Theben theRonda P360-330 DALI UP WH User manual

1
theRonda P360-330 DALI UP WH
2080045
307290 02
Presence detector
EN
1. Product characteristics
•Passive infrared presence detector for ceiling installation
•Circular detection area 360° (up to 452 m2)
•Restriction of detection area with cover clips
•Automatic lighting control with constant lighting control
or switching operation
•Lighting dimmable in switching operation with or wit-
hout effect of daylight
•Orientation light (standby function)
•DALI solution for up to 3 exibly addressable lighting
channels
•DALI-2 certied
•Easy, intuitive conguration of DALI groups
•Mixed light measurement suitable for uorescent lamps
(FL/PL/ESL), halogen/incandescent lamps and LEDs
•Adaptable 3-channel light measurement
•Calibration of brightness measurement
•Fully or semi-automatic operation, switchable
•Brightness setpoint value adjustable in lux
•Teach-in function via remote control or button
•Self-learning time delay
•Reduction of time delay when present briey (short-term
presence)
•Detection sensitivity congurable
•1 presence channel for external DALI relay, e.g. for HVAC
control
•Connection option for up to 3 conventional buttons for
manual dimming and switching
•Flexible assignment of buttons to required lighting chan-
nel by remote control
•Behaviour upon button operation selectable
•Scene functionality
•Easy conguration of the energy-saving response with
“eco plus” function
•Test mode for checking function and detection area
•Light test mode for checking the brightness threshold
•Extension of detection area via Master/Slave or Master/
Master switching
•Protection rating IP 54 (installed)
•Ceiling installation in ush-mounted box
•Surface mounting on ceilings possible with back box
(option)
•Management remote control “SendoPro, theSenda B/
App” (optional)
•User remote control “theSenda S” (option)
2. Safety
Danger of death through electric shock or fire!
Installation should only be carried out
by a qualified electrician!
WARNING
•Work on electrical systems may only be carried out by
qualied electricians or by instructed persons under the
guidance and supervision of a qualied electrician in
accordance with the technical regulations applying to
electricity!
•Comply with the country-specic safety regulations for
work on electrical systems! Ensure absence of voltage in
the cable before installation!
•The device is maintenance-free. If the device is opened
or penetrated with any object, the guarantee shall lapse.
3. Proper use
The presence detector is intended for indoor installation. The
presence detector is exclusively intended for use as contrac-
tually agreed between the manufacturer and the user. Any
other use is considered to be unacceptable. The manufacturer
does not accept liability for any resulting damages.
4. Function
The presence detector is primarily used in ofces, schools,
conference rooms and corridors, as well as in homes, for easy
and energy-efcient control of lighting. The lighting is accor-
dingly inuenced by switching or constant lighting control.
Function description






 Mixed light measurement
Presence detection
 Articial light
Push button for manual lighting control
Incident daylight
Lighting channel C1, C2, C3
The lighting is controlled by presence and brightness. Articial
lighting is switched on and regulated at a constant brightness
level via the DALI interface in the event of too little daylight
and when the room is occupied.
The lighting is switched off via the DALI interface if there is
sufcient daylight or if the room is unoccupied.
Up to 3 lighting groups (lighting channels C1 - C3) can be
congured on one single DALI line. DALI devices can be
addressed and grouped very easily and intuitively. A detailed
description can be found in chapter „9. Start-up“.

2
Constant light control
Constant light control compensates for variations in daylight
by controlling the lighting. The overall brightness will be kept
constant at the desired brightness level. The lighting is swit-
ched on with the switch-on dimming value and controlled so
that it reaches the set brightness setpoint value. Depending
on „school“ or „ofce“ conguration type, the presence detec-
tor behaves differently after manual dimming via button:
•„School“ conguration type for applications in classrooms
and meeting rooms:
y Manual dimming deactivates constant light control.
y Lighting remains at dimmed level when room is occupied
(no brightness inuence).
y Switching off and on returns to standard operation.
•„Ofce“ conguration type for applications in small and
large ofces:
y Constant light control remains active temporarily after
manual dimming to the current brightness value as the new
brightness setpoint value.
y The new brightness setpoint value only applies if the room
is occupied.
y After the lighting time delay expires, the originally set
brightness setpoint value is restored.
Switching operation
Switching response is controlled by presence and brightness.
The channel light switches on in darkness and if presence
is detected. The light switches off when there is sufcient
brightness or once the room is vacated after the set lighting
time delay. The light is switched on with the switch-on dim-
ming value. By using the button, the intensity of articial light
can be changed for the duration of the presence. Following
override using the button, the light stays on for at least 30
min. The light is forced off after a preset time delay if the
room was (previously) vacated.
Standby (orientation light)
The standby function acts as an orientation light. After the
lighting time delay expires, the lighting is set to the standby
dimming value (1 – 25 %) of the lamp output. The standby
time can be set to between 0 s and 60 min or permanently.
The lighting is switched off if the brightness level in the room
exceeds the brightness setpoint value. The lighting automati-
cally returns to the standby brightness if the room brightness
falls below the brightness setpoint value. When the room
is entered again, the detector returns to the programmed
brightness setpoint value, either automatically (fully automa-
tic device) or after the button is operated (semi-automatic
device).
Lighting time delay
The minimum time delay (10 s – 60 min) is adjustable. It
adjusts automatically to the user‘s behaviour and can incre-
ase to 30 minutes or drop back to the set minimum time.
With settings ≤ 2 min or ≥ 30 min, the time delay remains
unchanged at the set value. If someone goes into an unoccu-
pied room only briey and leaves it within 30 seconds, then
the lighting will be switched off prematurely after 2 minutes
(short-term presence).
Push button control
The lighting can be manually switched or dimmed at any time
at the push of a button. A short press of the button switches
the light on or off, a longer press of the button dims the ligh-
ting up or down. The dimming direction changes each time
the button is pressed. If the lighting is switched off manually,
the lighting will stay off as long as the room is occupied. The
lighting switches on again automatically after the time delay
has expired. Please pay attention to the differing behaviour of
the constant light control and the switching operation, which
is described in the corresponding chapter.
Fully or semi-automatic device
Lighting control via the presence detector operates fully
automatically for increased comfort or semi-automatically for
greater energy savings. The lighting switches on and off auto-
matically as a “fully automatic device”. As a “semi-automatic
device”, the lighting must always be switched on manually.
The lighting is switched off automatically.
Exceptionally easy configuration of the energy-saving beha-
viour
By using the selection “eco” for optimal switching behaviour
or “eco plus” for maximum energy savings, users can adjust
the presence detector to their needs.
5. Detection area
The circular detection area of theRonda P presence detector
covers a large detection area, and permits a complete room
coverage with many applications. Note that seated and wal-
king persons are detected in different areas. The recommen-
ded installation height is 2 m – 6 m. As installation height
increases, the sensitivity of the presence detector decreases.
Walking motions are necessary from installation heights of
3.5 m, and the detection areas of several detectors should
overlap in the marginal zones. The detection range is reduced
as the temperature increases.
Seated persons:
The presence detector reacts very sensitively to the slightest
movements. The information refers to table height (approx.
0.80 m).
S
t
r
s
12
4
3
3412

