TESY GH 200 W Parts list manual

GH 200 W/ GH 200 BW
220-240V~ 50Hz 2000W
EN GLASS PANEL HEATER 2-9 Usage and Storage Instructions
BG СТЪКЛЕН ПАНЕЛЕН ОТОПЛИТЕЛ 10-18 Инструкции за употреба и съхранение
RO PANOU DE ÎNCĂLZIRE DIN STICLĂ 19-26 Instrucţuni de utilizare şu depozitare
HR ÜVEGPANELES KONVEKTOR 27-34 Upute za uporabu i skladištenje
GR ΥΆΛΙΝΟΣ ΘΕΡΜΟΠΟΜΠΟΣ ΠΆΝΕΛ 35-43 Οδηγιες χρησης και αποθηκευσης
LV STIKLA PANEĻA APSILDĪTĀJS 44-51 Ekspluatācijas un uzglabāšanas instrukcija
RS STAKLENA PANELNA GREJALICA 52-59 нструкции за употреба и складирање
MK СТАКЛЕН ГРЕЕН ПАНЕЛ 60-67 Инструкции за употреба и складирањe
NL GLAZEN PANEELVERWARMER 68-75 Gebruikers en opslaghandleiding
SL OGREVALNA STEKLENA PLOŠČA 76-83 Navodila za uporabo in shranjevanje
www.tesy.com
is a registered trade mark of Tesy ltd.

2Usage and Storage Instructions
EN IMPORTANT SAFETY PRECAUTIONS:
WARNING!
• Please read this manual before operating the appliance
and keep it at a safe place for future reference. In case
the appliance is obtained by a new owner, it should be
transferred together with its manual.
•CAUTION: Children under 3 years of age should be
kept away from the appliance unless they are under
constant supervision.
Children from 3 to 8 years of age are allowed to
operate the on/o button ONLY, provided that the
appliance is installed and ready for operation and
such children have been supervised and instructed in
safe operation of the appliance and they understand
all related risks.
Children from 3 to 8 years of age MUST NOT: connect
the plug to power sockets, make adjustments, clean it
or carry out user maintenance operations.
This appliance can be used by children older than
8 years of age and by people with reduced physical,
sensor and mental capabilities, as well as by people
with insucient experience and knowledge provided
they are supervised or instructed in safe operation
of the appliance and understand the related risks.
Children should not be allowed to play with the
appliance. Cleaning and user maintenance operations
must not be carried out by children without
supervision.
•CAUTION: Some of the appliance parts may get very
hot during operation and thus cause burns to users. In
case there are children and vulnerable people in the
room, special attention should be paid.
•WARNING: In order to avoid
overheating, do not cover the appliance!
• The appliance should not be positioned close under
power sockets!
• If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualied
persons in order to avoid a hazard.
• Before connecting the fan heater, you should check
if the voltage on the technical information plate
corresponds to the voltage of the main electrical
system of the place of use /at home or in the oce/.
The appliance is intended for the voltage, shown on
the technical information plate.
• GH 200 W / GH 200 BW glass panel heater must be
installed in accordance with the good professional
practices and in accordance with the legislature of
the particular state (Electricity Directive of EU and
requirements for special installations and places
of installation including bathroom or shower box
HD60364-7-701:2007(IEC 60364-7- 701:2007)).
• The heater is classied as class II and is provided with IPX4
water protection. For that reason it must be mounted
in position (VOLUME) 2. That prevents the chance of
reach to the control board (switch and thermostat) of the
fan heater by a person who is in a shower or in a bath.
Minimum permissible distance between the appliance
and a water source must not be less than 1 meter! The
appliance is to be mounted on a wall only!
This appliance must be used only with its main function,
which it was intended for, i.e. heating of domestic
premises. Every dierent usage is considered incorrect
and hence dangerous. The manufacturer does not assume
responsibility for break-downs, caused by incorrect
and unreasonable usage. Non-adherence to the safety
precautions will render the guarantee invalid
• Do not leave your home, while the appliance is
turned on: assure that the switch is in position
OFF(0) (turned-o) and the thermostat switch is in
position – minimum. Always disconnect the plug of
the device from the socket.
• Keep inammable objects as furniture, cushions,
bedding, paper, clothes, curtains etc. at a distance of
minimum 100 cm away from the fan heater.
• Do not use the device in areas of usage and storage
of inammable substances. Do not use the device in
combustible areas /for example near inammable gases
and aerosols/ - there is a great risk of explosion and re!
• Do not insert or allow any objects to get into the
ventilation openings (inlets and outlets), because
that can cause break-down of the appliance or any
other damages.
• The appliance is not suitable for animal breeding
and is intended only for domestic use!
• Keep the air outlet free from any objects: you should
keep a clear distance of at least 1m in front the
heater. Do not allow any objects to get into in the
air inlet or outlet because that can cause electrical
shock, re or damage of the heating element.
• The most common reason for over-heating is the

