Theben theMova S360-101 DE WH User manual

1
theMova S360-101 DE WH
1030565
theMova S360-101 DE GR
1030566
theMova S360-101 AP WH
1030555
theMova S360-101 AP GR
1030556
307067
Motion detector
EN
1. Product characteristics
•Passive infra-red motion detector for ceiling installation
•Circular detection area 360°, up to Ø 9 m (64 m2)
•Automatic motion and brightness-dependent control for
lighting and HVAC
•Mixed light measurement suitable for uorescent lamps
(FL/PL/ESL), halogen/incandescent lamps and LEDs
•Channel A light: relay, 230 V
•Operation as fully automatic device
•Brightness switching value congurable, teach-in
function
•Pulse function for staircase light time switch
•Channel H, presence: relay, oating e.g. for HVAC control
•Time delay congurable
•Detection sensitivity congurable
•Ready for immediate use due to factory presetting
•Test mode for checking function and detection area
•Installation in false ceilings with springs, type DE
•Surface mount on ceiling, type AP
•User remote control „theSenda S“ (option)
•Management remote control „SendoPro“ (optional)
•Service remote control „theSendaP“ (option)
2. Safety
Danger of death through electric shock or fire!
Installation should only be carried out by a pro-
fessional electrician!
WARNING
•Work on electrical systems may only be carried out by
electricians or by instructed persons under the leader-
ship and supervision of an electrician in accordance with
the technical regulations applying to electricity!
•Comply with the country-specic safety regulations for
work on electrical systems! Ensure absence of voltage in
the cable before installation!
•The device is maintenance-free. If the device is opened
or penetrated with any objects the guarantee lapses.
3. Intended use
The motion detector is intended for interior installation. The
motion detector is exclusively intended for the use as con-
tractually agreed between the manufacturer and the user. Any
other use is considered to be unacceptable. The manufacturer
does not accept liability for any resulting damages.
4. Function
The motion detector is primarily used in passage ways such
as corridors, stairs, toilets, basements and garages as well
as in homes for easy and energy-efcient control of lighting
plus HVAC. The switch contact „light“ switches lighting on with
presence and insufcient brightness, and off with absence.
The „Presence“ switch contact controls heating, ventilation
and air conditioning systems. The contact closes when people
are present.
Functional description




Mixed light measurement
Motion detection
 Articial light
Incident daylight
Channel A light
Switching response is controlled by presence and brightness.
The switch contact for channel A light closes during darkness
and when someone is present. It opens with a delay once the
room is vacated after the set time delay.
Time delay
The time delay enables delayed switching off of lighting after
the room is vacated. The time delay is adjustable in a range of
10 s to 60 min.
Fully automatic
Lighting control of the motion detector operates fully auto-
matically for increased comfort. In „fully automatic“ the lights
switch on and off automatically.
Pulse function
Time delay can be set to pulse for controlling existing stair-
case light timer switch. To do so, the light output produces
every 10 seconds a pulse of 0.5 seconds duration if people
are present or it is dark.

2
Channel H presence
Channel H presence is used for HVAC control. The switching
response of the oating contact is inuenced only by pre-
sence and not by brightness. If the contact is closed, the time
delay will be restarted at every motion.
Time delay
The time delay enables delayed switching off of HVAC devices
and systems after the room is vacated. The time delay is
adjustable in a range of 10 s to 120 min.
5. Detection area
The circular detection area of theMova S motion detector
covers an average detection area. Note that moving persons
can be detected in differently-sized areas. The recommended
installation height is 2.0 m – 4.0 m. As installation height
increases, the sensitivity of the presence detector decrea-
ses. The extent and distance between the active and passive
zones of the motion detector also increases. The detection
range is reduced as temperatures increase.
Installation
height (A)
Moving persons
Frontal (r)
Moving persons
Across (t)
2.0 m 5 m2 Ø 2.5 m 38 m2 Ø 7 m
2.5 m 7 m2 Ø 3 m 38 m2 Ø 7 m
3.0 m 13 m2 Ø 4 m 50 m2 Ø 8 m
3.5 m 13 m2 Ø 4 m 50 m2 Ø 8 m
4.0 m 13 m2 Ø 4 m 64 m2 Ø 9 m
Brightness measurement
The motion detector measures articial light and daylight that
is reected below the detector (opening angle approx. 120°).
The installation site is a reference point for the lighting level.
The light measurement is switched off when the light relay
is switched on. If the brightness measurement is deactivated,
the channel A light only switches depending on the presence
(brightness switching value set to „measurement off“ via the
remote control).
Suitable lamps
The motion detector is designed for the operation of uore-
scent lamps, compact uorescent lamps, halogen/incande-
scent lamps and LEDs. The maximum number of switchable
lights is restricted due to the high inrush current levels of
the EBs and LED drivers. The use of an external contactor
helps with large loads. All switched loads must be properly
suppressed.
6. Installation
Ceiling installation
Installation in false ceilings for ceiling thicknesses of 0.5 mm
to 3 cm. The diameter of ceiling cutouts must be between 62
mm and 70 mm. The cable strain relief is with using a cable
tie (width: 3.5 – 4.8 mm).
The detector requires a clear line of sight to people. The
installation height must be no less 1.7 m and no higher than
4 m.
Surface mount on ceiling
20°
open
b
e
a
d
c
b
c