3
Installation
height (A)
Moving persons
Across (t)
Moving persons
Frontal (r)
Seated persons
(s)
2,0 m 380 m2Ø 22 m 28 m2Ø 6 m 16 m2Ø 4,5 m
2,5 m 415 m2Ø 23 m 38 m2Ø 7 m 24 m2Ø 5,5 m
3,0 m 452 m2Ø 24 m 50 m2Ø 8 m 28 m2Ø 6 m
3,5 m 452 m2Ø 24 m 50 m2Ø 8 m 38 m2Ø 7 m
4,0 m 452 m2Ø 24 m 50 m2Ø 8 m – –
5,0 m 452 m2Ø 24 m 50 m2Ø 8 m – –
6,0 m 452 m2Ø 24 m 50 m2Ø 8 m – –
10,0 m 491 m2Ø 25 m 50 m2Ø 8 m – –
All  gures are guidance values (Detection areas according to sensNORM
IEC 63180, see data sheet).
Brightness measurement
The presence detector measures arti cial light and daylight
by means of three directed light measurements. The central
light measurement detects the brightness directly below the
detector (A), while the two other light measurements detect
the brightness close to the window (B) or in the interior (C).
The installation location is the reference point for the lighting
level. The brightness measurement can be adapted to the
conditions in a room with the room correction factor.
~ 1,8 m ~ 1,8 m
1
C B
A
Each light measurement area maps a rectangle of about 2.0 x
3.5 m at table height. Depending on the operating mode, the
light measurements are assigned as followed:
•2-channel: Window light measurement (B) is perma-
nently assigned to lighting channel C1 and interior light
measurement (C) to lighting channel C2
•3-channel: As with 2-channel, but with free choice
between central light measurement (A) and integral light
measurement (average of light measurements A + B + C)
in the case of lighting channel C3
Switching
Direct light in uences the light measurement. Avoid placing
 oor lamps or suspended lighting directly below the detector.
Constant light control
The detector must be positioned in such a way that it only
detects arti cial light that it controls itself. Arti cial light that
is controlled by other detectors or manually switched work
lighting in uence the brightness measurement of the detec-
tor. The detector must not be exposed to direct arti cial light.
Switching operation
If the brightness measurement is deactivated, the light only
comes on when presence is detected (brightness setpoint
value set to “measurement off” via the remote control).
Suitable lamps
The presence detector is designed for the operation of  uo-
rescent lamps, compact  uorescent lamps, halogen/incande-
scent lamps and LEDs.
6. Installation
LNote window / interior alignment!
Flush-mounted  tting
The presence detector is  ush-mounted using a size 1 stan-
dard  ush-mounting installation socket.
Ceiling installation
A ceiling installation box 73A is available for a simpli ed
ceiling installation of the presence detector (see accessories).
This also ensures cord grip and contact protection. The instal-
lation diameter is 72 mm (drill diameter 73 mm).
Surface-mounted installation
A back box 110A is available for surface mounted installation
(see accessories).

