Tenda TEI402M User manual

Copyright Statement
is the registered trademark of Shenzhen Tenda
Technology Co., Ltd. Other trademark or trade name mentioned
herein are the trademark or registered trademark of the
company. Copyright of the whole product as integration,
including its accessories and software, belongs to Shenzhen
Tenda Technology Co., Ltd. Without the permission of Shenzhen
Tenda Technology Co., Ltd, individual or party is not allowed to
copy, plagiarize, imitate or translate it into other languages.
All the photos and product specifications mentioned in this
manual are for references only, as the upgrading of software and
hardware, there will be changes. And if there are changes,
Tenda is not responsible for informing in advance. If you want to
know more about our products information, please visit our
website at www.tenda.cn

TEI402M Multifunction Broad Band Router
1
Table of Contents
Chapter 1 Introduction............................................................ 3
1.1 Product Feature ................................................................ 3
1.2 Package Contents ............................................................. 3
Chapter 2 Hardware Setup ..................................................... 4
2.1 Rear Panel ......................................................................... 4
2.2 Front Panel ........................................................................ 4
2.3 Hardware Install Process ................................................. 5
Chapter 3 Router Setting........................................................ 6
3.1 Setup Right Network......................................................... 6
3.2 Fast Setup Guide .............................................................. 6
3.3 Config Illuminate..............................................................11
3.3.1 Running Status..............................................................11
3.3.2 Wizard ............................................................................11
Please refer to 3.2 Fast Setup Guide....................................11
3.3.3 Advanced Config...........................................................11
3.3.3.1 LAN Port .....................................................................11

TEI402M Multifunction Broad Band Router
2
3.3.3.2 WAN Port Setup ........................................................ 12
3.3.3.3 MAC Address Clone.................................................. 12
3.3.3.4 DNS ............................................................................ 13
3.3.4 DHCP Server................................................................. 13
3.3.4.1 DHCP Service ............................................................ 13
3.3.4.2 DHCP Client List........................................................ 14
3.3.5 Virtual Service .............................................................. 14
3.3.5.1 Virtual Server............................................................. 14
3.3.5.2 DMZ Host ................................................................... 15
3.3.5.3 UPnP Mapping Table................................................. 15
3.3.6 Secruity Setting............................................................ 15
3.3.6.1 Firewall Setting ......................................................... 15
3.3.6.2 URL Filter................................................................... 15
3.3.6.3 MAC Filter .................................................................. 15
3.3.6.4 Remote WEB Management....................................... 15
3.3.6.5 WAN Port Ping........................................................... 16
3.3.6.6 Special Application Filter ......................................... 16
Appendices : Default setting of the router.......................... 17

TEI402M Multifunction Broad Band Router
3
Chapter 1 Introduction
1.1 Product Feature
 One 10M/100M auto negotiation WAN port, connectible to
xDSL/Cable Modem or Ethernet
 Four 10M/100M auto negotiation LAN ports
 Compliant with IEEE802.3 Ethernet Standard and
IEEE802.3u Fast Ethernet Standard
 Support TCP/IP, PPPoE, PPTP, DHCP, ICMP, NAT, SNTP
protocol
 Prevent D.O.S Network attack
 Support VPN Pass through
 Support UPnP, support MSN audio and video
Communication
Support DDNS
 Provide DHCP server, support fixed IP address
 Support static and dynamic Routing
 Support Virtual server, support DMZ host
 Support MAC address filter, can control user access
Internet
 Support URL filter, can control user access Web site
 Run or Stop at set time, save Internet access money
 Local、Remote Web management, English Web pages
 Upgrade firmware on the Web
1.2 Package Contents
 Multifunctional Broadband Router
 Power Adapter
 User Manual

TEI402M Multifunction Broad Band Router
Chapter 2 Hardware Setup
2.1 Rear Panel
Power: Special Power Adapter.
WAN: WAN PORT(RJ-45) Connect to Xdsl/Cable Modem or
Ethernet.
LAN Port: 4 RJ-45 ports Computer and HUB/Switch connect
Ethernet through these ports.
Notice:
1. please use the special power with this router otherwise it will
be damaged.
2. WAN: WAN port(RJ-45) To connect the router with XDSL or
Enthernet
3. LAN: 4 RJ-45 Port.
4. Reset: Press this button for 3 seconds, the LED indicators of
SYS will fast blink. Loosen the botton the router will restore
default setting and restart automatically.
2.2 Front Panel
LED Indicators
Link/Act Status
Indication for
WAN & LAN
LED will LIGHT when link is
established LED will blink when
packet is transmitting or receiving
POWER Power
Indication
LED will LIGHT when powered on
SYS System
Indication
LED will blink when system work.
LED will dark when system restart
or loading system
4

TEI402M Multifunction Broad Band Router
5
2.3 Hardware Install Process
2.3.1.Establish LAN Connection
Connect the port of router with HUB or switch by a line. You also
can connect the computer LAN card directly.
2.3.2 Establish WAN Connection
Connect the WAN port of router with xDSL/Cable Modem by a
line.
2.3.3.Power Link
Link the power and the router will start automatically.

