Theben PlanoCentro 000-E Series User manual

1103056503 / 01.2017 © Theben HTS
Art. Nr.
204 0 . . .
PlanoCentro 000-A-230V
PlanoCentro 000-E . .
PlanoCentro 000-U . .
Bedienungsanleitung 2
Notice d'utilisation 30
Operating Manual 58
Manual de instrucciones 86
Istruzioni per l'uso 114
Gebruikshandleiding 142
Bruksanvisning 170
Bruksanvisning 198
Käyttöohje 226
Betjeningsvejledning 254
DK
D
F
GB
E
I
NL
S
N
FIN
Presence detector
Bedienungsanleitung 2
Notice d'utilisation 30
Operating Manual 58
Manual de instrucciones 86
Istruzioni per l'uso 114
Gebruikshandleiding 142
Bruksanvisning 170
Bruksanvisning 198
Käyttöohje 226
Betjeningsvejledning 254
DK
D
F
GB
E
I
NL
S
N
FIN

58
English Operating Manual
Presence detector
PlanoCentro 000-A-230V
PlanoCentro 000-E . .
PlanoCentro 000-U . .
Table of contents
1. Safety.........................59
2. Function and performance .........60
3. Installation .....................62
4. Connection / Operation mode .......66
5. Start-up .......................69
6. Parameters .....................71
7. Read-out data ..................72
8. Test-Mode .....................73
9. Control commands ...............75
10. Diagnostics.....................76
11. Troubleshooting .................77
12. Technical data ..................78
13. Dimension drawings ..............81
14. Warranty declaration..............82

59
GB
Thank you for purchasing a Theben HTS presence detector and putting your trust in us.
1. Safety
!
CAUTION!
Danger of death through electric shock or re!
Installation should only be carried out by a qualied electrician!
Work done on electrical installations may only be conducted by an authorised electrician or
trained persons under the supervision and charge of an authorised electrician according to
electrotechnical regulations!
Observe country-specic safety guidelines for working on electric installations! The voltage
supply must be disconnected before installation!
!CAUTION!
The device is maintenance-free.The warranty terminates if the device is opened or entered with
any kind of object.
1.1 Designated use
The presence detector is intended for indoor installation.
The presence detector is solely intended for the purpose contractually specied between the
manufacturer and the user.Any other or extended use has to be regarded as not complying with
the designated use.The manufacturer is not liable for any resulting damage. Radio frequency has
to be followed.

60
2. Function and performance
The presence detector series PlanoCentro is intended for ceiling mounting.
●Installation in suspended ceilings (false ceilings)
●Installation in ush-mounted junction box (set into concrete ceiling)
Devices are available in the delivery unit with matching assembly sets for ceiling installation and
ush-mount ceiling installation.
The presence detector PlanoCentro 000 (Slave) serves to extend the detection area in combination
with a master device such as PlanoCentro 101. By relaying the presence signal the PlanoCentro
000 helps with the comfortable and energy-efcient control of lighting, HVAC and shading. The
area of preferred use includes large spaces such as ofces and classrooms.
●Detection range up to 100m2moving and 64m2seated persons at 3.5 m installation height
●Adjustable sensitivity
The PlanoCentro 000 has an output for parallel connection.
Helpful functions are available for start up and subsequent maintenance support.
●Data read-out (parameters, diagnostic and statistical data)
●Diagnostic functions
The presence detector can send conguration and diagnostic information to the SendoPro Man-
agement remote control via radio transmission (868MHz). Commands from the SendoClic remote
control cannot be processed.

61
GB
2.1 Scope of delivery
Ceiling installation
1 Presence detector with installation
protection cover (removable)
2 PlanoCap (terminal cover)
3 PlanoFix E (installation frame)
4 Strap, 6 pieces
5 PlanoCover (frame)
6 Template for ceiling cut out
7 Assembly instruction
Flush-mounted installation
1 Presence detector with installation
protection cover (removable)
2 PlanoFix U (installation plate)
3 PlanoCover (frame)
4 4 screws
5 Assembly instruction
1
1
2
2
3
3
4
4
75
5
6

62
o
7 x 7 m
9 x 9 m
o
7 x 7 m
9 x 9 m
seated persons
moving persons
3. Installation
3.1 Presence detection
The ideal installation height is between 2.0 - 3.5 m.The sensitivity of the detector reduces with higher
installation heights. The presence detector requires a clear view of people in order to clearly detect
people. Ofces, mobile partition walls, plants, hanging lighting etc. can hinder (shadowing) the pres-
ence detector.
Detection range (installation height 3.0m)
install. height seated persons moving persons
2.0 m 20 m24,5m x 4,5m 36 m26,0m x 6,0m ± 0.5m
2.5 m 36 m26,0m x 6,0m 64 m28,0m x 8,0m ± 0.5m
3.0 m 49 m27,0m x 7,0m 81 m29,0m x 9,0m ± 1.0m
3.5 m 64 m28,0m x 8,0m 100 m210,0m x 10,0m ± 1.0m

63
GB
3.2 Ceiling installation
Ceiling installation of the presence detector takes place via the PlanoFix E installation frame and
straps in the cut out ceiling element.

