TerraTrike SPYDER Manual

www.TerraTrike.com | 616.608.8086
Revised 10/2021
Build Notes
&

www.TerraTrike.com | 616.608.8086
Frame Assembly
Install rear frame section and derailleur hanger as shown below.
Torque specs:Top bolt(2) 8.5Nm, Bottom Bolt(4) 20Nm.
1 15x23mm Cap WH000048
2 15x74mm Bolt WH000049
3 28.6x28mm Cap WH000050
4 28.6x77mm Bolt WH000051
5 Derailleur Hanger with Bolt WC000040
1
2 3
4
5

www.TerraTrike.com | 616.608.8086
Alignment
29¼
Inate tires before performing alignment. The Spyder alignment measurement is
approximately 29¼ inches (center tread to center tread), though slight variance is
possible. Most importantly, make sure the alignment remains neutral with a rider
seated in the trike.
Left Right
Tie Rod Assembly
29¼

www.TerraTrike.com | 616.608.8086
Spyder Steering Stack Assembly
1M6x30 Socket Head Bolt TT000576
2Hybrid Top Cap TT000506
3Spyder Handlebar Pair TT600930
4Hybrid Headset Spacer TT000520
5 Hybrid Headset Cap TT000505
6Plastic Bushing TT000504
7 Hybrid Headset Bearing TT000600
8Hybrid Steering Crown Race TT000601
9 Rapid Axle Hubmount - RH TT000713
Rapid Axle Hubmount - LH TT000714
Rapid Axle Hubmount - Pair TT000516
10 Rapid Axle - RH TT000717
Rapid Axle - LH TT000718
Rapid Axle - Pair TT000563
11 Axle Spacer TT000568
9
8
7
1
6
3
6
5
4
2
10

www.TerraTrike.com | 616.608.8086
Steering Stack Assembly Continued* Install
11
Install Axle Spacer (11) between brake rotor and hub.

www.TerraTrike.com | 616.608.8086
Handlebar Assembly
Minimum insertion of the handlebars is 7cm from the alignment marking nearest the
handlebar upright.
Brake Lever Orientation: (Spyder model only)

www.TerraTrike.com | 616.608.8086
Chain Tube Setup/ Idler Setup
1
16t Aluminum Idler with cage WC000041
2M8x30 Bolt TT000280
3
14cm LDPE Chain Tube WC000039
4
Spyder Chain Tube Clamp WC000038
1
16t Aluminum Idler with cage WC000041
2M8x30 Bolt TT000280
1
2
3
1
2
4

www.TerraTrike.com | 616.608.8086
Cable Routing
Note: Internal cable routing kit is necessary to complete cable routing.
Remove Spyder Head Badge and housing ferrules prior to routing cables.
Chain Routing
Right Hand:
When routing RH cable housing, it is recommended to start installation at outrigger
cable guide. Feed housing from outrigger to the badge window, and then through
the mainframe. Next, route the housing from the mainframe through the rear frame
section to rear derailleur. Finish by routing housing from outrigger cable guide, to
handlebar cable guide and through handlebar. Install shifter and shift cable.
Shift Cable (solid=external routing, dashed=internal routing)
Brake Cable

www.TerraTrike.com | 616.608.8086
Left Hand:
When routing LH cable housing, it is recommended to start installation at boom
cable guide. Feed housing through boom/boom receiver tube to the badge window,
and then through outrigger. Finish by routing housing from outrigger cable guide to
handlebar cable guide and through handlebar. Install shifter and shift cable.
Brake Cable
Shift Cable (solid=external, dashed=internal)

www.TerraTrike.com | 616.608.8086
Inline Barrel Adjuster: (Spyder model only)
Install inline barrel adjuster on rear cable housing after the housing has been routed
through the frame. Install the 7” cable housing section between barrel adjuster and
rear derailleur.

www.TerraTrike.com | 616.608.8086
Lower: Install seat bolts (5) & (6) into lower mounting holes on seat. Install M5x45
bolt (7) and tighten to 5Nm.
ATC Carbon Seat Assembly
1
3
2
5 6 7
4
Upper: Install offset insert (4) into seat mount on mainframe. Install threaded cap (1)
and through hole cap (2) into upper mounting holes on seat. Install M5x65 bolt (3)
and tighten to 5Nm.
Perspective: Front of trike.

www.TerraTrike.com | 616.608.8086
Sport Touring Seat Assembly
1
2
3
4
5
Upper: Install offset insert (4) into seat mount on mainframe. Install M15 threaded
press t bushing (1) and M15 press t bushing (2) into upper seat mounting tabs.
Install M5x80 bolts (3) and tighten to 5Nm.
Lower: Install xed seat bolt (5) into lower seat mounting tabs and tighten.
Perspective: Front of trike.

www.TerraTrike.com | 616.608.8086
Flag Mount is included in parts kit box. Can be installed over the mesh on left or
right bottle cage bosses located on the side rails of the Sport Touring Seat.
1ATC Threaded Cap TT000879
2 ATC Through Hole Cap TT000880
3 M5x65mm Bolt WH000012
4 Offset Insert TT000870
5ATC Seat Bolt Threaded TT000881
6ATC Seat Bolt Through
Hole
TT000882
7 M5x45mm Bolt WH000013
Carbon Seat Assembly Sport Touring Seat Assembly
1M15 Threaded Press Fit
Bushing
TT000869
2M15 Press Fit Bushing TT000868
3 M5x80mm Bolt WH000038
4 Offset Insert TT000870
5Fixed Seat Bolt TT000633
Flag Mount: (Sport Touring Seat only)

800.945.9910 | www.TerraTrike.com
4460 40th St. SE | Grand Rapids, MI 49512 USA
Revised 10/2021