TEI402M Multifunction Broad Band Router
6
Chapter 3 Router Setting
3.1 Setup Right Network
The default IP address of this router is 192.168.0.1.The default
subnet mask is255.255.255.0.All these parameters can be
amended if needed but in this use manual we will illuminate
according the fault parameters.
First please connect your computer with the LAN port of the
router and then set the IP address of your computer.
Hint: The LED indicators of the Link/Act of the router and the
LAN card of your computer must light at the same time .
Hint:If the IP address of your router is 192.168.8.1,then the IP
address of your computer must be 192.168.0.xxx(from 2 to 254).
3.2 Fast Setup Guide
Click Internet Explore or Netscape Communicator and enter the
IP address of this router (default setting:192.168.0.1),a user
name and password screen will appear.
Hint: If you use agent server please cancel this option or add the
IP address of the router to the Exception of the agent server
setup(you can find these setup in the TOOL of IE).

TEI402M Multifunction Broad Band Router
If the user name and password is correct, a screen of
administrator pattern will appear .The default user name and
password are all admin.
Click “Next” or Wizard of left manual to select how to access
internet.(This router can access internet in 3 ways).
1. If you select PPPoE(ADSL Virtual Dial- up), you need to
enter the following:
7

TEI402M Multifunction Broad Band Router
Username & Password: Enter Account and password provided
by ISP. If you don’t know them please refer to ISP.
2. If you can access internet with dynamic IP address .Namely,
you can obtain IP address automatically from your ISP .You
needn’t write any parameter and access internet
automatically .（If your ISP need to integrate the MAC address
of your Lan card you can clone MAC address）.
3. If you can access internet with fixed. Namely, you have the
fixed IP address provide by your ISP address, you need fill in
the following data:
IP address: The router IP address to WAN. If you don’t know
them well please refer to your ISP .
8

TEI402M Multifunction Broad Band Router
Subnet Mask: The router subnet mask to WAN (default
setting:255.255.255.0).
Gateway: Fill in the gateway provide by your ISP, If you don’t
know them well please refer to your ISP .
Primary DNS: Fill in the DNS server provide by your ISP, If you
don’t know them well please refer to your ISP.
Secondary DNS: Optional. If your ISP provide you with two DNS,
you can fill in the other here.
4. If you can access internet with PPTP, you need to enter the
following: (The parameters are just for your reference. If you
do not know any of the details, or your provider uses PPPoE
or PPTP, please contact your provider for more information.
Username and password are usually supplied by your
provider in your first-time setup documents.)
PPTP Account: Your adsl or cable login name
(example☺‘user@adsl-comfort’ of ‘user@xs4all-basic-adsl’
PPTP Password: Your adsl or cable password
PPTP Gateway: IP address
9

TEI402M Multifunction Broad Band Router
IP address: 10.0.0.138
Connection ID: (Connection name. Can be left empty)
MTU: 1400
MPPE: un-check ‘enabled’ checkbox.
WAN Interface IP: Static IP
IP address: 10.0.0.150
Subnet mask: 255.255.255.0
Gateway: 10.0.0.138 (your modem’s ip)
After filling in all the above parameters please come to
Configuration Wizard as follows:
Now, please click Save to save fast setting.
If you need setup firewall, MAC address Filter, ULR Filter, please
click Security Setting.
10
If you want to setup WAN port parameter, LAN port Parameter

TEI402M Multifunction Broad Band Router
11
and clone MAC address, please click Advanced Config.
If you need setup DHCP service, please click DHCP Server .
If you need startup DMZ, UpnP and Virtual Service, please click
Virtual Service.
If you need setup dynamic DNS, modify User information, restart
router, upgrade software, backup currently setting, please click
System Tool.
3.3 Config Illuminate
3.3.1 Running Status
1. WAN
Shows the way to access internet and connection status
currently
2. LAN
Shows the current status of IP address, DHCP service, NAT
and firewall of this router.
3. Information
Shows the current running time, number of client and
system version.
3.3.2 Wizard
Please refer to 3.2 Fast Setup Guide.
3.3.3 Advanced Config
3.3.3.1 LAN Port
This page sets the basic network parameters
IP address：the router IP address to LAN. The factory fault
setting is 192.168.0.1.You can change it according to your

TEI402M Multifunction Broad Band Router
requirements.
Notice: If you change the IP address, you must use the
new IP address to log on the router to manage the WEB
interface and all default gateway of computers of the LAN must
setup as the new IP address.
Subnet Mask: the default setting is 255.255.255.0.
Notice: All subnet mask of computers in the LAN must be
same as the above setting.
3.3.3.2 WAN Port Setup
First please select the way you want to access internet, the fault
way is Dynamic IP .
1. If you access internet by Dynamic IP, you can obtain IP
address automatically from ISP. If your ISP need integrate
the Mac address of your LAN card, you can clone the MAC
address during setting.
2. If you access internet by Static IP and you have fixed IP
address provided by ISP, you will see the following screen
and you need setting the parameters in the menu.
3. If you access internet by PPPoE, you will see the following
screen and you need setting the following parameters:
3.3.3.3 MAC Address Clone
You can select the option to clone the MAC address of the
12

