Theben 2080026 User manual

1
theRonda P360-101 M UP WH
2080025
theRonda P360-101 M UP GR
2080026
307231
1103105301
Presence detector
EN
1. Product characteristics
•Passive infrared presence detector for ceiling installation
•Circular detection area 360° to Ø 24 m (452 m2)
•Restriction of detection area with cover clips
•Automatic presence- and brightness-dependent control
for lighting and HVAC
•Mixed light measurement suitable for uorescent lamps
(FL/PL/ESL), halogen/incandescent lamps and LEDs
•Channel A light: relay, 230 V
•Choice of fully or semi-automatic operation
•Brightness switching value congurable, teach-in
function
•Reduction of time delay when briey present (short-term
presence)
•Connection option for push buttons or switches for
manual switching with automatic detection of push
button/switch
•Pulse function for staircase light time switch
•Channel H, presence: relay, oating e.g. for HVAC control
•Switch-on delay and time delay congurable
•Detection sensitivity congurable
•Ready for immediate use due to factory presetting
•Test mode for checking function and detection area
•Extension of detection area via master/slave or master/
master switching, a maximum of 10 detectors can be
switched in parallel with each other
•Ceiling installation in ush-mounted box
•Ceiling installation possible with back box (optional)
•User remote control theSenda S (optional)
•Management remote control SendoPro (optional)
•Installation remote control theSenda P (optional)
2. Safety
Danger of death through electric shock or fire!
Installation should only be carried out by a pro-
fessional electrician!
WARNING
•Work on electrical systems may only be carried out by
electricians or by instructed persons under the leader-
ship and supervision of an electrician in accordance with
the technical regulations applying to electricity!
•Comply with the country-specic safety regulations for
work on electrical systems! Ensure absence of voltage in
the cable before installation!
•The device is maintenance-free. If the device is opened
or penetrated with any objects the guarantee lapses.
3. Intended use
The presence detector is intended for interior installation. The
presence detector is exclusively intended for the use as con-
tractually agreed between the manufacturer and the user. Any
other use is considered to be unacceptable. The manufacturer
does not accept liability for any resulting damages.
4. Function
The presence detector is primarily used in entrance halls,
garages, store rooms, ofces and schools, as well as in homes,
for easy and energy-efcient control of lighting plus HVAC.
The switch contact „light“ switches lighting on with presence
and insufcient brightness, and off with absence or sufcient
brightness. The light can also be switched on/off manually
using push buttons or switches.
The „Presence“ switch contact controls heating, ventilation
and air conditioning systems. The contact closes when some-
one is present, a switch-on delay permits delayed switch on.
Functional description






Mixed light measurement
Presence detection
 Articial light
Push button for manual lighting control
Incident daylight

Settings on theRonda P360-101
Brightness set point value (lux)
Lighting time delay
Presence time delay
Presence switch-on delay
Mechanical safety lock

