Theben theRonda S360 KNX UP WH User manual

1
theRonda S360 KNX UP WH
2089520
theRonda S360 KNX AP WH
2089550
theRonda S360 KNX AP GR
2089551
theRonda S360 KNX FLAT DE WH
2089560
307337 02
Presence detector
EN
1. Product characteristics
•Passive infrared presence detector for ceiling installation
•Circular detection area 360°, up to Ø 9 m (64 m²)
•Restriction of detection area with cover clips (type UP)
•Automatic presence- and brightness-dependent control
for lighting and HVAC
•Mixed light measurement suitable for uorescent (FL/
PL/ESL), halogen/incandescent lamps and LEDs
•2 light channels C1, C2
•Switching operation or constant light control with
standby function (orientation light)
•Switching mode with dimmable lighting
•Choice of fully or semi-automatic
•Brightness switching value or set point value can be
set in lux by using parameters, the object or via remote
control
•Teach-in of the brightness switching value or the set
point value
•Reduction of time delay when present briey (short-term
presence)
•Manual override by telegram or remote control
•2 presence channels C4, C5, individually congurable
•Switch-on delay and time delay congurable
•Setting the room correction factor for brightness measu-
rement comparison
•Adjustable sensitivity
•Test mode for checking function and detection area
•Scenes
•Parallel switching of multiple presence detectors
(Master/Slave or Master/Master)
•Protection class IP 54 when installed
•Installation in false ceilings with springs (type FLAT DE)
•Ceiling installation - surface mounted (type AP)
•User remote control «theSenda S» (option)
•Installation remote control «theSenda P» (option)
•Management remote control «SendoPro 868-A» (no
longer available)
•App remote control «theSenda B» (option) and corres-
ponding app «theSenda Plug» (iOS/Android)
•Accessories:
theSenda B (9070985), theSenda P (9070910), theSenda
S (9070911)
theRonda S360 KNX UP: surface frame 110A WH
(9070912), surface frame 110A GR (9070913), cover 110
GR (9070591), ceiling installation box 68A (9070992),
masking clips (9070921), QuickSafe safety cover
(9070531)
2. Safety
Danger of death through electric shock or fire!
¾ Installation should only be carried out by a
professional electrician!
WARNING
•Work on electrical systems may only be carried out by
electricians or by instructed persons under the guidance
and supervision of an electrician in accordance with the
technical regulations applying to electricity!
•Comply with the country-specic safety regulations for
work on electrical systems!
•The device is maintenance-free. If the device is opened
or penetrated with any object, the guarantee lapses.
3. Proper use
The presence detector is intended for interior installation. The
presence detector is exclusively intended for the use as con-
tractually agreed between the manufacturer and the user. Any
other use is considered to be unacceptable. The manufacturer
does not accept liability for any resulting damages.
4. Function
The presence detector is primarily used in ofces, corridors,
storage rooms and toilets for easy and energy-efcient
control of lighting as well as HVAC. The lighting is accordingly
inuenced by switching or constant light control.
Function




