Tektronix TH3000 Series Manual

xx
THS3000 Series
Oscilloscopes
Installation and Safety
ZZZ
Instructions
*P071296302*
071-2963-02

THS3000 Series
Oscilloscopes
Installation and Safety
ZZZ
Instructions
xx
Revision A
www.tek.com
071-2963-02

Copyright © Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries
or suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication
supersedes that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14150 SW Karl Braun Drive
P.O. Box 50 0
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
In North America, call 1-800-833-9200.
Worldwide, visit www.tek.com to find contacts in your area.

Table of Contents
Preface ............................................................................................................... 1
Accessories and Replaceable Parts .......................................................................... 1
Documentation................................................................................................. 4
General Safety Summary .......................................................................................... 5
To Avoid Electrical Shock or Fire ................................................................................ 7
If Safety Features Are Impaired................................................................................... 8
Compliance Information........................................................................................... 9
EMC Compliance.............................................................................................. 9
Safety Compliance............................................................................................ 11
Environmental Considerations .............................................................................. 13
Operating Requirements .......................................................................................... 15
Electrical Ratings ............................................................................................. 15
Environmental Ratings....................................................................................... 16
Physical Specifications....................................................................................... 16
Connectors.......................................................................................................... 17
Input Connectors.............................................................................................. 17
Getting Started ......... .......................... .......................... .......................... .............. 19
Battery Pack Safety Information............................................................................ 19
Battery Installation ........................................................................................... 22
AC Power Adapter Connection ............................................................................. 24
Power On and Power Off Procedures....................................................................... 25
Front Panel Controls.......................................................................................... 26
Functional Check ............................................................................................. 27
Take Floating Measurements................................................................................ 29
前言 ...................................................................................................... 31
附件和可更换部件 ................................................................................. 31
文档 .................................................................................................. 34
常规安全概要 ........................................................................................... 35
避免电击或火灾 ........................................................................................ 36
如果安全功能受损...................................................................................... 38
符合性信息 .............................................................................................. 39
EMC 符合性 .......................................................................................... 39
安全符合性.......................................................................................... 40
环境注意事项....................................................................................... 42
操作要求................................................................................................. 43
电气额定值.......................................................................................... 43
环境额定值.......................................................................................... 44
物理技术规格....................................................................................... 44
THS3000 Series Oscilloscopes Installation and Safety Instructions i

Table of Contents
连接器 ................................................................................................... 45
输入连接器.......................................................................................... 45
入门 ...................................................................................................... 47
电池组安全信息 .................................................................................... 47
电池安装 ............................................................................................ 49
交流电源适配器连接 .............................................................................. 52
开机和关机步骤 .................................................................................... 53
前面板控件.......................................................................................... 54
功能检查 ............................................................................................ 55
进行浮动测量....................................................................................... 57
まえがき .................................................................................................. 59
アクセサリと交換部品 ............................................................................... 59
マニュアル ........................................................................................... 63
安全にご使用いただくために .......................................................................... 64
感電や火災を避けるために ............................................................................ 66
安全機能を損なわないために.......................................................................... 67
適合性に関する情報.................................................................................... 68
EMC 適合性 ......................................................................................... 68
安全性 ............................................................................................... 7
0
環境への配慮 ....................................................................................... 72
動作の要件 .............................................................................................. 73
電気定格 ............................................................................................ 73
環境要件 ............................................................................................ 74
物理仕様 ............................................................................................ 74
コネクタ................................................................................................... 75
入力コネクタ......................................................................................... 75
はじめに.................................................................................................. 77
バッテリ・パックの安全に関する情報 .............................................................. 77
バッテリの取り付け .................................................................................. 80
AC 電源アダプタの接続............................................................................ 82
電源投入、電源切断の手順 ....................................................................... 83
フロント・パネル・コントロール ...................................................................... 84
機能チェック......................................................................................... 85
フローティング測定の実行 ......................................................................... 87
ii THS3000 Series Oscilloscopes Installation and Safety Instructions