2
Light channel A
Switching response is controlled by presence and brightness.
The switch contact closes during darkness and when some-
one is present. It opens with a delay when there is brightness
or when no one is present.
Time delay
The time delay enables delayed switching off of lighting after
the room is vacated. The time delay is adjustable in a range
of 10 s to 60 min. If someone goes into an unoccupied room
only briey and leaves it within 30 seconds, then the light
shuts off prematurely after 2 minutes (short-term presence).
Push button control
The lighting can be manually switched at any time via a
push button or switch. If the light is switched on manually, it
will remain on for at least 30 minutes providing people are
present. It then switches off when the brightness is adequate.
The light is forced off after a preset time delay if the room
was (previously) vacated. If articial lighting is switched off
manually. the lighting remains switched off as long as the
room is occupied. The lighting switches again automatically
after the time delay has expired.
Fully or semi-automatic
Lighting control via the presence detector operates fully
automatically for increased comfort or semi-automatically for
greater energy savings. In „fully automatic“ the lights switch
on and off automatically. Light switching has to be completed
manually in „semi-automatic mode“. The lighting is always
switched off automatically.
Pulse function
Time delay can be set to pulse for controlling existing stair-
case light timer switch. The light output produces a pulse of
0.5 seconds duration every 10 seconds if people are present
or it is dark.
Channel presence H
Channel presence H is used for HVAC control. The switching
response of the oating contact is inuenced only by pre-
sence and not by brightness. If the contact is closed, the time
delay will be restarted at every movement. The contact is not
inuenced by the push button or switch.
Switch-on delay
The switch-on delay prevents instantaneous switch on. The
contact closes only on expiry of the switch-on delay, providing
people are constantly present.
Time delay
The time delay enables delayed switching off of HVAC devices
and systems after the room is vacated.
5. Detection area
The circular detection area of theRonda presence detector
covers a large detection area, and permits a complete room
coverage with many applications. Note that seated and
moving persons can be detected in differently-sized areas.
The recommended installation height is 2.0 m – 6.0 m. As
installation height increases, the sensitivity of the presence
detector decreases. Walking motions are necessary from ins-
tallation heights of 3.5 m and the detection areas of several
detectors should overlap in the marginal zones. The detection
range is reduced as temperatures increase.
Seated persons:
The details relate to smallest movements at table height
(approx. 0.80 m).
Moving persons:
At installation heights of between 5 and 10 m, the extent and
distance between the active and passive zones increase.
Installation
height (A)
Moving persons
Frontal (r)
Moving persons
Across (t)
Seated persons:
(s)
2,0 m 28 m2Ø 6 m 380 m2Ø 22 m 16 m2Ø 4,5 m
2,5 m 38 m2Ø 7 m 415 m2Ø 23 m 24 m2Ø 5,5 m
3,0 m 50 m2Ø 8 m 452 m2Ø 24 m 28 m2Ø 6 m
3,5 m 50 m2Ø 8 m 452 m2Ø 24 m 38 m2Ø 7 m
4,0 m 50 m2Ø 8 m 452 m2Ø 24 m – –
5,0 m 50 m2Ø 8 m 452 m2Ø 24 m – –
6,0 m 50 m2Ø 8 m 452 m2Ø 24 m – –
10,0 m 50 m2Ø 8 m 491 m2Ø 25 m – –
All gures are guidance values.
Brightness measurement
The presence detector measures articial light and daylight
that is reected directly below the detector. The light mea-
surement area maps a rectangle of about 2 x 3.5 m at table
height. The installation location is a reference point for the
lighting level. Direct light inuences the light measurement.
Avoid placing oor lamps or suspended lighting directly below
the detector. If the brightness measurement is deactivated,
the light channel A only switches depending on the presence
(brightness switching value set to „on“ via potentiometer or
set to „measurement off“ via the remote control).
Innen 2 m Fenster
Suitable lamps
The presence detector is designed for the operation of uo-
rescent lamps, compact uorescent lamps, halogen/incande-
scent lamps and LEDs. The maximum number of switchable
lights is restricted due to the high inrush current levels of
the EBs and LED drivers. The use of an external contactor

3
helps with large loads. Parallel switching enables allocation of
load to several Masters. All switched loads must be properly
suppressed.
6. Installation
Flush-mounted tting
The presence detector is ush-mounted using a size 1 stan-
dard ush-mounting installation socket.
Ceiling installation
A ceiling installation unit 73 A is available for simplied
ceiling installation of the presence detector (see accessories).
This also ensures cord grip and contact protection. The instal-
lation diameter is 72 mm (drill diameter 73 mm).
Surface-mount installation
A back box 110A is available for surface mount installation
(see accessories).
7. Switching
The presence detectors can be combined as master and slave:
master in individual switching, master in parallel switching,
master-slave parallel switching.
Several push buttons can connected to one control input.
Illuminated push buttons can only be used with neutral con-
ductor connection.
Individual switching
In individual switching, the presence detector as master
detects presence and brightness and controls lighting.
AC / DC
H2
H1
L’
Master/slave parallel switching
If the detection area covered by one presence detector is
insufcient (larger rooms), then up to 10 detectors can be
operated in parallel by connecting P terminals. In the process,
presence detection is performed by all detectors together. The
master measures the brightness, operates the push buttons
and controls the lighting. All other detectors are used as
slaves. They only provide presence information.