Usage and Storage Instructions 3
EN
English
accumulation of dust and dirt in the appliance.
You should clean regularly ventilation openings
with a vacuum cleaner. Before cleaning you must
disconnect the appliance from the mains. Keep the
fan heater always clean.
• You should never touch the appliance with wet or
moist hands – there is danger for your life!
• In order to disconnect the plug from the socket
outlet when necessary the socket should be
accessible all the time!
• You must never pull the electric cord or the
appliance itself when disconnecting from the mains
• Warning! The air outlet gets hot when the appliance
is operating (more than 80°).
• Do not cover the appliance. If the appliance is
covered there is danger of overheating.
• The electrical system to which the appliance is
connected must be provided with automatic safety
fuse. The distance between the sockets and the
appliance (in turned-o state) must be at least 3mm.
• Grounding is forbidden! After unpacking and before
use you must check if the mechanical parts and
their gear are in a good state. If you have any doubts
you should not use the appliance and search advice
from a qualied electrician.
• If the appliance is damaged or not functioning
properly you must stop it and not try to repair it
yourself. For any type of repairs you must consult
the Service Center for post-sale help. There you
will have your damaged part replaced with an
original spare one. Not obeying this instruction will
compromise the appliance safety.
• If you decide to stop using an appliance of that kind
it is recommended to make it unusable as you cut
the electric cord, after you have disconnected it
from the mains. It is also recommended all hazards,
related to the appliance to be checked. That is
very important if there is a chance the discarded
appliance to be used for play by children.
• You should never keep the appliance unnecessarily
plugged-in. Disconnect the appliance from the
mains if you do not intend to use it for a long time.
• In order to avoid any overheating of the electric cord
it is recommended to unreel the whole electric cord.
•Warning: Do not use this appliance with a programmer,
counter or another device which can automatically turn
it on because if the appliance is covered or incorrectly
positioned there is a danger of re.
• Place the electric cord in such a way that it does
not hamper the movement of people and not
to be stepped on! You must use only approved
connection blocks, which are suitable for the
appliance, i.e. there is a sign of compliance!
• The electric cord must not be in touch with the hot
parts of the appliance!
• You must never move the appliance by pulling it by
its electric cord. You must never use the electric cord
for moving of other objects.
• Do not reel the electric cord round the appliance!
Do not use the appliance with its electric cord
reeled – this is also valid if a cable drum is used!
• Do not press the cord and do not stretch it by sharp
edges. Do not place the cord over hot plates or in
open re!
• This appliance is intended only for drying textiles
washed in water.
PACKAGE
• After unpacking the appliance you should check if
it is not damaged during transportation and if all
the components are included! In case that you nd
out any damage or incomplete package you should
connect with your authorized retailer!
• Do not discard the original packing box! It could be
used to store the appliance during transportation in
order damages to be avoided!
• The disposal of the packing material should be
done in the appropriate way! Children should be
prevented from playing with the polyethylene bags!
MOUNTING ON A WALL
1. Please ensure that the walls of the installation
location without wires, pipes, etc., to ensure that the
device can be securely mounted on the wall
2. The appliance is intended only for vertical wall
mounting! Floor or ceiling mounting is forbidden!
3. Never position the appliance right below a socket
outlet!
4. The appliance should be assembled and connected
by a qualied electrician. The installation process
should be isolated from the mains before electrical
connection works are to be done.
5. Position the power cord so that it does not hamper
free movement of people and not to be stepped on!
Use only approved extensions, which are proper to
the appliance, i.e. they have a compliance sign!
6. The power cord should not be in touch with hot
parts of the appliance!
7. Do not use the appliance in rooms smaller than 4
square meters.
8. The appliance inlet and outlet openings must not
be blocked! Distance between the appliance and