4
7. Connection
The presence detectors can be combined as master in
individual switching, master/master in parallel switching or
master/slave parallel switching. Several push buttons can be
connected to one control input. Illuminated push buttons can
only be used with neutral conductor connection.
With the management remote control „SendoPro, theSenda
B/App“, lighting channels C1 to C3 can be assigned to the
required button inputs S1 to S3 via the parameter <Terminal
SX assignment>. The input S3/P can be used for the master/
slave parallel signal or master/master switching, or as button
input S3. The factory setting is „Parallel“.
Up to 50 DALI operating devices can be connected to each
master device. We recommend distributing the DALI operating
devices equally over the 3 external conductors.
LAll detectors and buttons must be connected to the same
external conductor.
LConnect at least 1 Dali operating device per master.
Individual switching
In individual switching, the presence detector, as master,
detects presence and brightness and controls lighting.
Master
DALI
DA+ DA–S1 S2
EVG
S3/PNL
N
L
EVG
Master/Slave parallel switching
If the detection area covered by one presence detector is
insufcient (larger rooms), then up to 10 detectors can be
operated in parallel by connecting the P terminals. In the
process, presence detection is performed by all detectors
together. The master measures the brightness, operates the
buttons and controls the lighting. All other detectors are used
as slaves. They only provide presence information.
Master
DALI
DA+ DA–S1 S2
S3/PNL
Slave
PNL
N
L
EVG
•Light measurement only with the master
•Switch up to 10 detectors in parallel
•Use the same external conductor for all detectors and
buttons
•Slave: theRonda P360 Slave (2080080)
Master/master parallel switching
Several masters can be used in parallel switching. Each
master controls its lighting groups according to its own
brightness measurements. Time delays and brightness
setpoint values are set individually on each master. Presence
continues to be detected by all detectors.
Master
DALI DALI
DA+ DA–S1 S2
S3/PNL
N
L
EVG
Master
DA+ DA–S1 S2
S3/PNL
EVG
•Master with 2 lighting groups and individual brightness
measurement
•Switch up to 10 detectors in parallel
•Use the same phase for all detectors and buttons
Integrating an external DALI relay
•No more than 1 external DALI relay can be connected
on one single DALI line. The Dali relay must comply with
Standard IEC 62386-208 (device type 7).
•The detector automatically detects the DALI relay.
•Switch-on delay and time delay can be set using the
remote control.
Master
DALI
DA+ DA–S1 S2
EVG
NL
N
L
EVG
DALI
relay
8. Settings
The presence detectors are supplied with basic settings ready
for operation. The specications are guidance values. The
optional “SendoPro, theSenda B/App” management remote
control or the “theSenda P” installation remote control are
available for start-up support. They enable remote setting.
The “SendoPro, theSenda B/App” can be used to query, adjust
and optimise parameters. With the “theSenda P”, parame-
ters can only be adjusted. A range of variable parameters is
available for adjustment with the remote control (see section
“Parameters via remote control”).
Settings via the button
Pressing any button for longer than 15 s triggers the teach-in
of the brightness setpoint value by the teach-in function. In
addition, the teach-in function can be conveniently executed
with the “SendoPro, theSenda B/App” management remote
control or the “theSenda P” installation remote control (see
section “Control commands via remote control”).
The teach-in function via the button can be disabled using
the “SendoPro, theSenda B/App” management remote control
when the <Conguration button/RC> parameter is set to
“disabled”.

5
The lighting groups can also be congured using the but-
tons. All connected buttons can be used for conguration. A
detailed description can be found in chapter „9. Start-up“.
Conguration via the buttons can be disabled using the “Sen-
doPro, theSenda B/App” management remote control when
the <Conguration button/RC> parameter is set to “disabled”.
Parameters via remote control
The following parameters can be checked or changed via
the remote control for support during start-up as well as
servicing:
Parameter Description Can be
checked
SendoPro,
theSenda
B/App
Can be
changed
SendoPro,
theSenda
B/App
Can be
changed
theSenda
P
Function C1/C2
Function C3
Selection:
switching/control x x
Light measure-
ment source C3
Selection: Centre /
Integral x
Terminal S1
assignment
Terminal S2
assignment
Selection: C1 /C2 /
C1+C2 /C3 /C1+C3
/C2+C3 /C1+C2+C3
x
Terminal S3/P
assignment
Selection: Parallel /
C1 /C2 /C1+C2 /
C3 /C1+C3 /C2+C3
/C1+C2+C3
x
Brightness set
point value
C1, C2
Value range in lux/
measurement off x x x
Brightness set
point value C3
Value range in lux/
measurement off x x
Brightness
actual value C1,
C2, C3
Query brightness
actual value x
Room correc-
tion factor Win
Room correction
factor on side
towards window
x x
Brightness
measurement
value Win
Lux meter bright-
ness value on side
towards window
in lux
x x
Room correc-
tion factor Mid
Room correction
factor middle x x
Brightness
measurement
value Mid
Lux meter bright-
ness value middle
in lux
x
Room correc-
tion factor Inn
Room correction
factor Inn x x
Brightness
measurement
value Ins
Lux meter bright-
ness value interior
in lux
x
Room correc-
tion factor Int
Room correction
factor Integral x x
Brightness
measurement
value Int
Lux meter bright-
ness value Integral
in lux
x
Detection sen-
sitivity (PIR)
Value range in
increments x x x
Lighting time
delay
Value range in
seconds and
minutes
x x
Short presence Short-term pre-
sence: On/Off x x
Energy saving
mode
Selection: eco/eco
plus x x
Presence
switch-on delay
Value range in
seconds/minutes x
Presence time
delay
Value range in
seconds/minutes x x
Parameter Description Can be
checked
SendoPro,
theSenda
B/App
Can be
changed
SendoPro,
theSenda
B/App
Can be
changed
theSenda
P
Switch-on
dimming value
C1, C2, C3
Value range in % x
Conguration
type C1/C2 Selection: auto/man x x x
Conguration
type C3 Selection: auto/man x x
Control speed Selection: standard/
medium/fast x
Minimum dim-
ming value Value range in % x
Maximum dim-
ming value Value range in % x
Switching off
brightness
Value range in
minutes/hours/
never off
x
Manual dim-
ming response
Selection: school/
ofce x
Standby time
Value range in
seconds/minutes/
Permanently on
x
Standby dim-
ming value Value range in % x
IR group
address C1,
C2, C3
Selection: All/I/II/III x
Scene 1 C1
Scene 2 C1
Scene for lighting
channel C1 value
range in %
x
Scene 1 C2
Scene 2 C2
Scene for lighting
channel C2 value
range in %
x
Scene 1 C3
Scene 2 C3
Scene for lighting
channel C3 value
range in %
x
Conguration
button/RC
Selection: enabled/
disabled x
LED display
motion Off/On x
The parameters are sent to the presence detector with the
“SendoPro, theSenda B/App” management remote control or
with the “theSenda P” installation remote control via infra-red.
Changed parameters are applied and used by the detector.
LEnsure that the parameter selection is limited on the „the-
Senda P“ remote control.
With the “SendoPro, theSenda B/App” management remote
control, parameters can be queried by sending values level-
by-level to the detector. If the sent value is below the set
parameter, the LED illuminates briey. If the sent value is
equal to or above the set parameter, the LED ickers for 2 s.
Function C1, C2
The lighting channels C1 and C2 can be operated together in
the switching operation or constant lighting control function.
Settings are made via the <Function C1/C2> parameter.
Value range (with SendoPro, theSenda B/App)
Switching Lighting channels C1 and C2 are in the switching operating
function
Control Lighting channels C1 and C2 light are in the constant lighting
control function