TEI402M Multifunction Broad Band Router
management computer to that of Wan port(you also can modify
it by manual).
3.3.3.4 DNS
Primary DNS: Fill in the DNS server provide by your ISP, If you
don’t know them well please refer to your ISP.
Secondary DNS: Optional. If your ISP provide you with two
DNS, you can fill in the other here.
Notice: The function of DNS is to transform the domain
name (we input) into IP address.
3.3.4 DHCP Server
3.3.4.1 DHCP Service
To use DHCP server utility, you need set the following
parameters:
Start the DHCP Server
The first address of IP address pool: The beginning address
automatically assigned by DHCP server.
The end address of IP address pool: The close address
automatically assigned by DHCP server.
Notice: to use the function of DHCP Server, the TCP/IP of
must be setup as automatically obtain IP address.
13

TEI402M Multifunction Broad Band Router
3.3.4.2 DHCP Client List
DHCP Client List show the assigned IP address, client MAC
address and HOST name.
3.3.5 Virtual Service
In the Virtual Service menu, there are five submenu:
Virtual server , DMZ Host, UpnP setting, and UpnP mapping
Table. Click one and you can check and config it.
3.3.5.1 Virtual Server
With default settings, computers of WAN have no access to
some servers of the LAN via this router with firewall integrated.
To solve this problem, i.e. to protect the LAN from external
attack and facilitate valid access from WAN, the router provides
virtual server function by defining a server port and all the
access claim to that port is then reallocated to the server in LAN
through IP address.
To use the virtual service function, you need to setup the
parameters in the menu.
Notice: If you setup the virtual server with service port:80
you need set the option Remote WEB Management of Security
Setting as other parameter otherwise collision will happen and
the virtual service could work. You need to restart the router to
take the function effect.
14

TEI402M Multifunction Broad Band Router
15
3.3.5.2 DMZ Host
In some special situation, a computer need to exposure entirely
to WAN in order to implement intercommunication. You need
appoint the computer as DMZ host.
3.3.5.3 UPnP Mapping Table
This page shows the status of UPnP equipments.
3.3.6 Secruity Setting
3.3.6.1 Firewall Setting
You can control the access between computer of LAN and
computer on internet by client filter function.
3.3.6.2 URL Filter
You can control the access of computers in the LAN by URL filter
function, which can designate what client can not access what
web sites.
3.3.6.3 MAC Filter
You can control the access of the computers in the LAN to the
internet by MAC filter function.
3.3.6.4 Remote WEB Management
This pages is to set the web management port of the router and
the IP address of the computer that perform remote web
manages.

TEI402M Multifunction Broad Band Router
Port: The executive web management port number.
IP Address: The IP address of the computer in WAN that remote
web manages.
Notes:
1. The default web management port of the router is 80, if the
web management port is changed (e.g..8080), the user
should input "IP : port number" (e.g.:http://192.168.0.1:8080)
to log on the router and enter the web management
interface.
2. The default IP address of computer that perform remote
web manages is 0.0.0.0. With default setting there's no
access for computers in WAN to log on the router and
execute the remote web management. If you change the
default setting, there is only access for computer in WAN to
log on the router and execute the remote web management
when the IP address of the computer (e.g..218.88.93.33) is
the same as the modified web management IP address of
the router (e.g.. 218.88.93.33).
3.3.6.5 WAN Port Ping
You can forbid the Ping from Wan by this function.
3.3.6.6 Special Application Filter
You can forbid MSN &QQ by this function.
3.3.7 Routing
3.3.7.1 Routing Table
3.3.7.2 Static Routing Table
This page set the static routing function of router and you can
designate static routing rule.
Notice:
1. The gateway IP and the Wan or LAN port must belong to the
16

TEI402M Multifunction Broad Band Router
17
same network segment.
2. If the target IP address is a IP address of host, the subnet
mask must be 255.255.255.255.
3. The target IP address must match the subnet mask if it is in
IP network segment. For example, if the target IP is
10.0.0.0,the subnet mask should be 255.0.0.0 and if the
target is 10.1.2.0,subnt mask should be 255.255.255.0
Appendices : Default setting of the router
Parameter Setting Notes
User Name admin You’d better modify it
Password admin You’d better modify it
LAN Port IP
address 192.168.0.1 You’d better use
address of C type
LAN Port Subnet
Mask 255.255.255.0 You’d better use
address of C type
Running Status Dynamic IP
DHCP Server on
Firewall off
URL Filter off
MAC Address
Filter off
WEB Server Port 80
Remote WEB IP 0.0.0.0 Forbid remote WEB
management
Ignore WAN Ping off
Remote computer in
WAN cann’t PING
router
Timing Server IP 18.145.0.30 Tick.mit.edu