4Usage and Storage Instructions
EN the ceiling is at least 0.2m. Distance on both sides of
the appliance to the wall is at least 0.25m. Distance
between the outlet and the bottom is min 0.5m.
FIXATION OF THE APPLIANCE ON WALL
1. Choose a wall on which there is enough space
2. Use a Ø6 drill to drill 4 holes according to following
positions:
3. Fit the pegs from the accessory bag in these holes.
4. Detach the up-hook from the back of the appliance
and put it in the position of the two pegs at the top.
Fix the up-hook on wall with two ST4X35 screws.
5. Insert the two lters in the left and right card slot,
tighten them with two ST3X10 screws (notice for the
screw position).
6. Put the two Z wall hanging brackets on the back of
the appliance with two M4X8 screws, put the small
towel rack into the xed slot and lock with four M4X16
screws, and then put the big towel rack into the xed
slot and lock with four M4X16 screws.
7. Assemble the appliance on the up-hook, tighten two

Usage and Storage Instructions 5
EN
English
M4X10 screws on the right side and two M4X10 screw on
the left side to x the appliance (two people to assemble).
8. Fix the Z wall hanging brackets on the wall with two
ST4X35 screws
9. Use the cloth to clean the surface.
We thank you for choosing GH 200 W/ GH 200 BW glass
panel heater. The appliance will provide long-life service
if being correctly maintained and taken care of in
accordance with the manual.
TECHNICAL SPECIFICATIONS
Model GH 200 W / GH 200 BW
Rated Voltage 220-240V~
Rated Frequency 50 Hz
Rated Power 2000W
Protective Class II
IP rating IPX4
OPERATION INSTRUCTION

Mode

Prog

ON


+

-
1
2
3
4
5
6
7
C
O
O
O
O
N
N


DISPLAY AND BUTTON
Plug in supply of 220-240V~ 50Hz, push the ON/OFF
(0/I) button located at the left side of the heater to
TOWER RACK
Up and down
sliding
Tower Rack
Glass Panel
Body sensor
Display
Touch button
Week
day
Body
sensor
PTC
power
setting
Value
Increase 24H
Timer
Mode
Setting Program
Setting
ON/
STANDBY
Window
open
detection
PTC
Heating
Power
setting
Week
timer
Anti-frost
Panel
heating Value
Decrease
Panel
Heating/
Window
open
detection

6Usage and Storage Instructions
EN switch it on. Buzzer will have a short“D”sound. Display
and button will light up for 10s.
To switch the appliance o, push ON/OFF (0/I) button
again and disconnect the plug.
Touch

once to turn on heating.
Note: Button light will go out in 10s when no
operation is conducted. Touch any button could
reactivate the button light.
Touch

once again to turn o heating & appliance
stay at standby mode.
Note: Motor will continue working for extra 60s to
drive away the residue heat inside unit before
turning o.
1. Set local day and time
At the rst time usage, icon will keep ashing to
remind user to set local day and time before further
operation.
Long touch

button for 3 seconds to activate timer
setting, gure 1 of
1
2
3
4
5
6
7
will ash, touch

+
+
or

--
to select the day, the selected gure will
ash accordingly. Touch

to conrm day setting.
Then come to hour-setting, ashes , touch

++
or

--
to select the hour among 0-23, touch

to
conrm hour setting. Then come to minute-setting,
ashes, touch

++
or

--
to select the minute among
0- 59. Touch

to conrm minute setting.
Note: Program will automatically return to initial
display in 10s when no operation is conducted
during setting.
2. Power Setting
Power Icon
Display
Function
PTC heating
high power
1800W Room
heating
PTC heating
low power
900W Room
heating
Panel
Heating
200W
ON

Towel
heating
Full power 1800W +
200W
= 2000W
ON

Room
heating
+towel
heating
• PTC heating (1800W): Touch

button to turn
on the appliance. Both icons light up, PTC
heating is working at high power 1800W. Touch

once to switch it low power 900W, only one icon
lights up.
• Panel Heating (200W): Touch
ON

once to start
panel heating
• Full power heating (2000W): When panel heating
works, touch

to switch PTC heating at high
power 1800W. Then total power is 2000W.
Note: At this stage, touch

will switch PTC
heating from high power – low power – no power
(1800W- 900W- 0W)
WARNING: The glass surface and air outlet bottom
will become very hot. Be careful and avoid touching it.
3. Temperature Setting
After power is set, touch

++
or

--
to set
temperature among 5-40°С. Display screen will
change accordingly. Once temperature is set, the setting
will be conrmed in 5s automatically.
When ambient temperature reaches the set
temperature, appliance will stop heating.
When ambient temperature drops 1° lower than the
setting, appliance will resume heating to keep the
ambient temperature at set level.
Note: Set temperature must be higher than ambient
temperature. Or appliance will not start heating.
4. Mode Setting of Week Timer - Auto Start
In standby mode, touch

