Tern DuoStand Gen 2 User manual

1
ternbicycles.com
DuoStand™
Safety
If you are unsure how to install this product, please visit your local dealer.
Do not exceed the load limit of 60 kg (132 lb). Please remember the max load limit includes the weight of the bike.
Never leave children or pets on a parked bike unattended.
What’s Included
• DuoStand
• M10 x 30 Bolt x 2
• M10 x 70 Bolt x 1**
• M10 Nut x 2
• M10 Washer x 4
• M10 Spring Washer x 1**
• Flat Plate
Installation
Tools required (not included)
• 17 mm Wrench x 2
• 3, 4, or 5 mm Allen Wrench
Additional Kit Required (For HSD Gen 1
Owners Only)
The DuoStand HSD Kit (sold separately) is required to install
the DuoStand on bikes with the HSD Gen 1 frame. Please see the
illustrations on the next page to determine which HSD frame you
have.
1. Remove the existing kickstand. (Tool may differ depending on your bike.)
* DuoStand HSD Kit
– M10 x 45 Bolt x 2
– Bushing x 2
– Wing-shaped Plate
For HSD Gen 1 Owners
Identify the HSD Frame
Before installation, identify the HSD Gen 1 frame by the kickstand mount located in front of the rear wheel.
2. Install Bolt Sets in the order and arrangement shown below.
HSD Gen 1 only Mounting Location for HSD Gen 1 and Gen 1A
HSD Gen 1 Assembly Order
1. Nut
2. Washer
3. Wing-shaped plate*
4. Bushing*
5. Bike frame
6. Flat plate
7. DuoStand
8. Washer
9. Bolt*
* Use parts from
the DuoStand
HSD Kit.
HSD Gen 1A Assembly Order
1. Nut
2. Washer
3. Bike frame
4. Flat plate
5. DuoStand
6. Washer
7. M10 x 30 Bolt
WARNING: Route cables as shown to
avoid damage from compression.
HSD Gen 1 frame variants
HSD Gen 1
HSD Gen 1A
HSD Gen 1
HSD Gen 1A
DuoStand Ends
17 mm
17 mm
35 Nm – 40 Nm
17 mm
17 mm
35 Nm – 40 Nm
Add anti-seize lubricant to the tip of the bolts before securing the
nuts. If anti-seize lubricant is not available, apply any standard
lubricant to reduce friction and prevent thread galling.
**Note: The M10 x 70 Bolt and M10 Spring Washer
are not required to install the DuoStand.
Make sure you have the latest support resources!
Visit ternbicycles.com/support for:
Manual Version 04
DuoStand Gen 2

2
ternbicycles.com
DuoStand™
LIMITED PRODUCT WARRANTY INFORMATION: This Product comes with a ONE (1) YEAR Limited Warranty from the date of retail purchase by the
original end-user. If a material or workmanship defect arises and a valid claim is received within the Warranty Period, this Product will be replaced.
Mobility Holdings cannot be held liable for damages to personal property due to misuse or improper care and maintenance. This Product Warranty
does not, under any circumstance, cover the replacement or cost of any third party product used with or connected to the Product.
Tern, the Tern Werd (logotype), the Tern Berd (device), Lockstand, HSD, Quick Haul, Short Haul, and DuoStand used alone or in combination are trade
names, trade devices or registered trademarks of Mobility Holdings, Ltd.
© 2023. Tern is a trademark of Mobility Holdings, Ltd. All Rights Reserved.
ternbicycles.com
@ternbicycles
3. The recommended clearance from the bottom of the rear wheel to the ground is 10 - 20 mm (2/5” - 4/5”). Measure the distance from the bottom of
the rear tire to the ground and adjust the height of the DuoStand by loosening the bolts on the DuoStand Ends to raise or lower the legs. Tighten
the bolts to a torque of 8 - 9 Nm.
Optional: Install Lockstand™Extensions
For maximum stability when parked, install the Lockstand Extensions. Available for purchase from your local Tern dealer.
10 - 20 mm
For HSD Gen 2, Quick Haul, & Short Haul Owners
Mounting LocationAssembly Order
1. Nut
2. Washer
3. Bike frame
4. DuoStand
5. Washer
6. M10 x 30 Bolt
17 mm
17 mm
35 Nm – 40 Nm
2. Install the Bolt Sets in the order and arrangement shown below.
DuoStand Gen 2