Preface
This document contains the following information:
A list of standard and optional accessories
A list of replaceable parts
Important safety precautions to avoid injury and prevent damage to this
product or any products connected to it
EMC (electromagnetic compliance), safety, and environmental standards
with which the instrument complies
Voltage, power, and environmental requirements to use the product
Battery pack safety information and installation instructions
External power supply installation instructions
Power on and power-off procedures
Front panel controls description
Functional check procedure
Important safety information about taking floating measurements
Accessories and Replaceable Parts
The following tables contain a list of standard and optional accessories, and a
list of replaceable parts. What came standard with this instrument depends on
whether you ordered the base instrument or the kitted version (TK model). The
first table shows which accessories are standard and which are optional. Items that
are only standard for the kitted version are noted as such.
Unpack the instrument and check that you have received all of the items marked
in the table as standard accessories for your instrument configuration. If you
ordered optional accessories, check that those you ordered are in your shipment.
You may want to save the shipping carton and packing materials (including the
anti-static bag) in case you need to ship the instrument. Go to www.tek.com for
the most current information on accessories.
THS3000 Series Oscilloscopes Installation and Safety Instructions 1

Preface
Standard and Optional Accessories Standard Optional
Tektronix part
number
THS3000 SERIES OSCILLOSCOPE DOCUMENTATION KIT
This kit contains this printed manual (071-2963-XX) and a CD (063-4379-XX)
containing various user documents. (See page 4, Documentation.)
020-3086-xx
THS3000 SERIES OSCILLOSCOPE 7 HOUR LI-ION BATTERY THSBAT
EXTERNAL BATTERY CHARGER THSCHG
POWER SUPPLY; EXTERNAL AC-DC, ISOLATED, 100-260 VAC, 50-60 HZ,
IEC320-C14 CONNECTOR IN 18 V; SAFETY CONTROLLED
119-7900-xx
POWER CORD (See the International Power Cords list that follows this table for
the type of power cord included with your instrument.)
Not applicable
CABLE; USB-A TO MINI-USB-B FOR PC CONNECTION 174-6106-xx
HANDLE, CARRYING 367-0564-xx
HANDLE; STRAP, HANGING 367-0565-xx
HANDLE; HANGING HOOK 376-0255-xx
SOFT SIDED CARRYING CASE 1ACHHS
HARD SIDED CARRYING CASE 2HCHHS
PROBE; YELLOW 300 MHZ 10X PASSIVE THP0301-Y
PROBE; BLUE 300 MHZ 10X PASSIVE THP0301-B
PROBE; MAGENTA 300 MHZ 10X PASSIVE THP0301-M
PROBE; GREEN 300 MHZ 10X PASSIVE THP0301-G
CASE; SOFT CARRYING CASE FOR PROBES 2016-2050-xx
PROBE REPLACEMENT ACCESSORY KIT:
HOOK CLIP FOR PROBE TIP (Qty 1)
GROUND LEAD WITH ALLIGATOR CLIP (Qty 1)
GROUND SPRING FOR PROBE TIP (Qty 2)
INSULATION SLEEVE FOR PROBE TIP (Qty 2)
ADJUSTMENT TOOL (Qty 1)
METAL BNC ADAPTER (Qty 1)
2020-3085-xx
1Standard for non-TK models only
2Standard for TK models only
Replaceable parts Part number
THS3000 Series oscilloscopes hardware kit (all fasteners required to assemble instrument) 020-3101-xx
1/4-turn fastener (for battery access door) 200-5266-xx
Right input door (covers DC input jack) 437-0533-xx
Top holster/input panel 437-0534-xx
2 THS3000 Series Oscilloscopes Installation and Safety Instructions

