Technogym Group Cycle D92 How to use

New Group Cycle (D92)




The information in this manual is intended for QUALIFIED TECHNICAL PERSONNEL, who
have been specically trained by TECHNOGYM S.p.A. and are qualied to carry out ne tuning
and start-up of the equipment, as well as major maintenance work and repairs, requiring in-depth
understanding of the equipment, how it works, its safety devices and maintenance procedures.
READ ALL THE INFORMATION IN THIS DOCUMENT VERY CAREFULLY BEFORE
CARRYING OUT ANY SERVICE WORK ON THE EQUIPMENT.
DANGEROUS VOLTAGE LEVELS
EVEN WHEN THE EQUIPMENT IS
SWITCHED OFF
NOTE: The information contained in this document can be changed without notice.
This document contains proprietary information that is covered by copyright. All rights reserved.
No part of this document may be photocopied, reproduced or translated into another language
without the prior wrien consent of Technogym S.p.A.
Technogym® is a trademark owned by Technogym S.p.A.
Document uncontrolled when printed.
New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed Page 3

Blank page.
New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed
Page 4

New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed Page 5
Table of Contents
1. GENERAL WARNINGS........................................................................................................ 13
1.1 INTRODUCTION ................................................................................... 13
1.2 USEFUL ADVICE .................................................................................... 14
1.3 GENERAL REGULATIONS REGARDING SERVICE WORK
14
1.3.1 PERSONAL PROTECTIVE EQUIPMENT ..........................................................14
2. TECHNICAL SPECIFICATIONS..................................................................................... 15
2.1 MECHANICAL CHARACTERISTICS .......................................... 16
2.1.1 OVERALL DIMENSIONS OF THE EQUIPMENT...........................................16
2.1.2 DIMENSIONS AND WEIGHT OF PACKAGING .............................................17
2.2 ENVIRONMENTAL CHARACTERISTICS................................. 18
2.3 COMPLIANCE WITH REGULATIONS........................................ 18
2.4 EQUIPMENT CODING........................................................................ 19
2.4.1 CODING FOR THE GROUP CYCLE EQUIPMENT WITH THE OLD WI-
FI CONSOLE AND GROUP CYCLE WITHOUT CONSOLE ........................19
2.4.2 CODING FOR GROUP CYCLE EQUIPMENT WITH THE NEW WI-FI /
ANT+ CONSOLE ..........................................................................................................20
2.5 SERIAL NUMBER STRUCTURE...................................................... 21
2.5.1 NEW SERIAL NUMBER STRUCTURE FOR GROUP CYCLES PRO-
DUCED STARTING FROM 2017.............................................................................21
2.5.2 SERIAL NUMBER STRUCTURE FOR GROUP CYCLES PRODUCED
PRIOR TO 2017..............................................................................................................22
2.6 POSITION OF MANUFACTURER AND PRODUCT IDENTI-
FICATION LABEL - POSITION OF WARNING LABEL ....... 23
2.7 CABLE DIAGRAM (CONNECT VERSION) ............................... 24
2.7.1 OLD ELECTRONICS CABLE DIAGRAM (REV. 1)...........................................24
2.7.2 NEW ELECTRONICS CABLE DIAGRAM (REV. 2)..........................................25
2.7.3 CABLE TABLE...............................................................................................................26
2.7.3.1 CABLES USED IN THE OLD AND NEW ELECTRONICS ................................................... 26
2.7.3.2 CABLES USED IN THE NEW ELECTRONICS.........................................................................26
3. OPERATING PRINCIPLE ................................................................................................... 29
3.1 ELECTRONIC COMPONENTS ........................................................ 29
3.1.1 GENERATOR.................................................................................................................29
3.1.2 VOLTAGE CONVERTER (TRANSFORMER).....................................................29
3.1.3 WATT SENSOR BOARD............................................................................................29
3.1.4 HALL SENSOR..............................................................................................................30