3
Rotate sensor assembly approx. 20° anticlockwise until it
clicks.
Detach sensor assembly.
Open knock-outs as needed to feed wires through.
Mount power assembly on ceiling via the xing holes.
Connect wiring according to markings on push-in termi-
nals; conductor cross-section 0.25 – 2.5 mm2 .
Attach sensor assembly (a), taking care to insert plug-in
connector (e)
7. Switching
The motion detectors can be operated as a master in indivi-
dual switching. With parallel connection of the light outputs
(L‘), it must be ensured that all detectors connected in parallel
are connected to the same phase.
Individual switching
In individual switching, the motion detector as master detects
presence and brightness and controls lighting.
AC / DC
H2
H1
L’
8. Settings
Motion detector theMova S does not have a potentiometer.
The motion detectors are supplied with basic settings ready
for operation. The specications are guidance values. The ser-
vice remote control „theSendaP“ or the management remote
control „SendoPro 868-A“are available as an option for start-
up. They enable remote setting of all required settings.
Parameters via remote control
The following parameters can be queried or changed via
the remote control for support during installation as well as
servicing:
Parameter Description Can be
queried
SendoPro
868-A
Can be
changed
SendoPro
868-A
Can be
changed
theSenda
P
Brightness
switching value
Channel A light
Value range in lux x x x
Measurement off x x
Brightness
actual value
channel A light
Value range in lux X
Parameter Description Can be
queried
SendoPro
868-A
Can be
changed
SendoPro
868-A
Can be
changed
theSenda
P
Lighting time
delay
Value ranges in
seconds and minutes x x
Pulse x x
Presence time
delay
Value ranges in
seconds and minutes x x
Detection sen-
sitivity (PIR) Value range in levels x x
Group address
channel A light All /I /II / III x
LED display
motion Off /On x
The parameters are sent to the motion detector with the
„SendoPro 868-A“ management remote control or with „the-
Senda P“ installation remote control via infra-red. Changed
parameters are immediately applied and used by the detector.
With the „SendoPro 868-A“ management remote control,
parameters can be queried by sending values level-by-level
to the detector. If the sent values are below the set parame-
ter, the LED illuminates briey. If the sent values are equal or
above the set parameter, the LED ickers for 2 seconds.
Control commands via remote control
Control command Description Can be
triggered
SendoPro
868-A
Can be
triggered
theSenda
P
Teach-in channel
A light
The currently measured
brightness value will be
accepted as the brightness
switching value. Values out-
side the permitted range will
automatically be set to the
appropriate limit value.
x x
Switch lights on/
off
Lighting group can be swit-
ched on and off. x x
Presence test On /Off x x
Restart Restart detector x x
Factory regulations Set all parameters and set-
tings to factory setting. x
Brightness switching value Channel A light
The brightness switching value denes the minimum desired
brightness. The current prevailing brightness is measured
below the motion detector. If the prevailing brightness is
below the switching value, the light switches on as soon as a
presence is detected.
Value range
Lux values with "SendoPro 868-A" management remote
control
The "theSenda P" installation remote control offers the
following values
(The currently measured brightness value (Lux) can
be adopted with the "SendoPro 868-A" management
remote control, with the teach-in control command or
with the "theSenda P" installation remote control via the
teach-in button.)
Values outside the permitted range will automatically be
set to the appropriate limit value.
30 - 3000 Lux
30, 300, 500,
800 lux