6
Function C3
Lighting channel C3 can be operated independently from
lighting channels C1 and C2 in the switching operation or
constant lighting control function. Settings are made via the
<Function C3> parameter.
Value range (with SendoPro, theSenda B/App)
Switching Lighting channel C3 is in the switching operating function
Control Lighting channel C3 is in the constant lighting control function
Light measurement source C3
The presence detector measures articial light and daylight
by means of three directed light measurements, see section
„Brightness measurement“ on page 3.
In the case of 2-channel operation, the window light mea-
surement (B) is permanently assigned to lighting channel C1
and interior light measurement (C) to lighting channel C2.
In the case of 3-channel operation, in addition, the central
light measurement (A) or integral light measurement (average
of all 3 light measurements) is assigned to lighting channel
C3.
Value range (with SendoPro, theSenda B/App)
centre Lighting channel C3 uses the central light measurement (A),
spot metering.
Integral Lighting channel C3 uses the average of all 3 light measure-
ments (A + B + C).
Terminal S1 assignment, terminal S2 assignment,
terminal S3/P assignment
Button terminals S1 and S2 can be assigned to the required
lighting channel at any time, without any need for rewiring.
Terminal S3/P can be used in two different ways. Either but-
tons or the parallel signal for master/slave or master/master
parallel switching can be connected. The required assignment
is carried out via the parameter <Terminal S3/P assignment>.
Value range (with the SendoPro, theSenda B/App)
Parameter Master/
slave or
master/
master
Lighting channel
Terminal S1
assignment
C1 C2 C1+C2 C3 C1+C3 C2+C3 C1+C2+C3
Terminal S2
assignment
C1 C2 C1+C2 C3 C1+C3 C2+C3 C1+C2+C3
Terminal
S3/P
assignment
Parallel C1 C2 C1+C2 C3 C1+C3 C2+C3 C1+C2+C3
Further information can be found in chapter “4 Function”, in
the “Lighting channel C1, C2, C3” section on page 1.
Brightness set point value C1, C2, C3
The brightness setpoint value denes the minimum required
brightness. The currently prevailing brightness is measured
below the presence detector. If the prevailing brightness is
below the setpoint value, the light is switched on when a
presence is detected (in conguration type fully automatic
device).
A separate brightness setpoint value is available for each
lighting channel C1, C2, C3.
Value range
•Lux values with “SendoPro, theSenda B/App” manage-
ment remote control: 10 – 3000 lux, measurement off
•The following values are available with the “theSenda
P” installation remote control: 10, 15, 300, 500, 800 lux,
measurement off ( button), only for lighting channels
C1, C2!
•The currently measured brightness value (lux) can be
adopted as a new brightness setpoint value with the
”SendoPro, theSenda B/App” management remote con-
trol by using the teach-in control command, or with the
“theSenda P” installation remote control via the teach-in
button (also see table Control commands via remote
control). Values outside the permitted range will automa-
tically be set to the appropriate limit value.
•Deactivation of the brightness measurement (the bright-
ness has no effect). The lighting channels only switch
after presence/absence. Possible with the «SendoPro,
theSenda B/App» management remote control (measu-
rement off) or the „theSenda P“ installation remote con-
trol (button ). With „theSenda P“ only lighting channel
C1, C2 is possible!
Brightness actual value C1, C2, C3
For monitoring purposes, all 3 brightness actual values can be
checked. Checks are described on page 5.
Room correction factor Win, Mid, Inn, Int
brightness measurement value Win, Mid, Inn, Int
The room correction factor is a measurement for the diffe-
rence of the brightness measurement on the ceiling and the
work area. The brightness value on the ceiling is inuenced
by the installation location, the incidence of light, the position
of the sun, the weather conditions, as well as the reection
properties of the room and the furniture.
With the room correction factor, the measured brightness
value of the corresponding lighting channel is adjusted to
the conditions in the room and in this way can be matched to
the lux meter value measured at the surface beneath the
presence detector.
~40°
~1,8 m ~1,8 m
~40°
1,5 x 3,5 m 2 x 3,5 m 1,5 x 3,5 m
Installation height 3 m
Figure at table height (0.8 m)