New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed
Page 6
3.1.5 CONSOLE (CONNECT VERSION)........................................................................30
3.1.5.1 OLD WI-FI CONSOLE .......................................................................................................................30
3.1.5.2 NEW WI-FI /ANT+ CONSOLE........................................................................................................ 31
3.1.6 NFC (CONNECT VERSION)....................................................................................31
3.1.7 BLUETOOTH SMART (CONNECT VERSION).................................................31
3.1.8 WIFI (CONNECT VERSION)...................................................................................32
4. ACCESSORIES......................................................................................................................... 33
5. MOVING AND INSTALLING THE EQUIPMENT.................................................. 35
5.1 INSTALLATION SPECIFICATIONS AND REQUIRE-
MENTS ......................................................................................................... 35
5.2 LIFTING AND MOVING THE EQUIPMENT............................ 36
6. TROUBLESHOOTING ......................................................................................................... 37
6.1 PROCEDURE TO FOLLOW WHEN REPLACING COMPO-
NENTS.......................................................................................................... 37
6.1.1 REPLACING THE GENERATOR / THE VOLTAGE CONVERTER ...........37
6.1.2 REPLACING THE FLYWHEEL ALUMINIUM DISC AND BRAKE CALLI-
PER....................................................................................................................................37
6.1.3 REPLACING THE WATT SENSOR BOARD ......................................................37
6.1.4 REPLACING THE HALL SENSOR /BRAKE FRAME......................................37
6.1.5 REPLACING THE CONSOLE..................................................................................38
6.1.6 REPLACING A COMPONENT THAT INTERACTS WITH THE BRAKING
SYSTEM (E.G. KNOB, ETC.).....................................................................................38
6.1.7 REPLACING THE GUIDES......................................................................................38
6.2 COMBO KEYPAD.................................................................................... 40
6.3 TROUBLESHOOTING ......................................................................... 42
6.3.1 THE CONSOLE DOES NOT TURN ON...............................................................42
6.3.2 MALFUNCTION CASES: RPM - WATT - LEVEL..............................................43
6.3.2.1 TROUBLESHOOTING CASE 1.......................................................................................................44
6.3.2.2 TROUBLESHOOTING CASE 2.......................................................................................................44
6.3.2.3 TROUBLESHOOTING CASE 3.......................................................................................................44
6.3.2.4 TROUBLESHOOTING CASE 4.......................................................................................................45
6.3.2.5 TROUBLESHOOTING CASE 5.......................................................................................................45
6.3.3 USER NOT ABLE TO LOGIN / LOGIN ICON FLASHING............................46
6.3.3.1 LOGIN VIA THE QR CODE - LOGIN VIA TGS/NFC..............................................................46
6.3.4 AFTER REPLACING THE WATT SENSOR BOARD, THE CONSOLE
DOES NOT TURN ON /THE RPM VALUES SHOWN ON THE DISPLAY
ARE TOO HIGH............................................................................................................48
6.3.5 LOOSENING OF THE FLYWHEEL SCREWS ....................................................49
6.3.6 LACK OF PRECISION IN THE WATT VALUES SHOWN ON THE DIS-
PLAY .................................................................................................................................49

New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed Page 7
6.3.7 PLAYS OF THE HANDLEBAR ASSEMBLY...................................................... 50
6.3.8 PLAYS OF THE SEAT HORIZONTAL SLIDER ................................................ 53
6.4 GUIDELINE ABOUT THE REPLACING OF THE FLYWHEEL
ALUMINIUM DISC AND BRAKE CALLIPER .......................... 56
6.5 BRAKE CALIBRATION ....................................................................... 56
6.5.1 CHECKING THE ALIGNMENT BETWEEN THE HOLE AND THE TOOTH
OF THE KNOB...............................................................................................................57
6.5.2 CHECKING THE CALIBRATION TEMPLATE .................................................59
6.5.3 MECHANICAL REGULATION OF THE BRAKE POSITION ......................61
6.5.4 SOFT CALIBRATION OF THE BRAKE................................................................64
6.6 PROCEDURE FOR REPLACING THE WATT SENSOR ID
BOARD ON GROUP CYCLES FIT WITH REV. 2 ELECTRON-
ICS.................................................................................................................. 66
6.7 PROCEDURE TO FOLLOW IF IT IS NECESSARY TO RE-
MOVE THE PLATE ON WHICH THE WATT SENSOR ID IS
FIXED............................................................................................................ 70
6.8 DIAGNOSTICS OF THE NEW WI-FI/ANT+ CONSOLE VIA THE NRF
CONNECT APP (BLE SIGNAL CHECK)........................................... 73
6.9 EQUIPMENT TESTING AFTER THE INTERVENTION OF TECHNI-
CAL SERVICE .................................................................................... 80
7. SW UPGRADE .......................................................................................................................... 83
7.1 SW UPGRADE FOR THE OLD WI-FI CONSOLE..................... 83
7.2 SOFTWARE UPGRADE FOR THE NEW WI-FI / ANT+ CON-
SOLE.............................................................................................................. 84
8. GROUP CYCLE CLASS ........................................................................................................ 87
8.1 REQUIREMENTS FOR CONFIGURING CLASS..................... 87
8.2 GROUP CYCLE CLASS CONFIGURATION.............................. 87
8.3 CONFIGURING THE GROUP CYCLE APP AS THE MAIN
UNITY SELF APP................................................................................... 100
8.4 SECOND NETWORK CONFIGURATION ................................ 100
9. EXECUTABLE SW FOR DIAGNOSTICS WITH PC : TERMINAL.................. 103
9.1 ACCESSING THE TERMINAL SW............................................... 103
9.2 STRUCTURE FOR ENTERING COMMANDS ........................ 104
9.2.1 READING FIRMWARE VERSIONS ....................................................................105
9.2.1.1 (CPU) FIRMWARE VERSION .......................................................................................................105
9.2.1.2 BLE /ANT+ MODULE FIRMWARE VERSION ......................................................................105
9.2.1.3 (WI-FI) FIRMWARE VERSION .....................................................................................................105

