Tektronix A6304XL User manual

Instructions
A6304XL
500 Amp AC/DC Current Probe
070-8939-02
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
Advanced Test Equipment Rentals
www.atecorp.com 800-404-ATEC (2832)
®
E
s
t
a
b
l
i
s
h
e
d
1
9
8
1

Copyright ©Tektronix, Inc. All rights reserved.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
Tektronix, Inc., P.O. Box 1000, Wilsonville, OR 97070–1000
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.

WARRANTY
Tektronix warrants that the products that it manufactures and sells will be free from defects in materials and
workmanship for a period of one (1) year from the date of shipment. If a product proves defective during this
warranty period, Tektronix, at its option, either will repair the defective product without charge for parts and labor,
or will provide a replacement in exchange for the defective product.
In order to obtain service under this warranty, Customer must notify Tektronix of the defect before the expiration
of the warranty period and make suitable arrangements for the performance of service. Customer shall be
responsible for packaging and shipping the defective product to the service center designated by Tektronix, with
shipping charges prepaid. Tektronix shall pay for the return of the product to Customer if the shipment is to a
location within the country in which the Tektronix service center is located. Customer shall be responsible for
paying all shipping charges, duties, taxes, and any other charges for products returned to any other locations.
This warranty shall not apply to any defect, failure or damage caused by improper use or improper or inadequate
maintenance and care. Tektronix shall not be obligated to furnish service under this warranty a) to repair damage
resulting from attempts by personnel other than Tektronix representatives to install, repair or service the product;
b) to repair damage resulting from improper use or connection to incompatible equipment; c) to repair any
damage or malfunction caused by the use of non-Tektronix supplies; or d) to service a product that has been
modified or integrated with other products when the effect of such modification or integration increases the time
or difficulty of servicing the product.
THIS WARRANTY IS GIVEN BY TEKTRONIX IN LIEU OF ANY OTHER WARRANTIES, EXPRESS
OR IMPLIED. TEKTRONIX AND ITS VENDORS DISCLAIM ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TEKTRONIX’
RESPONSIBILITY TO REPAIR OR REPLACE DEFECTIVE PRODUCTS IS THE SOLE AND
EXCLUSIVE REMEDY PROVIDED TO THE CUSTOMER FOR BREACH OF THIS WARRANTY.
TEKTRONIX AND ITS VENDORS WILL NOT BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES IRRESPECTIVE OF WHETHER TEKTRONIX OR
THE VENDOR HAS ADVANCE NOTICE OF THE POSSIBILITY OF SUCH DAMAGES.

Contacting Tektronix
Product
Support For questions about using Tektronix measurement products, call toll free in North America:
1-800-TEK-WIDE (1-800-835-9433 ext. 2400)
6:00 a.m. – 5:00 p.m. Pacific time
Or contact us by e-mail:
[email protected]
For product support outside of North America, contact
your local Tektronix distributor or sales office.
Service
Support Tektronix offers extended warranty and calibration programs as options on many products. Contact your
local Tektronix distributor or sales office.
For a listing of worldwide service centers, visit our web
site.
For other
informa-
tion
In North America:
1-800-TEK-WIDE (1-800-835-9433)
An operator will direct your call.
To write us
Website
Tektronix, Inc.
P.O. Box 1000
Wilsonville, OR 97070-1000
USA
Tektronix.com

A6304XL Instructions i
Table of Contents
General Safety Summary ii. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service Safety Summary iv. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Getting Started 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Probe Installation 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating the Current Probe Slide 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Degaussing and Autobalancing the Current Probe 3. . . . . . . . . . . . . . . . . . . . . . .
Why Degauss the Current Probe? 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maximum Current Limits 4. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Specifications 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Maintenance 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cleaning 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disassembly Instructions 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Obtaining Replacement Parts 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Preparation for Shipment 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Replaceable Parts List 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parts Ordering Information 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Using the Replaceable Parts List 15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

