Tenda G1005D User manual

Copyright Statement
is the registered trademark of Shenzhen
Tenda Technology Co., Ltd. All the products and product names
mentioned herein are the trademarks or registered trademarks
of their respective holders. Copyright of the whole product as
integration, including its accessories and software, belongs to
Shenzhen Tenda Technology Co., Ltd. Without the permission of
Shenzhen Tenda Technology Co., Ltd, any individual or party is
not allowed to copy, plagiarize, imitate or translate it into other
languages.
All the photos and product specifications mentioned in this guide
are for references only. As the upgrade of software and
hardware, there will be changes. And if there are changes,
Tenda is not responsible for informing in advance. If you want to
know more about our product information, please visit our
website at www.tenda.cn.

Content
1. Introduction ------------------------------------------------1
1.1 Switch Features --------------------------------------------1
1.2 Package Contents -----------------------------------------2
1.3 Front Panel and Side Panel Specifications --------------2
1.4 LED Indicator Specifications------------------------------3
2. Installation -------------------------------------------------5
2.1 Before Connecting to the Network ----------------------5
2.2 Connecting to End Nodes--------------------------------5
2.3 Switch to Router or Switch --------------------------------6
3. Product Specification --------------------------------------7

1
1. Introduction
The G1005D/G1008D 5/8-Port Desktop Gigabit Ethernet Switch,
mini and exquisite, is especially suitable for small-sized
networking. It provides 5/8 10/100/1000Mbps Auto-negotiation
ports and supports Auto MDI/MDIX. These Gigabit ports can be
used not only as ordinary ports, but as Uplink ports connected to
other networking devices. You can replace the 10/100Mbps
switch with the G1005D/G1008D to resolve the bottleneck
issues of server terminal connectivity, because the speed at each
port can be up to 2000Mbps in full-duplex mode. It’s the best
choice for you to upgrade from the normal 10/100Mbps to
1000Mbps. Moreover, its easy setup and no network
management will benefit you a lot. So you can select this Gigabit
Switch as a prime switch to improve the speed between different
departments and servers.
1.1 Switch Features
Complies with IEEE802.3, IEEE802.3u and
IEEE802.3ab Ethernet standards
Supports Auto MDI/MDIX on each port
Supports NWAY Auto-Negotiation function
Provides 5/8 10/100/1000Mbps Auto-Negotiation
RJ-45 ports

2
Supports IEEE802.3x flow control for full-duplex and
Backpressure flow control for half-duplex
Provides up to 10/16Gbps backplane bandwidth and
non-blocking line speed forwarding
Supports store-and-forward switching method
Provides MAC address self-learning/auto-aging and
8K MAC address entries
Desktop and mini plastic shell design
1.2 Package Contents
Please check the articles carefully after you open the packing as
below:
One 5/8-Port Desktop Gigabit Ethernet Switch
One Power Adapter
One User Guide
One Warranty Card
If any of the listed items are missing or damaged, please contact
the reseller from whom you purchased for replacement.
1.3 Front Panel and Rear Panel Specifications
The front panel of 5/8-Port Desktop Gigabit Ethernet Switch
includes 5/8 Link/Act indicators and one power indicator. Please

3
refer to the detailed description of these indicators in LED
Indicator Specifications.
The front panel of the Switch
The Rear Panel of the Switch includes 5/8 10/100/1000Mbps
RJ-45 ports and one AC power port used for AC power input.
The rear panel of the Switch
Notice: Please use the delivery-attached power adapter. If
not, the switch may be damaged.
1.4 LED Indicator Specifications
The LED indicators of the Switch include Power and 5/8 Link/Act
indicators. You can see their operating situation through these
LED indicators.
The following chart shows the LED indicators of the Switch along
with explanation of each indicator.

4
LED Color Status Description
Green ON
This indicator lights
when the Switch turns
on.
Power
— OFF
If this indicator is not
lighting, please check
the AC power connector
to ensure proper
connectivity of the
power cable and the
Switch.
ON
Indicates the Switch is
connected on
1000Mbps.
Green
Blinking
Indicates the Switch is
transmitting/receiving
data packets at
1000Mbps.
ON
Indicates the Switch is
connected on
10/100Mbps.
Red
Blinking
Indicates the Switch is
transmitting/receiving
data packets at
10/100Mbps.
Link/Act
—OFF Indicates the connection
fails.

5
2. Installation
2.1 Before Connecting to the Network
Before connecting the G1005D/G1008D to the network, please
pay attention to the following instructions:
¾Don’t put heavy articles on the Switch.
¾Power sockets and equipments should be within 1.5 meters
of the Switch.
¾Check power adapter to confirm the safe connection.
¾Make sure there’s adequate space for proper heat
dissipation and adequate ventilation around the Switch.
2.2 Connecting to End Nodes
Use standard Ethernet cable to connect the Switch to end nodes
as described below. Switch ports will automatically adjust to the
characteristics (MDI/MDIX, speed, duplex) of the device to which
is connected.
Switch connecting to an end node

6
Please refer to the LED Indicator Specifications. The Link/Act
LEDs for each port are turned on when the link is available.
2.3 Switch to Router or Switch
Connecting to another router or switch
Please refer to the LED Indicator Specifications. The Link/Act
LEDs for each port are turned on when the link is available.

7
3. Product Specification
Standards
IEEE802.3 10Base-T Ethernet
IEEE802.3u 100 Base-TX Fast
Ethernet
IEEE802.3ab Gigabit Ethernet
Protocol CSMA/CD
Topol o gy Sta r
Network Cables
10 Base-T: Cat.3 UTP or above
100 Base-TX: Cat.5 UTP /STP
1000Base-T: Cat.5, Cat.5e or
Cat.6 UTP/STP
Speed 10/100/1000Mbps
Transmission Method store-and-forward
MAC Address Table 8K entries
14880pps(10Mbps)per port
148800pps(100Mbps)
per port
Packet Filtering/
Forwarding Rate 1488000pps(1000Mbps)
per port
MAC Address Learning
Self-learning, auto-aging
Power External universal power supply
AC Input AC 9V 1200mA
Power Consumption 6W/7.2W
Operating Temperature
0OC ~40OC
Storage Temperature -40OC ~70OC
Operating Humidity 10%~90% RH no condensing
Storage Humidity 5%~90% RH no condensing