Mixed light measurement
Presence detection
 Articial light
Incident daylight

2
Light channel C1, C2
The presence detector detects people present based on
smallest movements. 1 light sensor simultaneously measures
the brightness in the room and can thus smoothly control the
lighting or switch it on and off according to the daylight. The
light outputs can be dynamically faded up and down by the
integrator. The brightness switching value or set point value
can be set via parameters, object or the management remote
control.
Switching
The lighting switches on with presence and insufcient
brightness, and off with absence or sufcient brightness.
Manual switching or dimming can be performed with a push
button. Manual switching off, dimming and scenes stop the
control for the duration of the presence.
Constant light control
When constant light control is active, the brightness is held
constant at the brightness set point value. Control is started
fully automatically or manually via push button or remote
control. Manual switching off, dimming and scenes stop the
control for the duration of the presence.
Time delay
The minimum time delay can be set for all light channels
in the range of 30 seconds to 60 minutes. If someone goes
into an unoccupied room only briey and leaves it within 30
seconds, then the light shuts off prematurely after 2 minutes
(short-term presence).
Standby
The standby function acts as an orientation light. After the
time delay expires, the lighting is set to the standby dim-
ming value (1 - 25 %). The standby time can be set between
30 s and 60 min or permanently. The lighting switches off
if the brightness level in the room exceeds the brightness
switching value/set point value. The lighting switches to the
standby dimming value automatically if the room brightness
falls below the brightness switching value/set point value.
The standby function can be activated or locked via an object.
In conjunction with a time switch, this allows energy-saving
solutions to be implemented.
Push button control
The lighting can be manually switched or dimmed at any time
via a push button. If the light is switched on manually, the
light will remain on during switching operation for at least
30 minutes provided people are present. It then switches off
when there is enough brightness. The light is forced off after
a preset time delay if the room was (previously) vacated. If
articial lighting is switched off manually, the lighting remains
switched off as long as the room is occupied. The lighting
switches again automatically after the time delay has expired.
Fully or semi-automatic
Lighting control via the presence detector operates fully
automatically for increased comfort or semi-automatically for
greater energy savings. In «fully automatic» the lights switch
on and off automatically. In «semi-automatic», the lighting
must always be switched on manually. The lighting is swit-
ched off automatically.
Presence channel C4, C5
The presence channels are typically used for HVAC control.
According to the selection, a telegram will only be sent due
to presence, completely independently of the brightness and
after expiry of the switch-on delay. The time delay will be
restarted at every movement. The presence channel is not
inuenced by push buttons.
Switch-on delay
The switch-on delay prevents instantaneous switching on.
The telegram is sent only on expiry of the switch-on delay,
provided that people are present at this time.
Time delay
The time delay enables delayed switching off of HVAC devices
and systems after the room is vacated.
If selected, a telegram can be sent after the expiry of the
presence time delay (once or cyclical).
5. Detection area
The circular detection area of theRonda presence detector
covers a middle detection area and permits a good room
coverage with many applications. Note that seated and
moving persons can be detected in differently-sized areas.
The recommended installation height is 2.0 m – 3.0 m. As
installation height increases, the sensitivity of the presence
detector decreases. Walking motions are necessary from ins-
tallation heights of 3.5 m, and the detection areas of several
detectors should overlap in the marginal zones. The detection
range is reduced as the temperature increases. As installa-
tion height increases, the sensitivity of the presence detector
decreases. The extent and distance between the active and
passive zones of the presence detector also increases.
Seated persons:
The details relate to smallest movements at table height
(approx. 0.8 m).
t
r / s
S
A

3
Instal-
lation
height (A)
oving persons Frontal
(r)
moving persons
Across (t)
seated persons (s)
2,0 m 38 m2Ø 7 m 5 m2Ø 2,5 m 5 m2Ø 2,5 m
2,5 m 38 m2Ø 7 m 7 m2Ø 3,0 m 7 m2Ø 3,0 m
3,0 m 50 m2Ø 8 m 13 m2Ø 4,0 m 13 m2Ø 4,0 m
3,5 m 50 m2Ø 8 m 13 m2Ø 4,0 m – –
4,0 m 64 m2Ø 9 m 13 m2Ø 4,0 m – –
All gures are guidance values.
Brightness measurement
The presence detector measures articial light and daylight
that is reected below the detector (opening angle of approx.
120°). The installation location is the reference point for the
lighting level. If the brightness measurement is deactivated,
the light channel only switches depending on the presence.
Switching
Direct light inuences the light measurement. The placement
of the oor lamps or suspended lighting directly below the
detector is to be avoided.
Constant light control
The detector must be positioned in such a way that it only
detects articial light that it controls itself. Articial light that
is controlled by other detectors, or manually switched work
lighting, inuence the brightness measurement of the detec-
tor. Direct articial light on the detector must be avoided.
Suitable lamps
The presence detector is designed for the operation of uore-
scent, compact uorescent, halogen and incandescent lamps
as well as LEDs.
6. Installation
The detector requires a clear line of sight to people. The in-
stallation height must not be less than 1.7 m and should not
exceed 4 m.
Flush-mounted tting (theRonda S360 KNX UP)
The presence detector is ush-mounted using a size 1 stan-
dard ush-mounting installation socket.
Ceiling installation (theRonda S360 KNX UP)
A ceiling installation unit 68A is available for simplied ceiling
installation of the presence detector (see accessories). This
also ensures cord grip and contact protection. The installation
diameter is 67,5 mm (drill diameter 68 mm).
9070992
Surface-mounted installation (theRonda S360
KNX UP)
A surface frame 110A is available for surface mounted instal-
lation (see accessories).
9070912