New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed
Page 8
9.2.1.4 (BETTER KEYPAD) FIRMWARE VERSION.......................................................................105
9.2.1.5 WATT SENSOR FIRMWARE VERSION ...............................................................................106
9.2.2 READING AND WRITING THE SERIAL NUMBERS AND IDENTIFI-
CATION PARAMETERS.......................................................................................106
9.2.2.1 WRITING THE CONSOLE SERIAL NUMBER..................................................................106
9.2.2.2 READING THE CONSOLE SERIAL NUMBER......................................................................106
9.2.2.3 SETTING THE FACILITY URL ....................................................................................................106
9.2.2.4 VIEWING THE FACILITY URL....................................................................................................107
9.2.2.5 WRITING THE LOW KIT SERIAL NUMBER..........................................................................107
9.2.2.6 READING THE LOW KIT SERIAL NUMBER.........................................................................107
9.2.2.7 DETERMINING MAC ADDRESS ...............................................................................................107
9.2.2.8 WRITING THE BICYCLE NUMBER...........................................................................................107
9.2.2.9 READING THE BICYCLE NUMBER..........................................................................................108
9.2.3 WI-FI AND NETWORK CONFIGURATION ....................................................108
9.2.3.1 ENTERING A NAME FOR THE NETWORK ...........................................................................108
9.2.3.2 WRITING THE NETWORK PASSWORD .................................................................................108
9.2.3.3 WRITING THE WEP KEY NUMBER.......................................................................................... 109
9.2.3.4 CHECKING CONNECTION TYPE ............................................................................................. 109
9.2.3.5 WRITING THE CONSOLE IP ADDRESS .................................................................................109
9.2.3.6 WRITING THE GATEWAY ADDRESS.......................................................................................110
9.2.3.7 CHECKING THE IP ADDRESS - DEFAULT GATEWAY - NETMASK............................ 110
9.2.3.8 READING THE WI-FI POWER.....................................................................................................110
9.2.4 CONFIGURING UNITY SELF...............................................................................110
9.2.4.1 SETTING PARAMETERS...............................................................................................................110
9.2.4.2 SETTING THE DATA SEND PERIOD.......................................................................................111
9.2.4.3 DISPLAYING THE REALTIME MONITOR CONFIGURATION.....................................111
9.2.4.4 ENABLING DATA SENDING .......................................................................................................111
9.2.4.5 DISABLING DATA SENDING...................................................................................................... 111
9.2.5 CONFIGURING DATE AND TIME .....................................................................112
9.2.5.1 RTC INITIALISATION....................................................................................................................112
9.2.5.2 SETTING THE DATE AND TIME ...............................................................................................112
9.2.5.3 READING THE DATE AND TIME..............................................................................................113
9.3 PROCEDURE FOR READING AND SETTING THE GEAR
RATIO (GENERATOR) ON THE WATT SENSOR BOARD 113
9.4 PROCEDURE FOR SETTING THE DATE AND TIME......... 115
10. EQUIPMENT SOFTWARE LOADER ........................................................................... 117
10.1 STEPS NECESSARY FOR ACCESSING THE EQUIPMENT
SOFTWARE LOADER PROGRAM................................................ 117
10.2 WATT SENSOR BOARD SW LOADING.................................... 118
10.2.1 WATT SENSOR TONIC (OLD ELECTRONICS REV. 1)................................120
10.2.2 WATT SENSOR ID (NEW ELECTRONICS REV. 2) ........................................122
10.3 WATT SENSOR BOARD PROGRAMMING............................. 123