Preface
International power cords. Your instrument was shipped with one of the following
power cord options. Power cords for use in North America are UL listed and CSA
certified. Cords for use in areas other than North America are approved by at least
one authority acceptable in the country to which the product is shipped.
Opt. A0 – North America power
Opt. A1 – Universal Euro power
Opt. A2–Uni
ted Kingdom power
Opt. A3 – Australia power
Opt. A5 – Switzerland power
Opt. A6 – Japan power
Opt. A10 – China power
Opt. A11 – India power
Opt. A12 – Brazil power
CAUTION. To reduce risk of fire and shock, use the certified power cord provided
with the product when using the product without battery power.
Service Options You can order the following service options for your instrument.
Option Tektronix part number
3yea
r calibration service C3
5ye
ar calibration service C5
Calibration data report D1
Service
options
5y
ear repair service R5
Extended
service
options
5 year repair service R5DW
THS3000 Series Oscilloscopes Installation and Safety Instructions 3

Preface
Documentation
The following table lists some of the documentation that is available for this
product and shows where you can find it: in a printed manual, on the product
documentation CD-ROM, or on the Tektronix Web site at www.tek.com.
Table 1: Product documentation
Item Purpose Location
Installation and Safety Instructions
(this manual)
Provides safety and compliance information with
hardware installation instructions to present the
associated safety warnings. This manual is available
in English, Japanese, and Simplified Chinese.
Printed manual and also available
in electronic format on the
product documentation CD and at
www.tek.com/manuals
User Manual Provides operation, application, and specifications
information. This manual is available in English,
French, German, Spanish, Italian, Portuguese, Korean,
Japanese, Simplified Chinese, Traditional Chinese,
and Russian.
Product documentation CD and
available at www.tek.com/manuals
Performance Verification Technical
Reference
Performance verification procedures for checking
instrument performance.
Product documentation CD and
available at www.tek.com/manuals
THP0301 Voltage Probe
Instructions
Provides information about using the THP0301 probe
with the instrument.
Printed manual and also available
in electronic format on the product
documentation CD and available
at www.tek.com/manuals
THSCHG External Battery Charger
Instructions
Provides information about how to use the battery
charger with this instrument.
Printed manual and also available
in electronic format on the product
documentation CD and available
at www.tek.com/manuals
THSBAT Rechargeable Battery
Pack Instructions
Provides information about how to use the battery with
this instrument.
Printed manual and also available
in electronic format on the product
documentation CD and available
at www.tek.com/manuals
119-7900-XX AC Adapter/Power
Supply Instructions
Provides information about how to use the external
power supply with this instrument.
Printed manual and also available
in electronic format on the product
documentation CD and available
at www.tek.com/manuals
4 THS3000 Series Oscilloscopes Installation and Safety Instructions

General Safety Summary
General SafetySummary
This manual contains information and warnings that must be followed by the
user to ensure safe operation and to keep the instrument in a safe condition. Use
of this equipment in a manner not specified by the manufacturer may impair
protection provided by the equipment.
Review the following safety precautions to avoid injury and prevent damage to
this product or any products connected to it.
To avoid potential hazards, use this product only as specified.
Only qualified personnel should perform service procedures.
To Avoid Fire or Personal
Injury
Use Proper Power Cord. Use only the power cord specified for this product and
certified for the country of use.
Connect and Disconnect Properly. Do not connect or disconnect probes or test
leads while they are connected to a voltage source.
Connect and Disconnect Properly. Connect the probe output to the measurement
instrument before connecting the probe to the circuit under test. Connect the
probe reference lead to the circuit under test before connecting the probe input.
Disconnect the probe input and the probe reference lead from the circuit under test
before disconnecting the probe from the measurement instrument.
Observe All Terminal Ratings. To avoid fire or shock hazard, observe all ratings
and markings on the product. Consult the product manual for further ratings
information before making connections to the product.
Do not apply a potential to any terminal, including the common terminal, that
exceeds the maximum rating of that terminal.
Power Disconnect. The power cord disconnects the product from the power
source. Do not block the power cord; it must remain accessible to the user at
all times.
Do Not Operate Without Covers. Do not operate this product with covers or
panels removed.
Do Not Operate With Suspected Failures. If you suspect that there is damage to
this product, have it inspected by qualified service personnel.
Avoid Exposed Circuitry. Do not touch exposed connections and components
when power is present.
Replace Batteries Properly. Replace batteries only with the specified type and
rating.
THS3000 Series Oscilloscopes Installation and Safety Instructions 5