4
AC / DC
Master Slave
H2
H1
L’
•Light measurement only with the master
•Parameters are only set on the master
•Switch up to 10 detectors in parallel
•Use the phase with the same phase for all detectors.
Master: theRonda P360 -101 M
Slave: theRonda P360 Slave
Master/master parallel switching (for several
lighting groups)
Several masters can be used in parallel switching setup. Each
master controls its lighting group according to its own bright-
ness measurements. Delay times and brightness switching
values are set individually on each master. Presence continues
to be detected by all the detectors.
AC / DC
Master 1 Master 2
H2
H1
L’
H2
H1
L’
•One master with individual brightness measurement per
lighting group
•Set potentiometer and DIP switch individually for each
master
•Switch up to 10 detectors in parallel.
•Use the phase with the same phase for all detectors.
•The presence switch contact can be read by any master.
8. Settings
The presence detectors were supplied with basic settings
ready for operation. The specications are guidance values.
The „SendoPro 868-A“ and „theSendaP“ remote controls are
optionally available for start-up. They enable remote setting
of all potentiometer values settings from a distance.
Switch contact light settings
Potentiometer brightness switching value A „lux“
The required brightness switching value can be set via the lux
potentiometer.
The setting range is around 30 to 1000 lux. The factory pre-
setting is 300 lux.
Brightness switching values from 30 to 3000 lux can be set
via the management remote control.
Teach-in : When the lux potentiometer is moved to the
teach-in position, the LED start to ash for 20 seconds. As
soon as the LED stops ashing, the current measured bright-
ness value is accepted as the brightness switching value.
When the teach-in position is exited, the set value on the LUX
potentiometer is accepted as the new brightness switching
value.
Teach-in can also be carried out using the „SendoPro 868-A“
and „theSenda P“ remote controls. In this case, the current
measured brightness value is immediately accepted as the
brightness switching value.
The brightness measurement is deactivated at potentiometer
setting „on“. The channel light then switches only depending
on presence.
Potentiometer lighting time delay
The following guidance values have proved themselves in
practice and are recommended as settings:
•Transit zones (no work area) approx. 5 min
•Classroom approx. 10 min
•Work areas (ofce, meeting room) approx. 10 min
• „Pulse“ : Control staircase light time switch (0.5 s „on“
/10 s „off“)
Switch contact presence H settings
Potentiometer presence time delay
The contact closes if people are present and opens when the
room is vacated after the time delay expires.
Potentiometer presence switch-on delay
•The contact only closes when someone is present after
expiry of the switch-on delay
•0 = contact closes immediately if people are present