4
Ceiling Installation (theRonda S360 KNX FLAT DE)
Installation in false ceilings for ceiling thicknesses of 0.5 mm
to 3 cm. The diameter of the ceiling cutout must be between
62 mm and 70 mm.
Protection rating IP 54 is only met at the front (side of the
lens) and requires a smooth ceiling surface.
Ceiling installation - surface mounted (theRonda
S360 KNX AP)
b
a
c
d
20°
open
Turn the sensor unit (a) by about 20° counterclockwise, up to
te snap-in point. Remove the sensor unit. Break out the requi-
red cable passages (b). Mount the surface-mounted housing
(c) via the provided fastening holes to the ceiling. Perform the
wiring (d). Put on the sensor unit (a).
If a higher protection rating than IP 20 is required, the en-
closed seals have to be used in case of ceiling installation (c).
7. Start-up
1. Settings
All settings are made via ETS. See document «KNX manual
theRonda» (application description). The «theSenda P»
remote control or the «theSenda B» app remote control (with
«theSenda Plug» app) are optionally available for start-up
support. The «SendoPro 868-A» can be also used, but is no
longer available. Parameters can only be adjusted with the
«theSenda P». In this sense, the remote controls serve as
set-up aids. A range of alterable parameters is available for
adjustment with the remote control (see chapter «Parameters
via remote control»).
The response during operation can be changed via the remote
control‘s control commands.
2. Programming mode
The programming mode can be activated using the program-
ming button on the back of the presence detector or, without
dismounting the presence detector, via the «SendoPro 868-A»
management remote control, «theSenda P» installation
remote control, or «theSenda B» app remote control (with
«theSenda Plug» app).
theRonda S360 KNX UP



Programming mode button
Mechanical safety lock
theRonda S360 KNX DE

Programming mode button
theRonda S360 KNX AP

Programming mode button

5
3. Setting the device to the factory setting
The presence detector is supplied with a factory setting. This
factory setting can be restored.
Activation Description
Powerup Hold down the programming button while
switching on bus voltage.
4. Operation mode
The theRonda S360 KNX knows 3 operating modes
•Normal • test-presence •test-light
5. Switching behaviour
After the bus voltage is switched on or the parameters are
downloaded via the ETS, the detector rst runs through the
start-up phase of 30 s, then it changes into normal operation.
An LED displays the current status.
1. Start-up phase (30 s)
•The LED ashes in one second intervals.
•Switching: Light outputs send an ON telegram regardless
of brightness
•Constant light control: control inactive, the lighting will
be dimmed up to the maximum (value telegram max.
control value).
•When no one is present or there is sufcient brightness,
an OFF telegram is sent after 30 s (light off).
2. Operation mode normal
•The detector is ready for operation (LED off).
3. In the event of malfunction
•LED ashes rapidly
•For troubleshooting, see chapter «Troubleshooting»
8. Parameters via remote control
The following parameters can be queried or changed via
the remote control for support during installation as well as
servicing:
Parameter Description Can be
queried by
Sendo-
Pro/the-
Senda B
(app)
Can be
changed
by Sendo-
Pro/the-
Senda B
(app)
Can be
changed
theSenda P
Brightness set
point value C1
Value range
in lux
x x x
Alternative
brightness set
point value C1
Value range
in lux
x x
Brightness
measurement
value C1
Lux meter
brightness
value in lux
x
Brightness
actual value C1
Measured
brightness
value in lux
x
Lighting time
delay
Value ranges
in seconds/
minutes
x x
Detection sensi-
tivity (PIR)
Value range in
levels
x x
With the «SendoPro 868-A» management remote control, as
well as with «theSenda B» app remote control (with «the-
Senda Plug» app), parameters can be queried by sending
values level-by-level to the detector. If the sent values are
below the set parameter, the LED illuminates briey. If the
sent values are equal or above the set parameter, the LED
ickers for 2 seconds.
This adjustment of parameters does not change the settings
in ETS.
Alterable parameters via remote control
1. Adjustment with the remote control
The parameters are sent to the presence detector via infrared
by using the «SendoPro 868-A» management remote control,
the «theSenda P» service remote control, or «theSenda B»
app remote control (with «theSenda Plug» app). Changed
parameters are immediately applied and used by the detector.
LED description
Flickering for 2 s
After sending the new parameter with remote control or
app, the presence detector indicates the correct reception by
ickering for 2 s.
Lighting up briefly
The parameter/command sent from the remote control was
rejected by the presence detector. The command is not valid.
Check the selected detector type and sent parameters with
management remote control or app remote control (app).
2. Brightness switching value/set point value channel C1
light
The brightness switching value/set point value denes
the minimum desired brightness. The currently prevailing
brightness is measured below the presence detector. If the
prevailing brightness is below the switching value/set point
value, the light is switched on when a presence is detected (in
conguration type fully automatic).
Value range
Adjustable values "SendoPro 868-A"/"theSenda B" (app) 10–3000 lux
Adjustable values "theSenda P" 10, 15, 300,
500, 800 lux
Deactivation of brightness measurement (brightness
measurement has no effect)
The light channels only switch according to presence and
absence.
"SendoPro 868-A"/"theSenda B" (app) Measurement
off
"theSenda P" Button
3. Alternative brightness switching value/set point value
channel C1 light
The alternative brightness switching value/set point value
can be used to dene a second, different brightness swit-
ching/ set point value. For example, a day and night mode
with two different brightness levels can be set up in combi-
nation with the brightness switching value/set point value
channel C1 light. The alternative brightness switching value/
set point value is activated or switched via bus object.