ii A6304XL Instructions
General Safety Summary
Review the following safety precautions to avoid injury and prevent damage to
this product or any products connected to it. To avoid potential hazards, use this
product only as specified.
Only qualified personnel should perform service procedures.
Connect and Disconnect Properly. Do not connect or disconnect probes or test
leads while they are connected to a voltage source.
Ground the Product. This product is indirectly grounded through the grounding
conductor of the mainframe power cord. To avoid electric shock, the grounding
conductor must be connected to earth ground. Before making connections to the
input or output terminals of the product, ensure that the product is properly
grounded.
Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings
and marking on the product. Consult the product manual for further ratings
information before making connections to the product.
The common terminal is at ground potential. Do not connect the common
terminal to elevated voltages.
Do Not Operate Without Covers. Do not operate this product with covers or panels
removed.
Avoid Exposed Circuitry. Do not touch exposed connections and components
when power is present.
Do Not Operate With SuspectedFailures. If you suspect there is damage to this
product, have it inspected by qualified service personnel.
Do Not Operate in Wet/DampConditions.
Do Not Operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
To Avoid Fire or
Personal Injury

General Safety Summary
A6304XL Instructions iii
Terms in this Manual. These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
Terms on the Product. These terms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read the
marking.
WARNING indicates an injury hazard not immediately accessible as you read the
marking.
CAUTION indicates a hazard to property including the product.
Symbols on the Product. The following symbols may appear on the product:
ProtectiveGround
(Earth)Terminal CAUTION Refer to Manual Double Insulated
WARNING
High Voltage
Symbols and Terms

iv A6304XL Instructions
Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary before performing any service
procedures.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.

A6304XL Instructions 1
Getting Started
This section covers the installation and operation of the A6304XL with the
AM 503B and AM 5030 amplifiers. The probe does not need to be matched to a
dedicated amplifier for operation or calibration.
The A6304XL is a DC to 2 MHz current probe designed for use with the
AM 503B and AM 5030 current probe amplifiers. The A6304XL can measure
currents to 500 A (DC + peak AC), and up to 700 A peak current (while not
exceeding the amp-second rating).
The A6304XL can only be used with the AM 503B and AM 5030 and will not
be recognized by other current probe amplifiers.
NOTE. If the A6304XL is not recognized by your AM503B or AM5030, contact
your nearest Tektronix Service Center concerning an amplifier firmware
upgrade.
Please refer to the amplifier documentation for verification procedures, adjust-
ments, and additional specifications.
If you need assistance using your probe, please call our Customer Support Center
at 1-800-TEK-WIDE (1-800-835-9433). If you are outside the United States or
Canada, please contact your nearest Tektronix Service Center.
Probe Installation
To connect a current probe to the Amplifier input connector, align the tab of the
probe connector with the slot in the Amplifier INPUT connector as shown in
Figure 1(a). Align the dot on the probe connector with the groove opening of the
input connector as shown in Figure 1(b). Push the probe connector in while
twisting the barrel clockwise to lock the connector.
CAUTION. Handle current probes with care. Do not drop a probe or subject it to
impact, or the core may crack. Do not connect or disconnect a current probe
while the probe is clamped around a live conductor or while the Amplifier is
powered on, or the probe may suffer electrical damage.

Getting Started
2A6304XL Instructions
Amplifier
Current Probe Connector
Amplifier Groove
Current Probe
Connector
Push connector in
and twist to lock
(a) Align the Tab With the Connector Slot (b) Insert the Connector Into the Amplifier
Alignment Dot
Slot
Tab
Figure 1: Connecting a Current Probe to the Amplifier
Operating the Current Probe Slide
Each current probe has a slide that opens and closes the probe jaw. This allows
you to clamp the probe around a conductor under test. The slide must be locked
to accurately measure current or to degauss the probe. If a probe is unlocked, the
PROBE OPEN indicator on the Amplifier will light.
WARNING. When the probe slides are open, the exposed ferrite core pieces are
not insulated.
To avoid injury or equipment damage, remove power from an uninsulated wire
before clamping the current probe around it.
Never disconnect the probe from the Amplifier when the probe is connected to a
live conductor.
Allow your hands to contact the probe handle and lock only.
Figure 2 illustrates the slide operation of the probe. To open the probe, press the
bottom of the lock button and squeeze the handle until the core is open. To lock
the probe, release the squeeze handle and press the top of the lock button.