7
Room correction factor = Brightness value at the ceiling
Brightness value on the work
surface
We recommend the following procedure:
 Dim all lights as far as possible. If possible, close blinds.
 The lux meter is placed on the work surface below the
sensor and the measured lux value is entered via the
“SendoPro, theSenda B/App” management remote
control, <brightness measurement value Win, Mid, Inn,
Int> parameter is entered and sent to the detector. During
lux measurements, observe the distances shown in the
diagram. Carry out all measurements at table height.
•<Brightness measurement value Win>: Lux measurement
towards the window
•<Brightness measurement value Mid>: Lux measurement
in the middle (below detector)
•<Brightness measurement value Inn>: Lux measurement
towards the interior
•<Brightness measurement value Int>: Average of all 3 lux
measurements Win + Mid + Inn.
 The room correction factor is calculated from this
automatically. Values between 0.05 and 2.0 are permitted.
Calculated or entered values outside the permitted range
will automatically be set to the appropriate limit value.
 The calculated room correction factor will be applied
immediately. For monitoring purposes, the room correction
factor can be queried via the <room corr. factor Win, Mid,
Inn, Int> parameter.
LThe standard value is 0.3 and is suitable for most appli-
cations. Changes are only sensible in strongly deviating
situations.
Detection sensitivity
The detector has 5 sensitivity increments. The basic setting is
the middle increment (3).
Increments 1 to 5 can be selected and sent to the detector
with the “SendoPro, theSenda B/App” management remote
control. On the “theSenda P” installation remote control, the
sensitivity can be decreased by one increment each time the
button is pushed or increased with the button.
Value range
Incre-
ment
Sensitivity
1Very insensitive
2 Insensitive
3 Standard
4 Sensitive
5Very sensitive
By selecting the test presence operating mode, the set sensi-
tivity increment is not changed.
Lighting time delay
The time delay applies jointly to all lighting channels.
Value range
Adjustable values with “SendoPro 868-A” manage-
ment remote control
10 s – 60 min
In the “theSenda P” installation remote control, the
following values are available 10 s (button ),
30 s, 60 s, 2 min,
10 min, 20 min,
60 min (button )
Short presence
If someone goes into an unoccupied room only briey and
leaves it within 30 seconds, then the lighting will be switched
off prematurely after 2 minutes (short-term presence). The
short-term presence can be used for the fully automatic and
semi-automatic conguration types.
Value range (with SendoPro, theSenda B/App)
The time delay is applied according to the set time delay. Off
Short-term presence is active. On
Energy saving mode eco/eco plus
The selection of “eco” stands for optimum switching behavi-
our, while “eco plus” stands for maximum energy saving.
Value range (with SendoPro, theSenda B/App)
“eco” The time delay adjusts to the user behaviour by self-learning.
It does not drop below the set value.
“eco plus” The set time delay remains unchanged (no self-learning
effect). Faster response to brightness detection than with
“eco”.
Presence switch-on delay
The contact of the external DALI relay closes when some-
one is present regardless of the brightness and after the set
switch-on delay has elapsed. Buttons and the conguration
type (fully automatic device/semi-automatic device) do not
affect the relay contact.
Value range (with SendoPro, theSenda B/app)
No switch-on delay 0 s
Switch-on delay 10 s – 30 min
Presence time delay
The relay contact of the external DALI relay only opens once
the set time delay has elapsed in periods of absence.
Value range
Adjustable values from Sendo-
Pro/theSenda B/app
10 s – 120 min
Adjustable values from theSenda
P
10 s, 30 s, 60 s, 2 min, 10 min, 20 min,
120 min
Switch-on dimming value C1, C2, C3
The lighting is switched on with the switch-on dimming value
in both the switching operation and constant light control.

8
Value range (with SendoPro, theSenda B/App)
Switch-on dimming value C1, C2, C3 30 – 100 %
Conguration type C1/C2
Fully automatic device: the lighting switches on and off auto-
matically. (Due to presence, absence and brightness)
“SendoPro, theSenda B/App”
“theSenda P”
auto
Button A
Semi-automatic: Lights must always be switched on manually.
Lights are switched off automatically by the presence detec-
tor. (Due to presence or brightness)
“SendoPro, theSenda B/App”
“theSenda P”
man
Button
Conguration type C3
Value range (with SendoPro, theSenda B/App)
Fully automatic device: the lighting switches on and off automa-
tically (depending on presence, absence and brightness) auto
Semi-automatic: Lights must always be switched on manually.
Lights are automatically switched off by the presence detector
(due to absence or brightness) man
Control speed
In the constant light control function, the speed of the
constant light control can be set with the <control speed>
parameter.
Value range (with SendoPro, theSenda B/App)
Response is set to its optimum level. The control happens
gradually and is almost imperceptible.
Standard
The control is slightly faster. average
The control is fast. fast
Minimum/maximum dimming value
The upper and lower limits of the output value of all lighting
channels can be set with both the <minimum dimming value>
and <maximum dimming value> parameters.
Value range (with SendoPro, theSenda B/App)
Minimum dimming value 1 % - 25 %
Maximum dimming value 50 % - 100 %
Switch-off brightness
In the constant light control function, it is possible to choose
to switch the lighting off when there is sufcient brightness. If
the lighting is controlled down to the lower limit, the ligh-
ting will be switched off after the time set at the parameter
<Switch-off brightness>. With the selection “never off”, the
lighting will never be switched off. This behaviour is valid, as
long as people are present.
Value range (with SendoPro, theSenda B/App)
Switches lighting off after a set amount of time. 5 min – 9 h
Lighting is never switched off. never off
Manual dimming response
With constant lighting control, the manual dimming res-
ponse can be selected with the <manual dimming response>
parameter.
Value range (with SendoPro, theSenda B/App)
Constant light control remains active temporarily after manual
dimming to the current brightness value as the new setpoint
value. After the lighting time delay has expired, the originally
congured setpoint value is restored.
ofce
Constant light control is interrupted temporarily via manual dim-
ming. The set point value remains unchanged.
school
Further information can be found in the chapter “Lighting
channel C1, C2, C3 – constant lighting control” on page 2.
Standby time/standby dimming value
When standby time is activated, the lighting is not switched
off after completion of the lighting time delay, but remains set
to the standby dimming value as an orientation light.
Value range (with SendoPro, theSenda B/App)
Standby time 30 s – 60 min
Standby function (orientation light) is not active 0 s
Standby function (orientation light) is permanently
switched on
on
Standby dimming value 1 – 25 %
IR group address C1, C2, C3
This parameter is applied when using the “theSenda S” user
remote control.
A group address can be assigned to each lighting channel.
The “SendoPro, theSenda B/App” management remote con-
trol or the “theSenda S” user remote control can be used to
program the group addresses in the detector.
Group address value range
Adjustable values “SendoPro, theSenda B/App” I, II, III, All
Adjustable values “theSenda S” I, II
Using the “theSenda S” user remote control, the group
addresses can be assigned as follows:
For IR group address C1:
Press the and buttons simultaneously for at
least 5 s
I
Press the and buttons simultaneously for at
least 5 s
II
For IR group address C2:
Press the and
2
buttons simultaneously for at
least 5 s
I
Press the and
2
buttons simultaneously for at
least 5 s
II
Scene 1 C1, C2, C3 /Scene 2 C1, C2, C3
The desired dimming value for each lighting group can be
allocated to scene 1 and scene 2.