4
- Deactivating the brightness measurement (the bright-
ness has no inuence)
- Channel A lighting always switches with presence/
absence.
"SendoPro 868-A" Management remote control, "the-
Senda P" installation remote control
Measurement
off
Button
Time delay channel A light
Value range
Adjustable values with "SendoPro 868-A" manage-
ment remote control
In the "theSenda P" installation remote control, the
following values are available
10 s - 60 min
10 s, 30 s, 60 s, 2
min, 10 min, 20 min,
60 min
Control for staircase light timer switch
(0.5 s "on" / 10 s "off")
"SendoPro 868-A"
"theSenda P"
Pulse
Button 1
Time delay channel H Presence
The presence channel switches on the basis of the presence
(without brightness as a factor). The relay contact opens once
the room is vacated after the set time delay expires.
Value range
Adjustable values "SendoPro 868-A" 10 s ... 120 min.
Adjustable values "theSenda P" 10 s, 30 s, 60 s, 2
min, 10 min, 20 min,
120 min
Detection sensitivity
The detector has 5 sensitivity increments. The basic setting is
the middle level (3).
By selecting the operation mode test presence, the set sensi-
tivity increment is not changed.
With the „SendoPro 868-A“ management remote control,
levels 1 to 5 can be selected and sent to the detector.
With the „theSenda P“ installation remote control, the sen-
sitivity can be reduced or increased by one level with every
button press.
Level Sensitivity
1 very insensitive
2 insensitive
3 Standard
4 sensitive
5very sensitive
Group address channel A light
This parameter is applied when using the „theSenda P“ user
remote control.
A group address can be assigned to the channel A light.
The „SendoPro 868-A“ or „theSenda S“ can be used to pro-
gram the group addresses in the detector.
Group address value range
Adjustable values "SendoPro 868-A" I, II , III , All
Adjustable values "theSenda S" I, II
LED display motion
The motion detection can be displayed via the LED.
Value range
No display of motion detection. Off
The LED switches on when motion is detected, otherwise swit-
ches off.
On
Adjustment possible only with „SendoPro 868-A“.
Factory settings
The theMova P360-101 motion detector is supplied with the
following parameter values:
Parameter Value
Brightness switching value Channel A light 300 lux
Lighting time delay 10 min
Presence time delay 10 min
Detection sensitivity (PIR) Stage 3
Group address channel A light T
LED display motion Off
9. Start-up
Switching behaviour
Every time the power supply is switched on, the motion
detector rst runs through a start-up phase of 30 s, and then
switches to normal operation. A LED displays the current
status:
1. Start-up phase (30 seconds)
•The red LED ashes every second, both switch contacts
are closed (light and presence on).
•The detector does not react to remote control commands.
•When no one is present both contacts open after 30
seconds.
2. Operation
The detector is ready for operation (LED off).
Test detection area
The test mode detection area is used to test presence detec-
tion and wiring. Presence test mode can be activated with the
„SendoPro 868-A“ management remote control and with the
„theSenda P“ installation remote control.