New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed Page 9
10.3.1 PROGRAM WATT SENSOR BOARD..................................................................126
10.3.2 WRITE SERIAL NUMBER ......................................................................................126
10.3.3 WRITE TORQUE TABLE.........................................................................................126
10.3.4 COMPARE BRAKE CALIBRATION ....................................................................127
10.3.5 READ GENERATOR MODEL................................................................................129
10.3.6 WRITE GENERATOR MODEL..............................................................................129
10.3.7 READ TORQUE TABLE...........................................................................................129
11. DISASSEMBLY ...................................................................................................................... 131
11.1 REMOVING THE CONSOLE .......................................................... 131
11.1.1 REMOVING THE CONSOLE WITH VELCRO ................................................132
11.1.2 REMOVING THE CONSOLE WITH PROJECTIONS ..................................137
11.2 REMOVING AND ASSEMBLING THE PEDAL ..................... 139
11.2.1 REMOVING THE PEDAL CAGE..........................................................................141
11.3 REMOVING GUARDS ....................................................................... 142
11.3.1 REMOVING BRAKE GUARDS .............................................................................142
11.3.2 REMOVING THE MAIN RIGHT GUARD.........................................................144
11.3.3 REMOVING THE MAIN LEFT GUARD ............................................................147
11.3.4 REMOVING THE MUDGUARD PROTECTION............................................150
11.4 REMOVING THE PEDAL CRANKS............................................. 152
11.4.1 REMOVING THE RIGHT PEDAL CRANK.......................................................152
11.4.2 REMOVING THE LEFT PEDAL CRANK...........................................................154
11.4.3 REPLACING THE RIGHT AND LEFT PEDAL CRANK...............................156
11.5 BELTS AND FLYWHEEL .................................................................... 157
11.5.1 TIGHTENING THE TRANSMISSION BELT ...................................................157
11.5.2 REMOVING THE BELT TENSIONER ................................................................159
11.5.3 REMOVING THE FLYWHEEL, TRANSMISSION BELT AND GENERA-
TOR BELT .....................................................................................................................160
11.5.4 REMOVING THE BRAKE ASSEMBLY...............................................................166
11.5.5 REMOVING THE KNOB..........................................................................................168
11.6 HANDLEBAR.......................................................................................... 170
11.6.1 REMOVING THE HANDLEBAR ..........................................................................170
11.6.2 DISASSEMBLING THE HANDLEBAR’S HORIZONTAL SLIDER AS-
SEMBLY.........................................................................................................................171
11.6.3 DISASSEMBLING THE HANDLEBAR’S VERTICAL SLIDER .................174
11.6.4 REMOVING SLEEVE BUSHINGS AND REGULATION THE POST ......181
11.6.5 FITTING THE HANDLEBAR’S VERTICAL SLIDER BACK ONTO THE
BIKE ...............................................................................................................................183
11.7 SEAT ............................................................................................................ 186