Mode
button to switch working
mode among P1- P2-P3-P4-P5- UP, then touch

Prog
to
conrm setting.
4.1. P1, P2, P3, P4, P5 modes are default program for
quick setting
•P1: all day comfort mode
•P2: mode for general family
•P3: mode for working oce
•P4: mode for commercial plaza
•P5: mode for family on travel or trip

Usage and Storage Instructions 7
EN
English
Week day
Mode
Working mode
Antifrost
Comfort
Antifrost
Comfort
Antifrost
Comfort
Antifrost
1-7 P1
00:00- 24:00
1-5
P2
00:00- 06:30 06:30- 08:30 08:30- 17:00 17:00- 22:30 22:30- 24:00
6-7
00:00- 07:30 07:30- 10:00 10:00- 12:00 12:00- 14:00 14:00- 17:00 17:00- 22:30 22:30- 24:00
1-5
P3
00:00- 06:00 06:00- 17:00 17:00- 24:00
6-7
00:00- 24:00
1-7 P4
00:00- 06:00 06:00- 22:00 22:00- 24:00
1-7 P5
00:00- 24:00
4.2. UP mode is week timer setting of comfort / anti-
frost set by end-user.
Once UP mode setting is activated, gure 1 (Monday)
of
1
2
3
4
5
6
7
and begin ashing,
light up.
Example 1 - set one or three (at most) time-range at
comfortable level, then follow steps as below,
Touch

++
or

--
, LED display 1(1st working-hour)
& ashes. Touch

++
or

--
to select the start time
of 1st working-hour among 0-23. Once selected, touch

to conrm it. Touch

++
to set end time. Then touch

to conrm 1st setting.
Note: it must be at least 1 hour more than start time.
LED turn to display 2(2nd working-hour), repeat the
same steps of 1st working hour to set 2 more time-range at
most upon your need.
After one day setting is nished, gure 2(Tuesday)
of
1
2
3
4
5
6
7
begin ashing, repeat the same
steps above to set working hour of each day among
1
2
3
4
5
6
7
.
Example 2 - Touch

directly instead of

++
or

--
,
to leave that day at anti-frost function,
Note: each step must be operated within 2 min, or it
will exist setting and screen will recover to initial display.
Anti-frost: appliance keep room temperature at default
5° to prevent frost.
Comfort: comfortable level achieved by setting power
and temperature upon need. (Reference to step 2&3)
5. Body Sensor
Once UP mode is set, body detector will be activated at
the same time. Icon will light up.
When the pre-set timing of week timer comes,
appliance will start heating. At the rst 15 minutes, if
no absence is detected in the room, appliance will stop
heating and stay at standby mode. Once body sensor
nds any come-in person, the appliance will start
heating again.
Note: Body detector only take eects on comfort
mode. No function in anti-frost mode.
6. 24 Hour Timer – Auto O
In P1 mode, touch

twice quickly to activate 24 hour
timer setting, icon & ash. Touch

++
or

--
to set timer among 0 to 24. Leave the setting for 5s,
stop ashing, stop ashing and will keep lighting
up, timer setting is conrmed. Screen will show
ambient temperature and counting-down hour in turn.
Touch

again could cancel the setting. Screen will
turn to show room temperature.
7. Child Lock Function
In working mode,
long touch

++
and

--
at the same time for 3
seconds to activate child lock function, screen will
show [ ] after setting and will recover to initial display
in 5 seconds. Other function is invalid once child lock
function works. Once button is touch, screen will ash
[ ] to remind you child lock function is working and
recover to initial display in 5 seconds.
Long touch

++
and

--
at the same time for 3
seconds again could cancel child lock function.
8 . Window Open Detection Function:
In any working mode (in spite of anti-frost),
long touch
ON

for 3 seconds to activate window open

8Usage and Storage Instructions
EN
detection, icon ashes on the screen.
Long touch
ON

for 3 seconds again could cancel the
setting, icon disappear.
In window open detection mode, room temperature is
found to drop 5°C in 10 minutes when appliance is heating.
Appliance will consider the window may be open and start
detection. In the next 30 minutes, if room temperature is
found to be the same or lower than before, appliance will
consider the window is open and stop heating. At the same
time, icon stops ashing and keep lighting up to
remind user to close the window.
When the window is closed, touch
ON

to recover normal
operation , icon ashes again.
9. Recovery of Factory Setting
It should touch buttons