General Safety Summary
Recharge Batteries Properly. Recharge batteries for the recommended charge
cycle only.
Use Proper AC Adapter. Use only the AC adapter specified for this product.
Do Not Operate in Wet/Damp Conditions.
Do Not Operate in an Explosive Atmosphere.
Keep Product Surfaces Clean and Dry.
TermsinthisManual These terms may appear in this manual:
WARNING. Warning statements identify conditions or practices that could result
in injury or loss of life.
CAUTION. Caution statements identify conditions or practices that could result in
damage to this product or other property.
Isolated, electrically floating. The terms “isolated” or “electrically floating” are
used in this manual to indicate a measurement in which the product input BNC is
connected to a voltage different from earth ground.
Working voltage. Voltage ratings that are mentioned in the warnings in this
manual are given as limits for “working voltage”. They represent V AC RMS
(50-60 Hz) for AC sine wave applications and as V DC for DC applications.
Symbols and Terms on the
Product
These terms may appear on the product:
DANGER indicates an injury hazard immediately accessible as you read
the marking.
WARNING indicates an injury hazard not immediately accessible as you
read the marking.
CAUTION indicates a hazard to property including the product.
The following symbol(s) may appear on the product:
6 THS3000 Series Oscilloscopes Installation and Safety Instructions

ToAvoidElectricalShockorFire
To Avoid Electrical Shock or Fire
WARNING. To avoid electrical shock or fire, if a product input is connected to
more than 42 V peak (30 VRMS) or 60 V DC, observe the following warnings:
Use only insulated voltage probes, test leads, and adapters supplied with the
product, or indicated by Tektronix as suitable for the THS3014 and THS3024
products.
Before use, inspect voltage probes, test leads and accessories for mechanical
damage and replace when damaged.
Remove all probes, test leads and accessories that are not in use.
Always connect the power adapter first to the ac outlet before connecting
it to the product.
Do not touch voltages >30 V AC RMS, 42 V AC peak, or 60 V DC.
Do not connect the ground spring to voltages higher than 42 V peak
(30 VRMS) from earth ground.
Do not apply more than the rated voltage between the terminals or between
each terminal and earth ground.
Do not apply input voltages above the rating of the instrument. Use caution
when using 1:1 test leads because the probe tip voltage will be directly
transmitted to the product.
Do not use exposed metal BNC connectors.
Do not insert metal objects into connectors.
Use the product only as specified, or the protection supplied by the product
can be compromised.
Carefully read all instructions.
Do not use the product if it operates incorrectly.
Do not use and disable the product if it is damaged.
Keep fingers behind the finger guards on the probes.
Use only correct measurement category (CAT), voltage, temperature, altitude,
and amperage rated probes, test leads, and adapters for the measurement.
Do not exceed the Measurement Category (CAT) rating of the lowest rated
individual component of a product, probe, or accessory.
Measure a known voltage first to make sure that the product operates correctly.
THS3000 Series Oscilloscopes Installation and Safety Instructions 7

If Safety Features Are Impaired
Examine the case before you use the product. Look for cracks or missing
plastic. Carefully look at the insulation around the terminals.
Do not work alone.
Comply with local and national safety codes. Use personal protective
equipment (approved rubber gloves, face protection, and flame resistant
clothes) to prevent shock and arc blast injury where hazardous live conductors
are exposed.
The battery door must be closed and locked before you operate the product.
Do not operate the product with covers removed or the case open. Hazardous
voltage exposure is possible.
Remove the input signals before you clean the product.
Use only specified replacement parts.
The isolated input connectors have no exposed metal and are fully insulated to
protect against electrical shock.
The BNC jacks can independently be connected to a voltage above earth ground
for isolated (electrically floating) measurements.
If Safety Features Are Impaired
Use of the product in a manner not specified may impair the protection provided
by the equipment.
Do not use test leads if they are damaged. Examine the test leads for damaged
insulation, exposed metal, or if the wear indicator shows.
Whenever it is likely that safety is impaired, the product must be turned off
and disconnected from the line power. The matter should then be referred
to qualified personnel. Safety is likely to be impaired if, for example, the
product fails to perform the intended measurements or shows visible damage.
8 THS3000 Series Oscilloscopes Installation and Safety Instructions