9
Value range (with SendoPro, theSenda B/App)
Adjustable values 0 – 100 %
Using the “theSenda S” user remote control, the lighting is
rstly set to a desired brightness and then saved as followed:
Press the button for at least 3 s. Scene 1 is saved
Press the button for at least 3 s. Scene 2 is saved
The scene is called up by briey pressing the button.
Conguration button/RC
The teach-in function and the conguration of lighting groups
via the button or the user remote control „theSenda S“ can
be enabled or disabled with the <conguration button/RC>
parameter.
Value range (with SendoPro, theSenda B/App)
Teach-in function and conguration via the button can be
executed.
enabled
The teach-in function and conguration via the button or the
user remote control "theSenda S" is disabled.
disabled
LED display motion
The motion detection can be displayed via the LED.
Value range (with SendoPro, theSenda B/App)
No display of motion detection. Off
The LED is switched on when motion is detected, otherwise it
remains off.
On
Control commands via remote control
The following control commands can be triggered with the
remote control:
Control command Description Can be
triggered
SendoPro,
theSenda
B/App
Can be
triggered
theSenda
P
DALI
conguration
Conguration of the lighting
groups
Group assignment
(Unaddressed)
Conguration of the
unaddressed lighting groups x
Group assignment
(All)
Conguration of all lighting
groups x
Change group
assignment
Change conguration of the
lighting groups x
End group
assignment
End conguration of the
lighting groups x
Reset DALI ECGs All connected DALI ECGs are
reset to factory settings x
Reset DALI relay The connected DALI relay is
reset to the factory setting. x
Switching light C1 Lighting group C1 can be
switched on and off. x x
Switching light C2 Lighting group C2 can be
switched on and off. x x
Switching light C3 Lighting group C3 can be
switched on and off x
Switching light
(All)
All lighting groups can be
switched on and off together x
Control command Description Can be
triggered
SendoPro,
theSenda
B/App
Can be
triggered
theSenda
P
Teach-in channel
C1
Lighting channel C1
execution x x
Teach-in channel
C2
Lighting channel C2
execution x x
Teach-in channel
C3
Lighting channel C3
execution x
Teach-in channel
C1 + C2 + C3
Activate for all lighting chan-
nels C1 - C3 x
Presence test On/Off x x
Light test On/Off x
Restart Restart detector x x
Factory settings
Set all parameters and
settings to factory setting;
DALI conguration remains
unchanged.
x
Teach-in channel C1, C2, C3
During teach-in, the currently measured brightness value is
accepted as the brightness setpoint value. Values outside the
permitted range will automatically be set to the appropriate
limit value.
You can use the „SendoPro, theSenda B/App“ management
remote control to execute all teach-in control commands.
With the “theSenda P” installation remote control, the fol-
lowing teach-in control commands are available.
Teach-in channel C1 Press the button and then the button
within 10 s
Teach-in channel C2 Press the
2
button and then the button
within 10 s
Teach-in channel C1
+ C2 Press the button
Presence test
Presence test mode is used to test presence detection and
wiring. Presence test mode can be activated with the “Sen-
doPro, theSenda B/App” management remote control or with
the “theSenda P” installation remote control ( button). The
detector goes directly into test mode when the test mode is
set:•Every movement is indicated by the LED.
•When motion is detected, the lighting is switched on.
•Constant light control is deactivated (switching mode).
•Teach-in cannot be activated in test mode.
•The lighting is switched off after 10 seconds when the
room is unoccupied.
•Brightness measurement is deactivated, detector does
not respond to brightness.
•Standby function is deactivated.
•The detector reacts as in conguration type “fully auto-
matic device”, even if “semi-automatic” is set.
•Test mode ends automatically after 10 min. The detector
restarts itself (see switch-on behaviour on page 11).
Light test
The light test mode is used to check the brightness threshold
and the constant light control. The light test mode can be