6
Value range
cf. 2. Brightness switching value/set point value channel C1
light
4. Brightness measurement value C1
The brightness measurement value at the ceiling is inuenced
by the installation location, incidence of light, position of the
sun, weather conditions, the reection properties of the room,
and the furniture. In order to be able to adhere to the requi-
red lux value in the desired area, a comparison of the bright-
ness measurements as necessary.
When sending the brightness measurement value, the room
correction factor of the corresponding lighting channel is
automatically adjusted to the conditions inside the room.
The measured lux value below the presence detector is
sent to the detector by the remote control. Two different pro-
cedures can be selected for the comparison.

Room correction factor=
Brightness value at the ceiling
Brightness value on the work
surface
LPlease note the instructions in the «KNX theRonda»
manual concerning the calibration of light measurements
or setting the room correction factor.
Using management „SendoPro 868-A“ remote control and lux
meter:
Dim all lights to maximum power. If possible, move down
the blinds.
▻The lux meter is placed on the work surface below the
sensor and the measured lux value is entered via the
management remote control «SendoPro 868-A», para-
meter <brightness measurement value C1>.
▻The room correction factor will be calculated automati-
cally. Values between 0.05 and 2.0 are permitted. Calcu-
lated or entered values outside the permitted range will
automatically be set to the appropriate limit value.
▻The calculated room correction factor will be applied.
Using „theSenda B“ remote control and „theSenda Plug“ app:
Connect «theSenda B» remote control with the correspon-
ding «theSenda Plug» app.
Select the appropriate detector type and load the parame-
ter set.
Select <Brightness measurement value C1> parameter.
Using theSenda B remote control
Set up theSenda B according to the drawing, and move
away a few steps from the measurement location, so the
lux measurement will not be inuenced.
Press OK.
▻A new window with the measured brightness measu-
rement value is shown. If you would like to apply this
value,
press OK.
Important: Press the send button ( ). After this, the
brightness measurement is harmonised.
Using lux meter
Set up or align the lux meter according to the drawing, and
read the lux value.
Press «Enter» in the app.
▻A new window opens.
And the lux value and press OK.
▻Brightness measurement value appears in the display.
Important: Press the send button ( ). After this, the
brightness measurement is harmonised.
▻The room correction factor will be calculated automati-
cally. Values between 0.05 and 2.0 are permitted. Calcu-
lated or entered values outside the permitted range will
automatically be set to the appropriate limit value.
▻The calculated room correction factor will be applied.
For monitoring purposes, the room correction factor can be
queried via object 8.
The room correction factor can be changed directly only
via the ETS. The standard value is 0.3 and is suitable for
most applications. Changes are only sensible in sharply
varying situations.
5. Lighting time delay
Value range
Adjustable values "SendoPro 868-A"/"theSenda B"
(app) 30 s - 60 min
Adjustable values "theSenda P"
30 s, 60 s, 2 min,
10 min, 20 min,
60 min
6. Detection sensitivity
The detector has 5 sensitivity increments. The basic setting
is the middle increment (3). With the «SendoPro 868-A»
management remote control, as well as with «theSenda B»
app remote control (with «theSenda Plug» app), the incre-
ments 1 to 5 can be selected and sent to the detector. With
the «theSenda P» installation remote control, the sensitivity
can be decreased or increased by one increment
each time the button is pushed.
Increment Sensitivity
1 very insensitive
2 insensitive
3Standard
4 sensitive
5 very sensitive
By selecting the test presence operating mode, the set sensi-
tivity increment is not changed.