New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed
Page 10
11.7.1 REMOVING THE SEAT ...........................................................................................186
11.7.2 DISASSEMBLING THE SEAT’S HORIZONTAL SLIDER ASSEMBLY ..187
11.7.3 DISASSEMBLING THE SEAT’S VERTICAL SLIDER...................................191
11.7.4 REMOVING SLEEVE BUSHINGS AND REGULATION THE POST ......196
11.7.5 DISASSEMBLING THE SEAT’S GUARD..........................................................198
11.8 DISASSEMBLING THE OLD ELECTRONICS (REV. 1) ...... 202
11.9 REMOVING THE GENERATOR.................................................... 203
12. TIGHTENING TORQUES -GREASE -ADHESIVES & SEALANTS - BELT TEN-
SIONING .................................................................................................................................. 207
12.1 PEDAL ....................................................................................................... 207
12.2 PEDAL CRANK ...................................................................................... 208
12.3 TRANSMISSION BELT...................................................................... 209
12.4 FLYWHEEL ............................................................................................... 209
12.5 LEVER OF HANDLEBAR AND SEAT.......................................... 210
12.5.1 SELF-LOCKING NUT ...............................................................................................210
12.5.2 PIN...................................................................................................................................211
13. ADJUSTMENTS AND REGULATIONS ..................................................................... 213
13.1 ADJUSTMENT ....................................................................................... 213
13.2 BELT TENSION REGULATION..................................................... 213
13.3 PLAY REGULATION FOR VERTICAL REGULATIONS .... 215
13.4 PLAY REGULATION FOR HORIZONTAL REGULATIONS..
217
14. PRODUCT MODIFICATIONS ....................................................................................... 219
14.1 NEW WI-FI / ANT+ CONSOLE......................................................... 219
14.1.1 OPERATING PRINCIPLE.......................................................................................219
14.1.2 HOW TO IDENTIFY THE TYPE OF CONSOLE INSTALLED ON THE
GROUP CYCLE (D92)................................................................................................219
14.1.3 CONSOLE UPGRADE: ASSEMBLY OF THE NEW WI-FI / ANT+ CON-
SOLE ON THE NEW GROUP CYCLE (D92) WITH THE OLD WI-FI CON-
SOLE INSTALLED.....................................................................................................219
14.1.3.1 COMPATIBILITY WITH THE GC WITH THE NEW ELECTRONICS (REV.2)AND THE
OLD ELECTRONICS (REV.1) ........................................................................................................219
14.1.3.2 INSTALLING THE NEW WI-FI / ANT+ CONSOLE ON THE NEW GROUP CYCLE
(D92)........................................................................................................................................................220
14.1.4 CONSOLE DOWNGRADE: ASSEMBLY OF THE OLD WI-FI CONSOLE
ON THE NEW GROUP CYCLE (D92)WITH THE NEW WI-FI /ANT+ CON-
SOLE INSTALLED.....................................................................................................220
14.1.5 SOFTWARE UPGRADE FOR THE NEW WI-FI /ANT+ CONSOLE .........220
14.1.6 COMMANDS FROM THE TERMINAL .............................................................220

New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed Page 11
14.1.7 EQUIPMENT SETUP APP......................................................................................220
14.2 ELECTRONICS IN THE GROUP CYCLE CONNECT VER-
SION............................................................................................................ 221
14.2.1 ELECTRONICS REV.1..............................................................................................221
14.2.2 ELECTRONICS REV.2..............................................................................................221
14.3 INTRODUCTION OF THE PROTECTION GUTTER........... 222
14.4 INSERTING THE BELLEVILLE WASHER ON THE FRONT
AND REAR HANDLE.......................................................................... 222
14.5 NEW FOOT THAT DOES NOT STAIN THE FLOOR............ 223
15. PLANNED MAINTENANCE ........................................................................................... 225
16. LIST OF CHANGES FOR MANUAL REVISION ................................................... 227
16.1 REVISION 2.0.......................................................................................... 227
16.2 REVISION 3.0.......................................................................................... 227
16.3 REVISION 4.0.......................................................................................... 228
16.4 REVISION 4.1.......................................................................................... 228
16.5 REVISION4.2........................................................................................... 229
16.6 REVISION 4.3.......................................................................................... 229
16.7 REVISION 4.4.......................................................................................... 229
16.8 REVISION 5.0.......................................................................................... 229
16.9 REVISION 5.1.......................................................................................... 230

New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed
Page 12

1. GENERAL WARNINGS
1.1 INTRODUCTION
This document has been prepared specically for Technogym After Sales Service, with the aim
of providing authorised personnel with the information for carrying out maintenance and repair
operations in the correct manner.
A thorough understanding of the technical data contained herein is absolutely fundamental in
order for the operator to achieve the highest level in professional training.

 
CAUTION: Regulation that may lead to damage to the equipment if not complied with.
WARNING: Information regarding the operation in progress.
Detail regarding the operation in progress.
New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed Page 13

1.2 USEFUL ADVICE
Technogym advises you to plan your technical assistance task in the following way:
Carefully assess the impressions reported by the Customer regarding the equipment’s operating
faults and ask questions suitable to clarify the signs of the defect.
Clearly diagnose the causes of the problem. This manual provides the fundamental theoretical ba-
sis, which must then be integrated by personal experience and aendance at the training courses
periodically oered by Technogym.
Plan the repair work in a rational manner so as to avoid wasting any time, e.g. collecting spare
parts, preparing tools and equipment etc.
Access the component to be repaired, avoiding any unnecessary operations. On this point, it will
be extremely helpful if you consult the disassembling sequences shown in this manual.
1.3 GENERAL REGULATIONS REGARDING SERVICE
WORK
1. Check the serial number of the equipment, comparing it with the one on the work order.
2. Always mark any parts or positions which may be confused with each other at the time of
reassembly.
3. Use original Technogym spare parts and lubricants of the recommended brands.
4. Use special tools where specied.
5. Consult the Technical Newsleers and News Flashes, which may contain more up-to-date
information on regulations and maintenance than those contained in this manual.
6. Before starting the repair procedure, make sure that the recommended tools are available and
in good condition.
7. For the procedures described in this manual, use only the specied tools.
 -