10
activated with the “SendoPro, theSenda B/App” management
remote control. The detector goes directly into test mode
when the test mode is set:
•The LED shows the light test mode (5 seconds on, 0.3
seconds off).
•The presence detector responds exactly as in normal
operating mode, only the reaction to brightness/dark-
ness is faster.
•In order to simulate this behaviour, either the area below
the presence detector can be illuminated or the blinds
operated.
•Test mode ends automatically after 10 min.
The detector restarts itself (see switch-on behaviour on
page 12).
LNote: Do not use a torch to switch on the presence
detector! The adaptive light switching thresholds will be
distorted!
Factory settings
The presence detector is supplied with the following parame-
ter values:
Parameter Value
Function C1/C2 Control
Function C3 Control
Light measurement source C3 centre
Terminal S1 assignment C1
Terminal S2 assignment C2
Terminal S3/P assignment Parallel
Brightness set point value C1, C2, C3 500 lux
Room correction factor Win, Mid, Inn, Int 0.3
Detection sensitivity (PIR) Increment 3
Lighting time delay 10 min
Short presence On
Energy saving mode eco
Presence switch-on delay 0 s
Presence time delay 10 min
Switch-on dimming value C1, C2, C3 50 %
Conguration type C1/C2, C3 auto
Control speed Standard
Minimum dimming value 10 %
Maximum dimming value 100 %
Switching off brightness 10 min
Response after dimming school
Standby time 0 s
Standby dimming value 10 %
IR group address C1 I
IR group address C2 II
IR group address C3 III
Scene 1 C1, C2, C3 30 %
Scene 2 C1, C2, C3 70 %
Conguration button/RC enabled
LED display motion off
The parameters can only be set to factory settings by using
the “SendoPro, theSenda B/App” management remote
control.
Reset DALI ECGs
The connected DALI ECGs are reset to factory settings and the
group addresses are deleted.
9. Start-up
Initial operation (system not congured)
After rst switching on the system power supply, the detector
is restarted, automatically identies all connected DALI lamps,
assigns short addresses and manages them in a list. This
stage is indicated by an LED ashing pattern (5 x on briey
every 3 s) and, depending on the size of the system, can last
up to 3 min.
If no DALI ECG is connected to the detector or a DALI line is
interrupted, the detector shows this with the LED ashing
pattern (LED is on and ashes off briey twice every 3 s).
If the system is OK, the detector automatically enters con-
guration mode and waits for conguration of the lighting
groups. This is indicated by the LED ashing pattern (2 x on
briey every 3 s). If conguration has not been carried out the
system will be in the following operating mode:
•Detector is in broadcast mode.
•Function is switching mode (only presence detection, no
light measurement).
•All lights are controlled with 100% switching/dimming
value.
•The operating mode is as a fully automatic device.
•All connected buttons are active. It is possible to switch
on and off, as well as dim.
•Time delay 10 min.
Configuration of the lighting groups
For the conguration, several options are available:
•Using the service remote control „theSenda B/App“
•Using the management remote control „SendoPro 868-A“
•Using the buttons or „theSenda S“ user remote control
Configuring the lighting groups with the theSenda B/app ser-
vice remote control
Connect the theSenda B with the corresponding „theSenda
Plug“ app.
Place the theSenda B under the detector (direct the remote
control towards the detector).
Select „theRonda P360-330 DALI“ as the type in the „the-
Senda Plug“ app.
In the „DALI conguration“ menu, select the required group
assignment.
For the DALI conguration, there are 3 options available:
y „Group assignment (unaddress.)“: only DALI EBs without a
group address are processed.
y „Group assignment (all)“: all connected DALI EBs are con-
gured. WARNING: All existing group assignments with group
number 1, 2 or 3 will be deleted.
y „Change group assignment“: the next existing EB is
searched for and selected.
LThe remote control must be directed to the detector! The
LED is switched off.
▻ After selecting the required group assignment, the
detector is in the programming mode.
▻ A DALI light starts to pulse (random order).
Use the button # to assign the required C1, C2 or C3 chan-
nel to the DALI EB.
▻The lamp conrms the assignment by dimming to 20 %.

11
▻ The next DALI light starts to pulse. One after the other,
the lighting groups are assigned to all the lights.
•In the case of group assignment (Unaddress) or (All):
When all DALI-ECGs have an assigned lighting group, the
detector automatically ends conguration and restarts
itself, see section „Switching behaviour“. Finally, the-
Ronda DALI enters normal operation and conguration is
complete.
•If necessary, the conguration process can be ended by
pressing „End Group Assignment“ (left function button).
In this case, the system is not ready for operation.
•If „Change group assignment“ has been selected, use the
„Next“ button (button below) to switch to the next DALI
EB without changing the lighting group. Otherwise, the
sequence remains the same. When all desired changes
have been made, the conguration can be completed by
pressing „End“ (button below).
Configuration of the lighting groups by management remote
control „SendoPro 868-A“
On the management remote control „SendoPro 868-A“,
select type „theRonda P360-330 DALI“.
Select „Menu“ (right-hand function button) and then „Con-
trol commands“ (left-hand function button).
Open „DALI conguration“ with „Open“ (right-hand function
button).
For the DALI conguration, there are 3 options available:
y „Group assignment (unaddressed)“: Only DALI ECGs without
a group address are processed.
y „Group assignment (All)“: All connected DALI ECGs are
congured. WARNING: All existing group assignments with
group number 1, 2 or 3 will be deleted.
y „Change group assignment“: The next available ECG will be
searched for and selected.
Select the desired group assignment using the off or on
button and start conguration by pressing „Send“ (right-
hand function button).
LThe remote control must be pointing at the detector! The
LED is switched off.
▻ A DALI lamp starts to pulse (random order).
Select the desired channel C1, C2 or C3 and assign to the
DALI ECG by pressing „Send“ (right-hand function button).
▻ The lamp conrms the assignment by dimming to 20
%.
▻ The next DALI lamp starts to pulse. In this way, all of the
lights are assigned to the lighting groups successively.
•In the case of group assignment (Unadressed) or (All):
When all DALI-ECGs have an assigned lighting group, the
detector automatically ends conguration and restarts
itself, see section „Switching behaviour“. Finally, the-
Ronda DALI enters normal operation and conguration is
complete.
•If so required, the conguration can be completed by
pressing „End“ (left-hand function button). In this case,
the system will not be ready for use.
•If „Change group assignment“ is selected, the right arrow
button „>“ can be used to switch to the next DALI ECG
without changing the lighting group. Otherwise, the
sequence remains the same. When all desired changes
have been made, the conguration can be completed by
pressing „End“ (left-hand function button).
Right-hand function button
Right button
Up button
Down button
Left-hand function button
Configuration of the lighting groups using buttons
For the conguration using buttons, the <Conguration
button/RC> parameter must be set to „enabled“. All connec-
ted buttons can be used for conguration.
LIf button S3 is used, the <Terminal S3/P assignment>
parameter may not be set to „Parallel“.
•DALI conguration is started by briey pressing any
button 5 x (<0.4 s) followed by 1 x long press (> 15 s).
The LED is switched off.
▻ A DALI lamp starts to pulse (random order).
•The lighting group is assigned by pressing the corres-
ponding button:
y 1 x short button push = Channel C1
y 2 x short button push = Channel C2
y 3 x short button push = Channel C3
▻ The lamp conrms the assignment by dimming to 20 %
(3 s after the last button push).
▻ The next DALI lamp starts to pulse. In this way, all of the
lights are assigned to the lighting groups successively.
•When all DALI-ECGs have an assigned lighting group, the
detector automatically ends conguration and restarts
itself, see section „Switching behaviour“. Finally, the-
Ronda DALI enters normal operation and conguration is
complete.
•If so required the conguration can be ended by pressing
any button for longer than 15 s. The detector restarts
itself. In this case, the system will not be ready for use
and must be recongured.
LInstead of the button, conguration can also be carried out
using the On/Off buttons on the „theSenda S“ user remote
control.
Checking the configuration
The lighting group assignment can be checked at any time
using the buttons or the „SendoPro, theSenda B/App“
management remote control, in that the individual lighting
groups are switched on or off (select the menu „control com-
mands“ on the „SendoPro, theSenda B/App“).
If the lighting group needs to be changed on individual DALI
ECGs, DALI conguration can be carried out using the „Sen-
doPro, theSenda B/App“ via „Change group assignment“.
When using the button, the whole DALI conguration must be
carried out again.