5
Parameters and control commands via remote
control
The following parameters can be queried or changed via
the remote control for support during installation as well as
servicing:
Parameter Description SendoPro
can be
queried
868-A
SendoPro
be changed
868-A
theSenda
P can be
changed
Brightness
switching
value A
Value range in lux x x x
Measurement off x x x
Time delay
A
Value ranges
in seconds and
minutes
x x
Pulse x x
Short pre-
sence A On /Off x
Time delay
H
Value ranges
in seconds and
minutes
x x
Switch-on
delay H
Value ranges
in seconds and
minutes
x
Congura-
tion type auto /man x x x
Control
input S
Auto /switch /
push button S /
push button O
x
Detection
sensitivity
(PIR)
Value range in
levels x x
Group
address All /I /II /III x x
LED display
movement Off /On x
The parameters are sent to the presence detector with the
„SendoPro 868-A“ management remote control or with „the-
Senda P“ installation remote control via infra-red. Changed
parameters are immediately applied and used by the detector.
With the „SendoPro 868-A“ management remote control,
parameters can be queried by sending values level-by-level
to the detector. If the sent values are below the set parame-
ter, the LED illuminates briey. If the sent values are equal or
above the set parameter, the LED ickers for 2 seconds.
The following control commands can be triggered
with the remote control:
Control command Description Can be trigge-
red SendoPro
868-A
Can be
triggered
theSenda P
Teach-in channel
AActivate x x
Switch lights
on/off
Lighting group can be
switched on and off. x x
Presence test On /Off x x
Restart Restart detector x x
Factory
regulations
Set all parameters
and settings to factory
setting.
x
Brightness switching value A
The brightness switching value denes the minimum desired
brightness. The current prevailing brightness is measured
below the presence detector. If the prevailing brightness is
below the switching value, the light switches on when a pre-
sence is detected (in conguration type fully automatic).
Value range
Lux values with "SendoPro 868-A" management remote
control
In the installation remote control "theSenda P", the
following values are available
(The currently measured brightness value (Lux) can
be adopted with the "SendoPro 868-A" management
remote control, with the teach-in control command or
with the “theSenda P” installation remote control via the
teach-in button.)
Values outside the permitted range will automatically be
set to the appropriate limit value.
30 - 3000 Lux
30, 300, 500,
800 lux
- Deactivating the brightness measurement (the bright-
ness has no inuence)
- The light channels only switch after presence/absence.
Possible with "SendoPro 868-A" management remote
control or "theSenda P" installation remote control.
Measurement
off
Button
Time delay A
Value range
Adjustable values with "SendoPro 868-A" manage-
ment remote control
In the "theSenda P" installation remote control, the
following values are available
10 s - 60 min
10 s, 30 s, 60 s, 2
min, 10 min, 20 min,
60 min
Control for staircase light timer switch (0.5 s "on"
/10 s "off")
"SendoPro 868-A"
"theSenda P"
Pulse
Button 1
Short-term presence
The time delay of channel A light can be switched off sooner
if a room is occupied only for a short time. (In fully automatic
device and semi-automatic device conguration type)
The switch-off delay time is used according to set parameters. Off
If someone enters an unoccupied room and it is only occupied for
up to 30 seconds, the light goes off 2 minutes early.
On
Time delay H
The presence channel always switches, regardless of whether
conguration type is set to fully automatic or semi-automa-
tic“. The set values remain unchanged. The relay contact opens
once the room is vacated after the set time delay expires.
Value range
Adjustable values "SendoPro 868-A" 10 s ... 120 min.
Adjustable values "theSenda P" 10 s, 30 s, 60 s, 2
min, 10 min, 20 min,
120 min
Switch-on delay H
The presence channel always switches, regardless of whether
conguration type is set to fully automatic device or semi-
automatic device. The relay contact only closes when some-
one is present after expiry of the set switch-on delay.

6
Value range
Adjustable values 0 s, 30 s, 1 ...10 min
No switch-on delay (relay contact closes immedia-
tely when someone is present) 0 s
Adjustment only possible with „SendoPro 868-A“.
Conguration type
Fully automatic device: The lighting switches on and off automa-
tically. (due to presence/no presence and brightness)
„SendoPro 868-A“
„theSenda P“
auto
Button A
Semi-automatic: Switch on must always occur manually. Switch
off occurs automatically by the presence detector. (due to pre-
sence or brightness)
„SendoPro 868-A“
„theSenda P“
man
Button
Control input S
Control input S for manual switch on/off of channel A light
automatically detects push buttons or switches.
Several push buttons can be connected to control input S
Use light push button only with neutral conductor connector
Value range
Automatic detection of push button or switch. A signal that
is present for than 0.7 s is detected as a push button. Longer
signals are evaluated as a switch.
auto
To adapt to user behaviour, the type of
signal transmitter used can be set to
xed. Automatic detection is deactivated.
When selecting the push button, ope-
ning contact or NO contact can also be
specied.
Switch
Push button (NO
contact)
Push button (ope-
ning contact)
Switch
Push button
S
Push button
O
Conguration possible only with „SendoPro 868-A“.
Detection sensitivity
The detector has 5 sensitivity increments. The basic setting
is the middle level (3). By selecting the operation mode test
presence, the set sensitivity increment is not changed.
With the „SendoPro 868-A“ management remote control,
levels 1 to 5 can be selected and sent to the detector.
With the „theSenda P“ installation remote control, the sen-
sitivity can be reduced or increased by one level with every
button press.
Level Sensitivity
1 very insensitive
2 insensitive
3 Standard
4 sensitive
5 very sensitive
Group address channel A
This parameter is applied when using the „theSenda P“ user
remote control. A group address can be assigned to the chan-
nel A light.
The „SendoPro 868-A“ or „theSenda S“ can be used to pro-
gram the group addresses in the detector.
Group address value range
Adjustable values "SendoPro 868-A" I, II , III , All
Adjustable values "theSenda S" I, II
LED display motion
The motion detection can be displayed via the LED.
Value range
No display of motion detection. Off
The LED switches on when motion is detected, otherwise swit-
ches off.
On
Adjustment possible only with „SendoPro 868-A“.
Teach-in channel A
With teach-in, the currently measured brightness value is
accepted as brightness switching value A. Values outside the
permitted range will automatically be set to the appropriate
limit value.
The control command teach-in can be adopted with the
„SendoPro 868-A“ management remote control or with the
„theSenda P“ installation remote control via the button.
Factory settings
The theRonda P360-101M presence detector is supplied with
the following parameter values:
Parameter Value
Brightness switching value A 300 lux
Time delay A 10 min
Short presence A On
Time delay H 10 min
Switch-on delay H 0 s
Conguration type auto
Control input S auto
Detection sensitivity (PIR) Stage 3
Group address T
LED display movement Off
9. Start-up
Switching behaviour
Every time the power supply is switched on, the presence
detector runs through two phases that are shown on an LED:
1. Start-up phase (30 s)
•The red LED ashes every second, both switch contacts
are closed (light and presence on).
•The detector does not react to push button commands
and remote control commands.
•When no one is present both contacts open after 30
seconds.