PlanoFix E installation frame
1. Draw ceiling cut out 
(A hinge is integrated into the top of the packaging)
2. Cut out the drawn form according to the materials with suitable
tools, 100 x 100 mm ± 1mm 
3. Insert 4 straps into the PlanoFix E 
4. Insert the PlanoFix E into the ceiling cut out with the straps 
5. By pulling on the straps and pushing against the PlanoFix E, the
PlanoFix E is snapped securely into the ceiling element. 
6. Cut the ends of the 4 straps 






64
Monitoring the presence detector
1. Connect wires, see technical data page 76.
2. Fasten cable to the strain relief clamps and remove the excess
3. Fasten the PlanoCap
4. Make sure the locks on the PlanoFix E are open 
5. Insert the presence detector into the PlanoFix E 
6. Close the locks on the PlanoFix E 
7. Remove installation protection
8. Attach the PlanoCover
The technical data is to be followed during assembly and installation.
See page 78 and following.




65
GB
3.3 Flush-mounted ceiling installation
Flush-mounted ceiling installation of the presence detector takes place via PlanoFix U in a ush
mounted socket. Details about the ush mounted socket can be found in the technical data page
78, section ush mount installation. The screws included are intended for installation in the ush-
mounted socked. Suitable pan head screws are to be used for the installation of other materials.
Install presence detector with PlanoFix U
1. Connect wires, see technical data page 78.
2. Insert the presence detector into the ush-mounted junction
box (check the wire progression)
3. Screw the PlanoFix U metal plate tightly to the ush-mounted
junction box
4. Remove installation protection
5. Attach the PlanoCover

66
4. Connection / Operation mode
The presence detector PlanoCentro 000 can be used in combination with a master device such as
PlanoCentro 101 to implement parallel connections.
●Master - slave parallel switching
4.1 General parallel connecting
The parallel signal is sent via P-terminal and also received. Every detector, regardless of whether
it is master or slave, sends the presence signal via P-terminal. This enables a Master and Slaves
to be connected together with a parallel signal. See following chapter with parallel connecting
variations.
-The parallel signal is compatible with the compact range.
Parallel signal response
Room monitoring Information about room monitoring is also transmitted with the parallel signal.
!CAUTION!
Power supply:
Detectors linked to one another via the parallel signal have to be connected
to the same phase.

67
GB
NNLLAPPS1 H2
PlanoCentro
101-A-230V
H1
N
L
NNLL PP
PlanoCentro
000-A-230V
Slave
Master
4.2 Master-Slave parallel circuit operation
Several detectors switch one lighting group
●The Master switches the lighting.All other detectors are slaves.
●Presence detection through all detectors together.
●Light measurement only with master.
●Setting parameters on the Master. Detection sensitivity can also be set on the Slave.
●Maximum of 10 detectors can be connected in parallel.
●Use the same phase for all detectors.
Presence
(e.g. HVAC)
Master: PlanoCentro 101-A-230V
Slave: PlanoCentro 000-A-230V

68
4.3 Parallel circuit operation with external staircase lightning timer
●Master switches lighting directly.
●Master checks the brightness.
●Use the SendoPro to set the lighting
time delay for channel A light at the
Master to impulse.
●Use the same phase for all devices.
●Staircase time switch e.g. Theben
ELPA 1
4.4 Detector as staircase lightning timer
●Master switched direct lighting.
●The staircase function «On» prevents switching off via push-button.
●Push-button activates channel A light
●If necessary, parallel switch ad-
ditional slaves via P-terminal.
●Set parameter value only with
master.
NNLLAPPS1 H2
PlanoCentro
101-A-230V
H1
N
L
Master
N
L
4
3
B 3B 2
ELPA 1
NNLLAPPS1 H2
PlanoCentro
101-A-230V
H1
Master
NNLLAPPS1 H2
PlanoCentro
101-A-230V
H1
N
L
NNLL PP
PlanoCentro
000-A-230V
Slave
Master

69
GB
5. Start-up
The detector is delivered ready for operation with basic settings. The specications are guide
values.The management remote control SendoPro is available as an option for start-up. It enables
remote setting of all parameter values. See chapter 6 page 71.
5.1 Basic settings
Parameter Value
Detection sensitivity (PIR) 3
Reduction of detection sensitivity when monitoring 2
5.2 Activating the basic settings
The basic settings can be activated as follows.
Activation Description
SW2 (3 sec) The SW2 button can be pressed and held down for 3 seconds to revert
back to the basic settings. The presence detector restarts at this point. SW2
SendoPro The basic settings can be adopted with the SendoPro Management
remote control command.