Compliance Information
Compliance Information
This section lists the EMC (electromagnetic compliance), safety, and
environmental standards with which the instrument complies.
EMC Compliance
EC Declaration of
Conformity – EMC
Meets intent of Directive 2004/108/EC for Electromagnetic Compatibility.
Compliance was demonstrated to the following specifications as listed in the
Official Journal of the European Communities:
EN 61326-1, EN 61326-2-1. EMC requirements for electrical equipment for
measurement, control, and laboratory use.
CISPR 11. Radiated and conducted emissions, Group 1, Class A 1,2,3
IEC 61000-4-2. Electrostatic discharge immunity
IEC 61000-4-3. RF electromagnetic field immunity 4
IEC 61000-4-4. Electrical fast transient/burst immunity
IEC 61000-4-5. Power line surge immunity
IEC 61000-4-6. Conducted RF immunity 5
IEC 61000-4-11. Voltage dips and interruptions immunity
EN 61000-3-2. AC power line harmonic emissions
EN 61000-3-3. Voltage changes, fluctuations, and flicker
European contact.
Tektronix UK, Ltd.
Western Peninsula
Western Road
Bracknell, RG12 1RF
United Kingdom
1This product is intended for use in nonresidential areas only. Use in residential areas may cause electromagnetic
interference.
2Emissions which exceed the levels required by this standard may occur when this equipment is connected to a
test object.
3To ensure compliance with the EMC standards listed here, high quality shielded interface cables should be used.
4Trace bloom not exceeding +/- 3 divisions pk-to-pk may be induced under the conditions of the IEC 61000-4-3
test.
5Trace bloom not exceeding +/-1 division pk-to-pk may be induced under the conditions of the IEC 61000-4-6 test.
THS3000 Series Oscilloscopes Installation and Safety Instructions 9

Compliance Information
Australia / New Zealand
Declaration of
Conformity – EMC
Complies with the EMC provision of the Radiocommunications Act per the
following standard, in accordance with ACMA:
CISPR 11. Radiated and Conducted Emissions, Group 1, Class A, in
accordance with EN 61326-1 and EN 61326-2-1.
10 THS3000 Series Oscilloscopes Installation and Safety Instructions

Compliance Information
Safety Compliance
EC Declaration of
Conformity – Low Voltage
Compliance was demonstrated to the following specification as listed in the
Official Journal of the European Communities:
Low Voltage Directive 2006/95/EC.
EN 61010-1: 2001. Safety requirements for electrical equipment for
measurement control and laboratory use.
EN 61010-031: 2008. Particular requirements for handheld probe assemblies
for electrical measurement and test equipment (including amendment 1).
U.S. Nationally Recognized
Testing Laboratory Listing
UL 61010-1:2004, 2nd Edition. Standard for electrical measuring and test
equipment.
UL 61010-031:2010, 1st Edition. Particular requirements for handheld
probe assemblies for electrical measurement and test equipment (including
amendment 1).
Canadian Certification CAN/CSA-C22.2 No. 61010-1:2004. Safety requirements for electrical
equipment for measurement, control, and laboratory use. Part 1.
CAN/CSA-C22.2 No. 61010-031-10, 1st Edition. Particular requirements for
handheld probe assemblies for electrical measurement and test equipment
(including amendment 1).
Additional Compliances IEC 61010-1: 2001. Safety requirements for electrical equipment for
measurement, control, and laboratory use.
IEC 61010-031: 2008. Particular requirements for handheld probe assemblies
for electrical measurement and test equipment (including amendment 1).
Equipment Type Test and measurement equipment.
Pollution Degree
Description
A measure of the contaminants that could occur in the environment around
and within a product. Typically the internal environment inside a product is
considered to be the same as the external. Products should be used only in the
environment for which they are rated.
Pollution Degree 1. No pollution or only dry, nonconductive pollution occurs.
Products in this category are generally encapsulated, hermetically sealed, or
located in clean rooms.
Pollution Degree 2. Normally only dry, nonconductive pollution occurs.
Occasionally a temporary conductivity that is caused by condensation must
THS3000 Series Oscilloscopes Installation and Safety Instructions 11