7
Control commands
The following control commands can be triggered with the
remote control:
Control
command
Description Can be trigge-
red by Sendo-
Pro / theSenda
B (app)
Can be trigge-
red theSenda
P
Programming
mode
Activation of pro-
gramming mode
x x
Teach-in chan-
nel C1
x x
Master/Slave
query
Master/Slave x
Switching light All lighting groups
can be switched on
and off.
x x
Presence test On/Off x x
Test light On/Off x
Restart Restart detector x x
Teach-in
The currently measured brightness value will be accepted
as the brightness set point value. Transfer is made to the
currently active brightness setpoint value. That is, if the alter-
native brightness set point value is switched to, the currently
measured brightness value [lux] is transferred to the alter-
native brightness set point value via the teach-in command.
Values outside the permitted range will automatically be set
to the appropriate limit value.
Test mode
The theRonda S360 KNX has two test modes.
•Presence test
•Light test
1. Presence test
The presence test is used for checking the detection area and
the parallel switching.
Activation Presence test control command "On" with "SendoPro
868-A" management remote control or with "theSenda B"
app remote control (with "theSenda Plug" app). On "the-
Senda P" installation remote control with the button..
ON telegram via bus object (51).
The presence test can be activated anytime.
End With subsequent restart:
Presence test control command "Off" with "SendoPro
868-A" management remote control or with "theSenda
B" app remote control (with "theSenda Plug" app). On
"theSenda P" installation remote control with the button
(reset).
OFF telegram via bus object (51)
Mains failure and thus power up
Automatically according to the time set in the ETS
Without restart:
Activation of light test with "SendoPro 868-A" management
remote control or with "theSenda B" app remote control
(with "theSenda Plug" app).
Indication of
LED status
channels
Description
On When movement occurs, the LED goes on and channels C1,
C2 switch on.
Off After the movement stops, the LED is off and the channels
C1, C2 switch after approx. 10 s.
Test response
•Deactivated brightness measurement, light output does
not react to brightness
•The detector reacts as in conguration type fully auto-
matic, even if semi-automatic is set.
•The control type changes to switching if the control type
is set to constant light control. The light is not controlled.
•Light «On» during motion; light «Off» during absence
•Channels C1 and C2 light have a xed time delay of 10 s.
•The presence channels react unchanged as in normal
operation.
Commands and adjustable parameters
In the presence test, the following commands are possible
with «SendoPro 868-A» management remote control and
«theSenda B» app remote control (with «theSenda Plug»
app):
•Ending the presence test
•Activating the light test
•Changing detection sensitivity
The selected detection sensitivity (1 . . 5) is unchanged on
activation of the presence test. The sensitivity can be adjusted
during the test and will remain unchanged after completion
of the presence test. The presence detector performs a restart
after the end of the test mode.
2. Light test
The light test is used to check the brightness switching
value/set point value.
Activation Presence test control command "On" with "SendoPro
868-A" management remote control or with "theSenda B"
app remote control (with "theSenda Plug" app).
ON telegram via bus object (52)
The light test mode can be activated anytime.
End With subsequent restart:
Light test control command "Off" with "SendoPro 868-A"
management remote control or with "theSenda B" app
remote control (with "theSenda Plug" app). On "the-
Senda P" installation remote control with the button
(reset).
OFF telegram via bus object (52)
Mains failure and thus power up
Automatically according to the time set with the ETS
Without restart:
Activation of presence test with "SendoPro 868-A" manage-
ment remote control, "theSenda B" app remote control
(with "theSenda Plug" app), or "theSenda P" installation
remote control using the "test" button.
LED display Description
Flashing,
5 s On
0.3 s Off
The LED ashes as long as the light test is active.
Test response
The presence detector responds 100 % like in normal ope-
ration, only the reaction to bright/dark is faster. This makes
it possible to test the brightness threshold and the adaptive
response. The control is also faster. All selected functions and
parameters remain unchanged.
Commands and adjustable parameters
In the light test mode, the following commands are possible
with «SendoPro 868-A» management remote control and

