Tenda TEG1016G User manual

Copyright Statement
is the registered trademark of Shenzhen Tenda
Technology Co., Ltd. All the products and product names mentioned
herein are the trademarks or registered trademarks of their respective
holders. Copyright of the whole product as integration, including its
accessories and software, belongs to Shenzhen Tenda Technology Co.,
Ltd. ithout the permission of Shenzhen Tenda Technology Co., Ltd,
any individual or party is not allowed to copy, plagiarize, imitate or
translate it into other languages.
All the photos and product specifications mentioned in this guide are for
references only. As the upgrade of software and hardware, there will be
changes. And if there are changes, Tenda is not responsible for
informing in advance. If you want to know more about our product
information, please visit our website at www.tenda.cn.

1. Introduction
TEG1016G/1024G is a rack-mountable Gigabit Ethernet Switch, which
is specially designed to resolve data transfer bottleneck for enterprises
and Internet Cafés. It has 16/24 10/100/1000Mbps RJ-45 Auto-
negotiation Ethernet ports, supports auto MDI/MDI-X function. In
addition, the Gigabit ports can be used as normal ports to connect
Gigabit terminals such as PC, as well as Uplink ports to connect
backbone network. You can replace the 10/100Mbps switch with the
TEG1016G/TEG1024G to resolve the bottleneck issues of server and
terminal connectivity. Meanwhile, it can be used as main switch to
connect the Gigabit LAN of enterprises or Internet Cafés, and greatly
improves the transmission rate between different departments, or
terminal and server. In a word, it is a cost-effective Gigabit Ethernet
Switch with high performance.
1.1 Switch Features
Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab, IEEE
802.3x standards.
2

Supports IEEE802.3x flow control for full-duplex, and
backpressure flow control for half-duplex.
Provides 16/24 Gigabit self-adaptive RJ-45 ports, supports 802.3
N ay Auto-negotiation.
Each RJ-45 port supports Auto-MDI/MDIX function.
Supports MAC address auto-learning and aging function.
Adopts store- and- forward switching method.
Supports up to 32Gbps/48Gbps backplane bandwidth.
Transmission rate of each port reaches up to 1488095pps.
Supports 8K MAC address table
Equipped with high performance power supply.
1.2 Package Contents
Please check the items carefully after you open the packing as below:
(The listed items are for reference only)
One Gigabit Ethernet Switch
One power cord
One User Guide
One Set of L-shaped Bracket （two mounting ears, matched
screws ）
Four foot pads
3

1.3 Front Panel and Rear Panel Specifications
On the front panel, there are 16/24 1000Mbps RJ45 ports and LED
indicators as well as 1 power indicator.
Front panel iew of the TEG1024G Switch
On the rear panel there are 1 AC power port and the matched power
supply mark.
Rear panel iew of the Switch
1.4 LED Indicator Specifications
The LED indicators of the Switch include Power, Link/ACT and
1000Mbps indicators. You can see their operating situation through
these green LED indicators.
4

LED indicators of the TEG1024G Switch
Please refer to the list below for the LED indicator definition.
LED Indicator Status Description
PO ER
Always ON Indicates the Switch is powerd on
OFF Indicates the Switch is powerd off
1000Mbps ON The Switch connects to the other
devices at 1000Mbps speed.
OFF Indicates there’s no connection or the
speed is at 10Mbps or 100Mbps
LINK/ACT
Flashing Indicates the switch is transmitting
data
Always ON Indicates no data is being
transmitting
2. Installation
2.1 Installation instructions
Before connecting to the network, please pay attention to the following
5

instructions:
Put the switch in clean place where there is adequate ventilation
Place the switch on stable desk in case of falling.
Make sure there’s at least 10cm’s space for dissipation.
Don’t put heavy articles on the Switch.
hen the devices need to be used by overlapping, make sure the
vertical distance is over 1.5cm.
The power supply used should match the required power
specification of the switch.
2.2 Installation methods
TEG1016G/TEG1024G switch can be installed to desktop or standard
19-inch rack
1. Install the switch to the desktop.
Install the 4 included foot pads to the corresponding position at the
bottom of the switch and then place it on the desktop.
6

Install the foot pads to the bottom of the Switch
2. Install the Switch to the standard 19-inch rack.
Please follow the steps below:
Make sure the rack is stable.
Fix the 2 delivery-attached mounting ears on both sides of the
Switch with the matched screws.
Install the L-shaped brackets to the Switch
Mount the Switch into one layer of the rack, and then use screws
provided to mount the Switch in the rack.
Install the Switch to standard 19-inch rack
7

2.3 Application example
ith 16/24 RJ-45 ports, TEG1016G/TEG1024G switch can be
connected to devices such as PCs and notebook computers.
The common method to access the internet
8

3. Product Specification
Features
Standard IEEE802.3 IEEE802.3u
IEEE802.3ab IEEE802.3x
Protocol CSMA/CD Ethernet
Data Transmission
Rate
Gigabit Ethernet: 2000Mbps (Full-duplex)
Fast Ethernet: 100Mbps (Half-duplex)
200Mbps (Full-duplex)
Topological Structure Star
Network Cables 10Base-T:Cat.3 UTP or above(100m)
100Base-TX: Cat.5 UTP /STP(100m)
1000Base-T: Cat.5e UTP/STP or
above(100m)
Port Quantity 16/24 10/100/1000Mbps RJ-45 ports
Performance
Transmission Method store-and-forward
MAC Address Table 8K
Packet Filtering/
Forwarding Rate
14880pps (10Mbps) per port
148800pps (100Mbps) per port
1488095pps (1000Mbps) per port
MAC Address Learning Auto-learning, auto-aging.
Backplane Bandwidth 32Gbps/48Gbps
Physical and En ironmental
AC Input Range 100-240V~ 0.6A(Max) 50/60Hz
Power Consumption 25 /30
9

Operating Temperature 0℃-40℃
Storage Temperature -40℃-70℃
Storage Humidity 10%～90%RH (non- condensing)
Operating Humidity 5%～90%RH (non- condensing)
Dissipation method fan
FCC Statement
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
10

—Consult the dealer or an experienced radio/TV technician for help.
If you still have some problems, please contact our customer
service
Technical Support
Toll Free: 400-6622-666 (For Mainland hina Only)
Toll Free: 1-800-570-5892 (For USA only)
Tel: [phone]
Skype: tendasz
MSN: [email protected]
Email: [email protected]
Headquarter Shenzhen:
Add: Tenda Industrial Zone,No.34-1 Shilong Road, ShiyanTown,
Baoan District, Shenzhen, hina. 518108
Tel:[phone]
Fax: [phone]
Email: [email protected]
Technical Support: [email protected]
Tekninen tuki: [email protected]
11