Compliance Information
be expected. This location is a typical office/home environment. Temporary
condensation occurs only when the product is out of service.
Pollution Degree 3. Conductive pollution, or dry, nonconductive pollution
that becomes conductive due to condensation. These are sheltered locations
where neither temperature nor humidity is controlled. The area is protected
from direct sunshine, rain, or direct wind.
Pollution Degree 4. Pollution that generates persistent conductivity through
conductive dust, rain, or snow. Typical outdoor locations.
Pollution Degree Pollution Degree 2 (as defined in IEC 61010-1).
Installation (Overvoltage)
Category Descriptions
Terminals on this product may have different installation (overvoltage) category
designations. The installation categories are:
Measurement Category IV. For measurements performed at the source of
low-voltage installation.
Measurement Category III. For measurements performed in the building
installation.
Measurement Category II. For measurements performed on circuits directly
connected to the low-voltage installation.
Measurement Category I. For measurements performed on circuits not
directly connected to MAINS.
Overvoltage Category Overvoltage Category II (as defined in IEC 61010-1)
12 THS3000 Series Oscilloscopes Installation and Safety Instructions

Compliance Information
Environmental Considerations
This section provides information about the environmental impact of the product.
Product End-of-Life
Handling
Observe the following guidelines when recycling an instrument or component:
Equipment Recycling.
Production of this equipment required the extraction and use of natural resources.
The equipment may contain substances that could be harmful to the environment
or human health if improperly handled at the product’s end of life. In order to avoid
release of such substances into the environment and to reduce the use of natural
resources, we encourage you to recycle this product in an appropriate system that
will ensure that most of the materials are reused or recycled appropriately.
This symbol indicates that this product complies with the applicable European
Union requirements according to Directives 2002/96/EC and 2006/66/EC
on waste electrical and electronic equipment (WEEE) and batteries. For
information about recycling options, check the Support/Service section of the
Tektronix Web site (www.tek.com).
Battery Recycling. The included THSBAT lithium-ion rechargeable battery pack
must be recycled or disposed of properly.
Lithium-Ion batteries are subject to disposal and recycling regulations that
vary by country and region. Always check and follow your applicable
regulations before disposing of any battery. Contact Rechargeable Battery
Recycling Corporation (www.rbrc.org) for U.S.A. and Canada, or your local
battery recycling organization.
Many countries prohibit the disposal of waste electronic equipment in
standard waste receptacles.
Place only discharged batteries in a battery collection container. Use electrical
tape or other approved covering over the battery connection points to prevent
short circuits.
Transporting Lithium-Ion
Batteries
The capacity of the lithium-ion rechargeable battery pack in this product is
under 100 Wh. The lithium equivalent content has been shown to meet the
applicable requirements as defined by the UN Manual of Tests and Criteria Part
III Subsection 38.3.
Always check all applicable local, national, and international regulations
before transporting a lithium-ion battery.
Transporting an end-of-life, damaged, or recalled battery may, in certain
cases, be specifically limited or prohibited.
THS3000 Series Oscilloscopes Installation and Safety Instructions 13

Compliance Information
Restriction of Hazardous
Substances
This product is classified as Monitoring and Control equipment, and is outside the
scope of the 2002/95/EC RoHS Directive.
14 THS3000 Series Oscilloscopes Installation and Safety Instructions