5
Setting test mode detection area with remote control
•The detector goes directly into test mode when the test
mode is set via the remote control:
□Every movement is indicated by the LED.
□When movement occurs the light and presence switch
contacts close.
□When no one is present the light switch contact opens after
10 seconds.
□Brightness measurement deactivates, detector does not
react to brightness.
□Teach-in cannot be activated in test mode.
•Test mode ends automatically after 10 mins. The detector
performs a new start (see switch-on behaviour).
10. Technical data
Operating voltage 230 V AC +- 10 %
Frequency 50 Hz
Upstream protection device: 13 A
Power consumption approx. 0.5 W
Type of installation Ceiling installation
Recommended installation height 2.0 – 4.0 m
Minimum height > 1.7 m
Detection area horizontal
vertical
360°
120°
Maximum range Ø 4 m (Mh. 3 m) / 13 m2radially
moving
Ø 8 m (Mh. 3 m) / 50 m2tan-
gentially moving
Setting range brightness switching value 30 – 3000 Lux
Lighting time delay A light 10 s – 60 min / Pulse
Presence time delay 10 s – 120 min
Channel A light Relay 230 V /10 A, µ-contact
Max. switching capacity cos j1 resistive 2300 W
Max. switching capacity cos j 0.5 1150 VA
Max. switching capacity LED
Guide values
see manufacturer concerning
cos j
< 2 W : 25 W / > 2 W : 70 W
Guidance value max. inrush current level 400 A / 200 µs
Maximum number EBs T5/T8 10 x 54/58 W, 16 x 35/36 W
5 x 2 x 54/58 W
8x 2x 35/36 W
Channel H, presence Floating relay
Maximum voltage 220 V DC / 250 V AC
Maximum switching capacity 50 W / 50 VA (max. 2 A)
Recommended minimum load 0.5 mV / 10 mA
Connection type Screwless terminals
Max. cable cross-section max. 2.5 mm²
Protection rating: theMova S360-101 DE
Protection rating: theMova S360-101 AP
IP 20
IP 40 in installed state
IP 54
Ambient temperature -15 °C to +50 °C
CE Declaration of Conformity This device conforms to the
safety regulations of the EMC
directive 2004/108/EC and of
NSR 2006/95/EC.
Product overview
Type of
installation
Channel Operating
voltage
Colour Type Item No.
Ceiling
installation
Light |
HVAC
230 V AC White theMova
S360 -101
DE WH
1030565
Ceiling
installation
Light |
HVAC
230 V AC Grey theMova
S360 -101
DE GR
1030566
Ceiling
installation
Light |
HVAC
230 V AC Special colour
in accordance
with customer
information
theMova
S360 -101
DE SF
1030568
Ceiling
installation
Light |
HVAC
230 V AC White theMova
S360 -101
AP WH
1030555
Ceiling
installation
Light |
HVAC
230 V AC Grey theMova
S360 -101
AP GR
1030556
Ceiling
installation
Light |
HVAC
230 V AC Special colour
in accordance
with customer
information
theMova
S360 -101
AP SF
1030558
Troubleshooting
Fault Cause
Light does not switch
on if presence is
detected and in
darkness
Lux value is set too low; light was switched off
via theSenda S; person not within detection area;
obstruction(s) interrupting detection; time delay
set too short
Light does not switch
off and/or light
switches on spontane-
ously when no one is
present
Wait for time delay;
Thermal sources of interference in the detection
area: fan heaters, incandescent lamps/halogen
spotlights, moving objects (e.g. curtains hanging in
an open windows);
Load (EBs, relays) not cleared
Error ashing
(4 x per second)
Error in self-test;
Device not properly functional!
LED display
LED Description
Blinking in 1
second cycle
The motion detector is in the start-up phase.
Flickering
for 2 s
The command sent from the remote control via infrared was
accepted by the motion detector.
Lights up
briey
The command sent from the remote control via infrared
was rejected by the motion detector. The command is not
valid. Check the detector type or parameter selected in the
"SendoPro".
Fast
blinking
Error blinking; The motion detector has found an error.
Lights or
ickers
irregularly
The motion detector is in detection area test mode or "LED
display movement" is activated. The LED displays detection
of movement.
Guarantee
ThebenHTS motion detectors are manufactured with the
utmost care and using state-of-the-art technology and are
quality-tested. ThebenHTS AG therefore guarantees perfect
operation when used correctly. Should a fault occur, however,
ThebenHTS AG will full the guarantee within the scope of the
general terms and conditions.
Please note in particular:
•that the guarantee period lasts 24 months from the date
of manufacture.
•that the guarantee is invalidated if you, or a third party,
make changes or undertake repairs to the devices.

6
•that, insofar as the motion detectors are connected to
a software-controlled system, the guarantee for this
connection is only valid when the indicated interface
specication is complied with.
We undertake to repair or place as quickly as possible all
components of the delivered device that have become
defective or unusable through demonstrably poor material,
faulty construction or incomplete delivery up to the end of the
guarantee period.
Returns
In the event of a guarantee claim, please return the device to
the relevant dealer together with the delivery note and a brief
description of the fault.
Industrial property rights
The design as well as hardware and software of these devices
are protected by copyright.
Dimensional drawings
theMova S360-101 DE
theMova S360-101 AP
11. Accessories
SendoPro 868-A
Item No: 9070675
Details > www.theben.de
theSenda S
Item No: 9070911
Details > www.theben.de
theSenda P
Item No: 9070910
Details > www.theben.de
12. Contact
ThebenHTS AG
Im Langhag 7b
8307 Effretikon
SWITZERLAND
Phone [phone]
Fax [phone]
Hotline
Phone [phone]
[email protected]
Addresses, telephone numbers etc.
www.theben-hts.ch
All countries except Switzerland
Theben AG
Hohenbergstraße 32
72401 Haigerloch
GERMANY
Phone: [phone]
Fax: [phone]
Hotline
Phone: [phone]
[email protected]
www.theben.de