12
LA video on conguration of the lighting groups is available
at: https://www.youtube.com/user/TheThebenAG
Switch-on behaviour (congured systems)
Every time the power supply is switched on, the presence
detector runs through two phases that are indicated by the
LED:
1. Start-up phase (30 s)
•The red LED ashes at one second intervals and lighting
is switched on with switch-on dimming value.
•The detector does not respond to push-button com-
mands or to the “theSenda S” user remote control.
•The lighting is switched off after 30 s when the room is
unoccupied.
2. Operation
•The red LED is off. The constant light control or switching
mode are started.
•The detector is ready for operation.
10. Technical data
Operating voltage 110 – 230 V AC, +10% / -15%
Frequency 50 – 60 Hz
Upstream protection device: 16 A
Power consumption (without DALI-ECG) < 0.4 W
Type of installation Ceiling installation; ush/surface
mounted or ceiling installation
Recommended installation height 2.0 – 3.5 m/max. 15 m
Minimum height > 1.7 m
Detection area horizontal 360°
Maximum range Ø 7 m (Mh. 3.5 m) / 38 m2seated
Ø 25 m (Mh. 10 m) / 491 m2
walking
Setting range brightness setpoint value 10 – 3000 lux
Lighting time delay 10 s – 60 min
Presence switch-on delay 0 s – 30 min
Presence time delay 10 s – 120 min
Lighting standby time 0 s – 60 min /permanently on
Standby dimming value 1 – 25 %
Control output lighting 100 mA guaranteed, max. 250 mA,
max. 64 DALI operating devices,
basic insulation
Connection type Screw terminals
Max. cable cross-section Max. 2 x 2.5 mm²
Size of ush-mounted box Size 1, Ø 55 mm (NIS, PMI)
Protection rating IP 20 (IP 54 installed)
Ambient temperature -15 °C ... 50 °C
CE Declaration of Conformity This device conforms to the
safety regulations of the EMC
directive 2014/30/EU and of
directive 2014/35/EU.
Dali conformity IEC 62386-101, IEC 62386-103
Product overview
Type of
installation
Channel Operating
voltage
Colour Type Item
number
Ceiling
installation
Light 230 V AC White theRonda P360-
330 DALI WH
2080045
Troubleshooting
Fault Cause
Light does not switch
on and/or off if pre-
sence is detected and
in darkness
Brightness setpoint value is set too low; detector
set on semi-automatic; light was switched off
manually via button or “theSenda S”; person not
within detection area; obstruction(s) interrupting
detection; time delay set too short
Light stays on with
detection of presence
despite sufcient
brightness
Brightness setpoint value is set too high; light was
briey switched on manually via button or with
“theSenda S” (wait 30 min in switching operation);
detector is in test mode
Light does not switch
off and/or light swit-
ches on spontaneously
when no one is present
Wait for time delay (self-learning);
thermal sources of interference in the detection
area: fan heaters, incandescent lamps/halogen
spotlights, moving objects (e.g. curtains hanging in
open windows)
Push button does not
work
Device still in the start-up phase; illuminated
button was used without neutral conductor;
Push button not fed to the master. <Terminal S3/P
assignment> parameter set to "Parallel".
Light cannot be swit-
ched off with the push
button
Push button not fed to the detector. Check wiring
to the push button. <Terminal S3/P assignment>
parameter set to "Parallel".
Lighting does not react Short circuit or interruption in the DALI bus. Electri-
cal surge in the DALI bus: Disconnect the detector
from the supply network for 1 minute (thermal
fuse).
Error ashing
(4 x per second)
Error in self-test;
device not properly functional!
LED is on and ashes
off briey 2 x every 3 s
Detector does not recognise DALI ECGs. Check DALI
connections. At least 1 DALI ECG must be connec-
ted to the detector. Short circuit in DALI bus.
Master/Slave, Master/
Master parallel swit-
ching is not working
Detectors and buttons are not connected to the
same external conductor. <Terminal S3/P assign-
ment> parameter is not set to "Parallel".
11. Dimensions diagrams
86
46 25
40

13
12. Accessories
Back box 110A WH
Item No.: 9070912
Details > www.theben.de/en
Back box 110A GR
Item No.: 9070913
Details > www.theben.de/en
DE (ceiling installation) box 73A
Item No.: 9070917
Details > www.theben.de/en
Cover clip for area restriction
Item No.: 9070921
Details > www.theben.de/en
theSenda P
Item No.: 9070910
Details > www.theben.de/en
theSenda S
Item No.: 9070911
Details > www.theben.de/en
theSenda B/App
Artikel-Nr.: 9070985
Details > www.theben.de/en
13. Contact
Theben AG
Hohenbergstraße 32
72401 Haigerloch
GERMANY
Tel.: [phone]
Fax: [phone]
Hotline
Tel.: [phone]
[email protected]
www.theben.de

14