1.3.1 PERSONAL PROTECTIVE EQUIPMENT
For details, refer to the Health&Safety After Sales procedure, available on TG Direct.
New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed
Page 14

2. TECHNICAL SPECIFICATIONS

Pedals With pedal straps and SPD clips.
Minimum inclination angle for
movement 17°-19°
Flywheel
Molten cast iron, painted.
Aluminium disc for magnetic braking; anodized and painted.
Total weight: 17.4 kg.
Braking system Magnetic with permanent magnets.
Degree of protection IP20
Table 1
New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed Page 15

2.1 MECHANICAL CHARACTERISTICS
2.1.1 OVERALL DIMENSIONS OF THE EQUIPMENT
NEW GROUP CYCLE (D92)
DEVICE WEIGHT 67 kg - 148 lb
MAXIMUM USER WEIGHT 160 kg - 353 lb
Table 2
1340 mm
(53”)
1120 mm
(44”)
1060 mm
(42”)
590 mm
(23”)
1185 mm
(47”)
Figure 1
New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed
Page 16

2.1.2 DIMENSIONS AND WEIGHT OF PACKAGING
Several components of the bike have been disassembled for shipping purposes.
Disassembled components:
▪Handlebar
▪Pedals
▪Front and rear crosspieces (including relevant plastic covers)
DIMENSIONS (L x W x H) 1115 x 270 x 965 (mm)
44 x 10.5 x 38 (inch)
WEIGHT 74 kg - 163 lbs
Table 3
H
LW
Figure 2
New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed Page 17

2.2 ENVIRONMENTAL CHARACTERISTICS
Temperature In operation from +10° to +25°C
In storage from -10° to +70°C
Dampness In operation between 20% and 90%
In storage between 20% and 90%
Table 4
2.3 COMPLIANCE WITH REGULATIONS
 Fordetailsaboutthedirectives,regulationscoveredbytheequipmentandcertications/Declara-
tions of Conformity, contact the Technogym technical Support Service.
New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed
Page 18

2.4 EQUIPMENT CODING
The structure of the equipment code for the New Group Cycle (D92) with the old WI-FI con-
sole isdierentthantheequipmentcodefortheNew Group Cycle (D92) with the new WI-FI /
ANT+ code, as described below.
2.4.1 CODING FOR THE GROUP CYCLE EQUIPMENT
WITH THE OLD WI-FI CONSOLE AND GROUP CYCLE
WITHOUT CONSOLE
The equipment code for the New Group Cycle (D92) with the old WI-FI console and the New
Group Cycle (D92) without a console, is an alphanumerical code that is structured as follows:
Charac-
ters Description Values and meaning
1,2,3 Line D92 = Group Cycle
4, Product version B= Ride (no console)
C= Connect
5, Transmission type B= Belt Transmission
6, Clutch N= None
7, Localisation; E= World
8, Certication 0= None
9, - -
10,11 Frame colour DL = Yellow
DM = Light grey
12,13 Seat 02 = Type 2 “Velo” black
14,15 Guard colour NR = Black
Table 5
New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed Page 19

2.4.2 CODING FOR GROUP CYCLE EQUIPMENT WITH THE
NEW WI-FI / ANT+ CONSOLE
The equipment code for the New Group Cycle (D92) with the new WI-FI / ANT+ console, is an
alphanumerical code that is structured as follows:
In particular, the leer A was added to the end position in the equipment code.
Charac-
ters Description Values and meaning
1,2,3 Line D92 = Group Cycle
4, Product version C= Connect
5, Transmission type B= Belt Transmission
6, Clutch N= None
7, Localisation; E= World
8, Certication 0= None
9, - -
10,11 Frame colour DL = Yellow
DM = Light grey
12,13 Seat 02 = Type 2 “Velo” black
14,15 Guard colour NR = Black
16 Console A = New WI-FI / ANT+ console
Table 6
New Group Cycle (D92):
Technical Service Guide - Rev. 5.1
Document uncontrolled when printed
Page 20