70
5.3 Behaviour on switching on
Every time the voltage is switched on, the detector goes through the start-up phase, which is
indicated by the LED. The presence detector runs through several tests during the start-up phase.
If the tests run without any problems, then the presence detector switched to normal operation
mode. If there is a problem (LED blinks rapidly), the light is switched on and does not switch off.
1. Start-up phase (30 seconds)
●LED blinks in second intervals.
●Parallel output is active
●Parameter adjustment is possible (active after start up phase has run)
●Test mode can be activated.
2. Operation mode normal
●The detector is ready for operation (LED off)
3. Event of malfunction
●LED ashes rapidly
●The light is switched on and does not switch off as long as there is a malfunction
●Troubleshooting see page 77

71
GB
6. Parameters
The basic settings can be adjusted and optimised using the SendoPro management remote control.
The following parameters are available with the PlanoCentro 000-A-230V:
Parameter Page
Operation mode Normal / test presence / test light 71
Detection sensitivity (PIR) Value range in increments 72
Reduction of detection sensitivity when monitoring Value range in increments 72
6.1 Adjustment with the remote control
Parameters are sent to the presence detector via infrared with the SendoPro. The parameters
can be read-out before changes take place. Changed parameters are immediately accepted and
applied by the detector.
LED Description
Flickering during 3 sec After pressing the send function on the management remote control, the presence detector
displays correct receiving by ickering for 3 sec
lights up shortly The command/parameter sent from the management remote control via infrared is rejected by
the presence detector.The command is not valid. Check the selected detector type and the sent
parameters.
6.2 Operation mode
The PlanoCentro has 3 operation modes
●Normal ●Test presence (page 73)

72
6.3 Detection sensitivity
The detector has 5 sensitivity levels. The basic setting is the mid-
dle level (3). A level can be selected with the SendoPro manage-
ment remote control.
By selecting the operation mode test presence, the set sensitivity
level is not changed.
The parameter can be changed during test presence.
6.4 Reducing sensitivity with room monitoring
In order to prevent false alarms, the sensitivity is reduced in levels
relative to the base detection sensitivity.
7. Read-out data
By means of the SendoPro management remote control the diagnostic and statistical data can
be read-out.
Additional information can be found in the SendoPro operation manual.
Level Reduction
1 less
2 Standard
3 intense
Level Sensitivity
1 less sensitive
2 Interim value
3 Standard
4 Interim value
5 very sensitive

73
GB
8. Test-Mode
The PlanoCentro has a test mode.
●Test presence, page 73
The test mode can only be started with voltage supply.
8.1 Test presence
The test presence serves to test presence detection and parallel switching.
The test presence can activated directly on the presence detector (without
power up) or with the SendoPro management remote control.
Activate -Push-button SW2; short button push 1x
-"Test presence on" with the SendoPro management remote control
The test mode presence can always be activated.
Terminate With subsequent restart:
-Repress SW2 ends operation mode and restarts the detector.
-Command "Test presence off" with the SendoPro management remote control
-Power outage and thus power up
-The detector automatically restarts after 10 minutes (see page 70)
LED display Description
On On detection of movement.
Off With insufcient movement or absence.
SW2

74
Test response
-The parallel signal is transmitted via the P-terminal.
-Room monitoring responds normally as in normal mode.
Commands and adjustable parameters
During test mode the following commands are possible with the SendoPro management remote conrol:
-Terminate test presence
-Activate basic settings (Reset)
-Change detection sensitivity
-Change reducing sensitivity with room monitoring
The selected detection sensitivity (1 ..5),see page 72,is not changed with the test presence activa-
tion. Sensitivity can be adjusted during the test.
The presence detector resets after test mode has terminated.

75
GB
9. Control commands
Control commands are available as follows:
Test presence See chapter 8.1 page 73
Restart The detector restarts. Setting values are retained.
Restore basic settings Set settings and conguration to factory settings.

76
10.Diagnostics
10.1 Status information
Diagnostic and statistic information can be read-out by the SendoPro management remote control.
Further information is available in the SendoPro operating instructions.
10.2 Malfunction information
Malfunction information can be read with the SendoPro management remote control.
Error display Solution
Hardware malfunction Send in device for repairs with a short description of the problem to the
responsible specialised dealer.
Parameter error Change and send parameter set
P-terminal overload Fix parallel switching wiring malfunction
10.3 Diagnostic values
The values can be reset using the SendoPro management remote control.
Value Description
Diagnostic Number of parallel
signals
Counts incoming parallel signals.