++
and

--
at the same time
twice in the working state, the appliance will recover to
initial factory setting.
FILTER CLEAN
Filter becomes dirty during use. Turn the appliance o, then
remove the lter on the back of the appliance. Clean the
lter directly under water. Do not use caustic or abrasive
material during cleaning, as this can damage the lter. Then,
have the lter dried naturally.
Then reassemble the lter according to the reference
line (see below drawing).
Push the lter to the end until it cannot move anymore.
Note: First, use the screwdriver to unscrew two
ST3X10 screws from lter, remove the left and right
lters.
OVERHEATING PROTECTION
The in-built overheating protection automatically turns
the appliance o in case of an error! In that situation
the plug must be disconnected from the mains and the
control switch put in position“0”. After a short period of
cooling the appliance is ready for operation (in about
10-15 minutes)! If that error is repeated – consult an
authorized service at your location!
CLEANING
• You must rst turn o the appliance and disconnect its
plug from the socket. Do not use abrasive detergents!
• Clean the body with wet cloth, vacuum cleaner or
a brush!
• You must never submerge the appliance under
water – there is life danger!
• If the appliance should not be used for a certain
period of time it must be secured from excessive
dirt and dust by placing it in its original package.
• You must never place the hot appliance in its package!
•
Instructions for environment protection
Electric appliances out of use contain valuable
materials and hence must not be disposed in
domestic dumbs! We kindly ask you for cooperation
and active role in preservation of natural resources by
disposing the appliance to the organized buy-back
locations (if there are any).

Usage and Storage Instructions 9
EN
English
TABLE 2: INFORMATION REQUIREMENTS FOR ELECTRIC LOCAL SPACE HEATERS
Model identier(s): 1.GH 200 W/ GH 200 BW 2000W/220-240V~ 50Hz
Item Symbol Value 1. Unit Item Unit
Heat output Type of heat input for electric storage local
space heaters only (select one)
Nominal heat
output
Pnom 2.00 kW Manual heat charge control, with integrated
thermostat
[yes/no]
Minimum heat
output (indicative)
Pmin 0.20 kW Manual heat charge control, with room and/
or outdoor temperature feedback
[yes/no]
Maximum
continuous heat
output (indicative)
Pmax,C 2.00 kW Electric heat charge control, with room
and/or outdoor temperature feedback heat
charge control, with integrated thermostat
[yes/no]
Auxiliary electricity
consumption
Fan assisted head output [yes/no]
At nominal heat
output
elmax N/A kW Type of heat output/room temperature
control (select one)
-
At minimum heat
output
elmin N/A kW Single stage heat output and no room
temperature control
[no]
In standby mode el SB 0.0009 kW Two or more manual stages, no room
temperature control
[no]
With mechanic thermostat room
temperature control
[no]
With electronic room temperature control [no]
With electronic room temperature control
plus day timer
[no]
With electronic room temperature control
plus week timer
[yes]
Other control options (multiple selections
possible)
Room temperature control, with presence
detection
[yes]
Room temperature control, with open
window detection
[yes]
With distance control option [no]
With adaptive start control [no]
With working time limitation [yes]
With black bulb sensor [no]
TESY Ltd - Head oce
1166 Soa, Soa Park,
Building 16V, Oce 2.1. 2nd Floor
PHONE: [phone],
FAX: [phone],
o[e-mail]

10     
BG ВАЖНИ ПРЕДПАЗНИ МЕРКИ И ИНСТРУКЦИИ ЗА
БЕЗОПАСНОСТ:
ВНИМАНИЕ!
•     
      
  .    ,
      
  .
•ВНИМАНИЕ:   -  3 , 
    ,     
 .
    3   8  
    ./.  ,
 ,       
      
     
   ,     .
    3   8   
    ,   ,
      
.
        
  8     
,    ,
     ,  
    
     
.        .
     
      .
•ВНИМАНИЕ:       
      .
 ,     ,
    .
•ПРЕДУПРЕЖДЕНИЕ:    
,   !
•      
   !
•     ,  
       
,    , 
   .
•     ,
    
    
     (). 
     
   .
•   
GH 200 W / GH
200 BW
    
      
   
(     
     
 ,    HD60364-7-
701:2007(IEC 60364-7-701:2007)).
•           
 IPX4.       
  (volume) 2,    
     ( 
)     
        
.      
        1 
      !
•        
,     ,
..    . 
       
 .   
    ,  
   . 
     
    !
•    ,    :
 ,     , 
    . 
     .
•   ,  ,
,  , , ,
  ..     100  
  .
•       
    .
      
 (:    
  ) -   
    !
•        
     (
 ),       
     .
•        ,