8
«theSenda B» app remote control (with «theSenda Plug»
app):
•End light test
•Change brightness switching value/set point value chan-
nel C1 light
•Activate presence test
The presence detector performs a restart after the end of the
test mode.
Do not use a pocket lamp to switch the presence
detector. The presence detector will learn this and
thereby distort the adaptive light thresholds and
hysteresis values.
In order to simulate this behaviour, the area below the presence
detector should be illuminated or the blinds operated. Reactivate
the light test for a new test.
Troubleshooting
Fault Potential cause
Light does not switch
on or switches off if
presence is detected
and in darkness
Lux value is set too low; detector set on semi-
automatic; light was switched off manually via
push button or with remote control; person not
within detection range; obstruction(s) interrupt-
ing detection; time delay set too short.
Light stays on when
someone is present
despite sufcient
brightness
Lux value is set too high; light was recently swit-
ched on manually via push button or by remote
control (wait 30 min during switching operation);
detector is in test mode.
Light does not switch
off or light switches on
spontaneously when
no one is present
Wait for time delay (self-learning); thermal
sources of interference in the detection area: fan
heaters, incandescent lamps/halogen spotlights,
moving objects (e.g. curtains hanging in an open
window).
Error ashing
(3 x per second)
Error in self-test;
Invalid parameter values in the detector (see
KNX manual theRonda S360 KNX Chapter 2.4.2
Settings, parameter settings with download).
Device not properly functional!
LED display
LED Description
Flashing at
one second
intervals
The presence detector is in the start-up phase.
Flickering for
2 s
The command sent from the remote control via infrared
was accepted by the presence detector.
Lighting up
briey
The command sent from the remote control via infrared
was rejected by the presence detector. The command is
not valid. Check the selected detector type or parameters
on the SendoPro or in the app.
Error ashing
(3 x per
second)
Error ashing; The presence detector has found an error.
Flashing,
5 s On
0.3 s Off
The presence detector is in light test mode.
Lights up
or ickers
irregularly
The presence detector is in presence test mode or "LED
display movement" is activated. The LED indicates the
detection of movements.
Dimensions diagrams
theRonda S360 KNX UP
theRonda S360 KNX FLAT DE
theRonda S360 KNX AP

9
9. Technical data
Operating voltage Bus voltage KNX, max. 30 V
Power consumption max. 9 mA/13 mA with LED
Type of installation Ceiling installation
Recommended instal-
lation height
2.0 – 3.0 / max. 4.0 m (minimum height > 1.7 m)
Detection area
horizontal 360°
Maximum range Ø 4 m (Mh. 4 m) / 13 m2radially moving
Ø 9 m (Mh. 4 m) / 64 m2tangentially moving
Setting range of
brightness switching
value/set point value
approx. 10 – 3000 lux / measurement OFF
Lighting time delay 30 s – 60 min
Presence time delay 10 s – 120 min
Presence switch-on
delay
10 s – 30 min / inactive
Standby dimming
value
1 – 25 % of the lamp output
Standby time 30 s – 60 min / inactive / permanently on
All settings are remo-
tely congurable
see KNX manual
Connection type Plug-in terminals, type WAGO 243
Protection rating
(surface-mounted)
IP 54
Protection rating
(ush-mounted)
IP 20 (IP 54 installed)
Protection rating
(FLAT DE)
IP 20 (IP 54 installed)
Ambient temperature -15 °C ... +50 °C
CE Declaration of
Conformity
This device conforms to the safety regulations of
the EMC Directive 2014/30/EC.
RCM compliance This device is compliant with the ACMA
guidelines.
Product overview
Type of
installation
Channel Colour Type Item number
Ceiling
installation
2 Light |
2 HVAC
White theRonda S360
KNX UP WH
2089520
Ceiling
installation
2 Light |
2 HVAC
White theRonda S360
KNX AP WH
2089550
Ceiling
installation
2 Light |
2 HVAC
Grey theRonda S360
KNX AP GR
2089551
Ceiling
installation
2 Light |
2 HVAC
Special colour
in accordance
with customer
information
theRonda S360
KNX AP SF
2089553
Ceiling
installation
2 Light |
2 HVAC
White theRonda S360
KNX FLAT DE WH
2089560
10. Contact
Theben AG
Hohenbergstraße 32
72401 Haigerloch
GERMANY
Phone: [phone]
Fax: [phone]
Hotline
Phone: [phone]
[email protected]
www.theben.de