7
2. Mode
The detector is ready for operation (LED off).
Test presence
Presence test mode is used to test presence detection and
wiring. Presence test mode can be activated with the „Sendo-
Pro 868-A“ management remote control and with the „the-
Senda P“ installation remote control.
Setting the presence test mode via remote control
•The detector goes directly into test mode when the test
mode is set via the remote control:
 Every movement is indicated by the LED.
 When movement occurs the light and presence switch con-
tacts close.
 When no one is present the light switch contact opens after
10 seconds.
 Brightness measurement deactivates, detector does not react
to brightness.
 The detector reacts as in fully automatic function mode even
if semi-automatic is set.
 Teach-in cannot be activated in test mode.
•Test mode ends automatically after 10 mins. The detector
performs a new start (see switch-on behaviour).
10. Technical data
Operating voltage 110-230 V AC + 10 % /- 15%
Frequency 50-60 Hz
Upstream protection device: 13 A
Power consumption approx. 0.1 W
Type of installation Ceiling installation; Flush/
surface mounted or ceiling
installation
Installation height 2,0 – 3,5 m / max. 10 m
Minimum height > 1.7 m
Detection area horizontal
vertical
360°
120°
Maximum range Ø 8 m (Mh. 3 m) / 50 m2radially
moving
Ø 24 m (Mh. 3 m) / 452 m2
tangentially moving
Setting range brightness switching value 30 – 3000 Lux
Lighting time delay 10 s – 60 min / Pulse
Presence time delay 10 s – 120 min
Switch-on delay "Presence" 0 s – 10 min
Channel A light Relay 230 V /10 A, µ-contact
Max. switching capacity cos j1
resistive 2300 W
Max. switching capacity cos j 0.5 1150 VA
Max. switching capacity LED
LED lamps < 2 W
LED lamps > 2 W
see manufacturer concerning
cos j
60 W
180 W
Guidance value max. switch-on peak 800 A / 200 µs
Maximum number EBs T5/T8 16 x 54/58 W, 24 x 35/36 W
8 x 2 x 54/58 W
12x 2x 35/36 W
Channel H, presence Floating relay, basic insulation
Maximum voltage 220 V DC / 250 V AC
Maximum switching capacity 50 W / 50 VA (max. 2 A)
Recommended minimum load 10 mV /10 mA
Connection type Terminals screws
Max. cable cross-section max. 2 x 2.5 mm²
Flush-mounted socket size Siz. 1, Ø 55 mm (NIS, PMI)
Protection rating IP 54 (installed)
Ambient temperature -15 °C – 50 °C
CE Declaration of Conformity This device conforms to the
safety regulations of the EMC
directive 2014/30/EU and of
2014/35/EU.
Product overview
Type of
installation
Channel Ope-
rating
voltage
Colour Type Item No.
Ceiling
installation
Light |
HVAC
110-
230 V
AC
White theRonda
P360 -101 M
2080025
Ceiling
installation
Light |
HVAC
110-
230 V
AC
Grey theRonda
P360 -101 M
2080026
Ceiling
installation
Light |
HVAC
110-
230 V
AC
Special colour
in accordance
with customer
information
theRonda
P360 -101 M
2080028
Troubleshooting
Fault Cause
Light does not switch
on and/or off if pre-
sence is detected and
in darkness
Lux value is set too low; detector set on semi-
automatic; light was switched off manually via
push button or „theSenda S“; person not within
detection range; obstruction(s) interrupting detec-
tion; time delay set too short
Light stays on with
detection of presence
despite sufcient
brightness
Lux value is set too high; light was briey switched
on manually via push button or with „theSenda S“
(wait 30 min.); detector is in test mode
Light does not switch
off and/or light
switches on spontane-
ously when no one is
present
Wait for switch-off delay (self-learning);
Thermal sources of interference in the detection
area: fan heaters, incandescent lamps/halogen
spotlights, moving objects (e.g. curtains hanging in
an open windows);
Load (EBs, relays) not cleared
Push button does not
function
Device still in the start-up phase; illuminated push
button was used without neutral conductor;
Push button not led to the master
Light cannot be swit-
ched off with the push
button
Push button not fed to the detector. Check wiring
to the push button.
Device does not
respond
Short circuit or several phases in parallel swit-
ching! Disconnect detector from the power supply
for 5 mins. (thermal fuse)
Error ashing
(4 x per second)
Error in self-test;
Device not properly functional!
LED display
LED Description
Blinking in 1 second cycle The presence detector is in the start-up phase.
Flickering for 2 s The command sent from the remote control
via infrared was accepted by the presence
detector.
Lights up briey The command sent from the remote control via
infrared was rejected by the presence detector.
The command is not valid. Check the detector
type or parameter selected in the SendoPro.
Fast blinking Error blinking; The presence detector has
found an error.
Flickering for 20 s Teach-in via potentiometer is activated.

