Texecom Premier 8SP User manual

Premier 8SP User Guide
USER GUIDE
Security Control Panel
THANK YOU FOR VOTING TEXECOM

Premier 8SP User Guide
2INS236
Operating Your Alarm System
This document covers the everyday operation of your alarm system, for details on
more advanced operation and system programming, please refer to the Premier
8SP Master User Manual.
Away Arming the System
Enter your Access code !!!! followed by the "/#key. The Armed
light will flash and the exit sounder will sound for the duration of the exit time.
Stay Arming the System
Enter your Access code !!!! followed by the $key. The system will
normally arm immediately, the Armed light will flash slowly indicating that the
system is Stay armed.
Disarming During Entry
Enter the premises via the designated entry point. The entry tone will sound,
proceed directly to the remote keypad and enter your Access code
!!!!.
Disarming When Not in Entry
Proceed directly to the remote keypad and enter your Access code
!!!!, the Armed light will turn off.
Bypassing Zones
Enter your Access code !!!! followed by the %key. Enter the zone
or zones to be bypassed e.g. 02, 04 etc. The Ready light will flash slowly
indicating one or more zones are bypassed. When all required zones have been
selected, press:
"/#to Away arm the system with the selected zones bypassed
$to Stay arm the system with the selected zones bypassed
&to return to the normal disarmed state with the selected zones bypassed
Reset Alarms/Faults
Enter your Access code !!!!, then press 'or enter &(.
Last Alarm Log
Enter your Access code !!!!, and then enter &). The remote
keypad will display the zones that caused an alarm when the system was last
armed. Press &to return to the normal disarmed state.

Premier 8SP User Guide
INS236 3
Acknowledging a New Service Fault
Should the Service light start flashing, enter your Access code !!!!,
and then enter &*. The remote keypad will display all Service Faults (see
Service Faults Table on back page). Press &or '+to acknowledge the fault
and return to the normal disarmed state.
Toggle Chime On and Off
Enter your Access code !!!!, and then enter &, or -.
Change User Access Code
Enter your existing Access code !!!!, and then enter &.. Now
enter your new Access code !!!! followed by the "/#key. Finally
re-enter your new Access code !!!! for confirmation.
Abort Communications
Enter your Access code !!!!, and then enter &/.
Operating Your Alarm System with Quick Commands
If your Installer has programmed the Quick Commands the following procedures
can be used:
Away Arming the System
Press the "/#key. The Armed light will flash and the exit sounder will sound
for the duration of the exit time.
Stay Arming the System
Press the $key. The system will normally arm immediately, the Armed light will
flash slowly indicating that the system is Stay armed.
Bypassing Zones
Press the %key. Enter the zone or zones to be bypassed e.g. 02, 04 etc. The
Ready light will flash slowly indicating one or more zones are bypassed. When all
required zones have been selected, press:
"/#to Away arm the system with the selected zones bypassed
$to Stay arm the system with the selected zones bypassed
&to return to the normal disarmed state with the selected zones bypassed

Service Faults Displayed on LED Keypads
Light Fault Condition
1 AC Fail
2 Telephone Line Fault
3 2-Wire Smoke Alarm
4
Box Tamper & Auxiliary Input:
Press ,to view type, Lights 1 - 3 will light up:
Light 1 = Box Tamper
Light 2 = Auxiliary Tamper
Light 3 = Bell Tamper
5 Date or Time Lost
6 Zone Tamper/Trouble
Press 0to view zone number
7 Keypad Tamper/Removed
Press /to view keypad number
8
Equipment Faults
Press 1to view fault type:
Light 1 = Bell Output Fault
Light 2 = Strobe Output Fault
Light 3 = Reserved
Light 4 = 2-Wire Smoke Sensor Fault
Light 5 = Auxiliary Fuse Failed
Light 6 = Battery Fault
Light 7 = Service Timer/Zone Soak Test Failed
Light 8 = Communication Fault
© Texecom Ltd. 2003
INS236