing crew (F),
a emble the mechani m (D) to the eat
with it handle facing to your LEFT.
Unfold the backre t, and ecure it to the top hole of the armre t u ing crew (G).
NOTE: Only one crew (G) on each ide, and only for the top hole.
Place the top over the ba e making
ure the tip of the ga lift enter into
the hole of the mechani m.
In ert the hole cover (H) on both
ide of the armre t .
(BACK OF CHAIR)
(Mechanism)
(Armrests to Backrest)
Allen Wrench, 1 (RIGHT
ARMREST) Tighten well all the crew before you
it on the chair for the fir t time.
NOTES:
These parts come pre-assembled, however, the
individual components can be removed and
replaced by disassembling where the screws
hold the parts together.
GM6 25mm, 2
(Armrests)
(1 crew,
Top hole,
each ide)
When you are
seated on the chair,
not looking at it.
RIGHT LEFT
A1 A2 A3
(LEFT
ARMREST)

CHAIR’S FUNCTIONS:
(1) To raise or lower the chair’s height, pull UP the lever that is under the seat. The chair goes down while
sitting on it, or up if you lift your body.
(2) To make the chair tilt, pull the same lever OUT horizontally to unlock this function, and IN to lock again.
(3) To adjust the tension for the tilting function, turn the mechanism’s knob in either direction to apply more
or less tension.
(4) To adjust the armrest height, push the button that is on the side of the armrest and release it once the
desired height is reached.
NOTE:
This chair does not have a folding-down function for daily use. It can be folded down for
transportation or storage during a long period of time, but it requires disassembling the
backrest from the top screw on both sides. If doing this, please remember to save the screws.
WARNINGS:
•Do not stand up on the chair or use it as ladder.
•Use the chair to seat only one person at a time.
•Do not use the chair if parts are damaged or if screws are loose or missing.
•Do not seat near the edge of the seat and always sit properly on the chair to avoid going beyond your balance point and fall off the chair.
•The chair is intended for teenagers and adults. If small children are using the chair, please keep close observation on them.
•Do not allow small children to play with the chair.
•Not paying attention to these warnings could result in severe injuries.
CARE AND MAINTENANCE:
•To clean the chair it is recommended to use a soft cloth lightly damped in a solution of smooth soap and water, then dry with a clean
towel.
•Do not use solvents or abrasive materials to clean any part of the chair.
•Before applying a cleaning agent, test on a small hidden area of the chair, like underneath the seat.
•Do not e pose the product to direct sunlight or to e treme environmental conditions.
•Every 4 months, inspect the chair completely and make sure that all screws are tighten.
(1)/(2)
(3)
(4)