8
LED Description
Lights or ickers
irregularly
The presence detector is in presence test
mode or "LED display movement" is activated.
The LED displays detection of movement.
Guarantee
Theben HTS presence detectors are manufactured with the
utmost care and using state-of-the-art technology and are
quality-tested. Theben HTS AG therefore guarantees perfect
operation when used correctly. Should a fault occur, however,
Theben HTS AG will full the guarantee within the scope of
the general terms and conditions.
Please note in particular:
•that the guarantee period lasts 24 months from the date
of manufacture.
•that the guarantee is invalidated if you, or a third party,
make changes or undertake repairs to the devices.
•that, insofar as the presence detectors are connected
to a software-controlled system, the guarantee for this
connection is only valid when the indicated interface
specication is complied with.
We undertake to repair or place as quickly as possible all
components of the delivered device that have become
defective or unusable through demonstrably poor material,
faulty construction or incomplete delivery up to the end of the
guarantee period.
Returns
In the event of a guarantee claim, please return the device to
the relevant dealer together with the delivery note and a brief
description of the fault.
Industrial property rights
The design as well as hardware and software of these devices
are protected by copyright.
Dimensional drawings
11. Accessories
Back box 110A WH
Item No.: 9070912
Details > www.theben.de
Back box 110A GR
Item No.: 9070913
Details > www.theben.de
SendoPro 868-A
Item No.: 9070675
Details > www.theben.de
DE (ceiling installation) box 73A
Item No.: 9070917
Details > www.theben.de
Covering clip for area restriction
Item No.: 9070921
Details > www.theben.de
theSenda S
Item No.: 9070911
Details > www.theben.de

9
theSenda P
Item No.: 9070910
Details > www.theben.de
12. Contact
Theben HTS AG
Im Langhag 7b
8307 Effretikon
SWITZERLAND
Phone [phone]
Fax [phone]
Hotline
Phone [phone]
[email protected]
www.theben-hts.ch
All countries except Switzerland
Theben AG
Hohenbergstraße 32
72401 Haigerloch
GERMANY
Phone: [phone]
Fax: [phone]
Hotline
Phone: [phone]
[email protected]
www.theben.de