Theben LUXA 103-100 DE WH User manual

1
LUXA 103-100 DE WH
1030012
LUXA 103-101 DE WH
1030013
307343
Motion detector
EN
1. Basic safety information
Danger of death through electric shock or fire!
 Installation should only be carried out by a
qualied electrician!
WARNING
•The device conforms with EN 60669-2-1 if installed
correctly
2. Proper use
•Motion detector for automatic lighting control dependent
on presence and brightness; LUXA 103-101 DE: suitable
for automatic lighting and HVAC control
•Suitable for ceiling installation (false ceilings) indoors
•Suitable for toilets, small rooms, workplaces, ofces, etc.
Disposal
Dispose of the device in an environmentally sound manner
(electronic waste)
3. Device description
Sensor unit
Power supply unit
3 potentiometers for setting
time delay (TIME), bright-
ness value (LUX) and detec-
tion area (metres);
additional setting of HVAC
time (TIME 2) in the case of
LUXA 103-101 DE
red LED
4. Installation and connection
!Secure device with an upstream type C circuit breaker
(EN 60898-1) with a maximum of 10 A.
!Secure device with an upstream type C circuit breaker
(EN 60898-1) with a maximum of 6 A (HVAC channel 2).
Installing the motion detector
LInstallation height: 2 – 3 m
LCable length: 100 cm
LMotion detector requires clear line of sight to people
Disconnect power source
0FF
230V
Create a ceiling opening of Ø 65 mm
=65
Ø
6 - 8 m m
5 0 - 6 0 m m
Screw open and ip open the power supply unit
Connect power supply unit and sensor unit according to the
wiring diagram
LRecesses in the power supply unit can be adjusted to the
cable diameter (min. Ø 3 - max. Ø 12.5 mm)
Ø 3 - Ø 6 mm Max. Ø 12.5 mm
!ATTENTION: the network connector must be rmly in place
Push the power supply unit through the ceiling opening
and attach the sensor with tensioned springs in the ceiling
Ø= 65
Connect motion detector to power supply

2
The device need
60 seconds to warm up.
Connecting the motion detector
Danger of death through electric shock or fire!
 Installation should only be carried out by a
qualied electrician!
WARNING
Disconnect power source
Ensure device cannot be switched on
Check absence of voltage
Earth and bypass
Cover or shield any adjacent live components
The warm-up phase takes approx. 60 s. The LED is perma-
nently red.
L NLL‘ N R
N
L
L NL N R D1 D2
N
L
L‘
LUXA 103-100 DE LUXA 103-101 DE
Installation instructions and detection area
As the detector reacts to variations in temperature, avoid the
following situations:
Do not direct motion detectors at objects with highly-
reective surfaces such as mirrors, etc.
Do not install the motion detector near heat sources, such
as heating outlets, air conditioning systems, lamps, etc.
Do not direct the motion detector at objects that move in
the wind, such as curtains, large plants, etc.
Pay attention to the direction of motion during the test run.
3,5 m
4 m
7 m
2 m
Lrecommended installation height: 2.5 m
5. Walking test
The walking test is used to test the detection area.
Set the time delay potentiometer (TIME 1) to Test. The
motion detector only reacts to movements, brightness
measurement is switched off.
Walk through the detection area. Every detected movement
is indicated by the LED, and the light switch contact closes
for 2 s.
2 sec
Test
OPEN
2030 10

6. Setting
The motion detector LUXA 103-100 DE has 3 potentiome-
ters for setting the time delay (TIME 1), brightness (LUX) and
sensitivity (METRES); with LUXA 103-101 DE the HVAC time
(TIME 2) can also be set.
LUXA 103-101 DE




Setting the brightness (LUX)
You can set different brightness values (LUX) with the
potentiometer.
If you want to change the preset brightness
Set the potentiometer to the desired brightness
(10 – 2000 lux = )
If you want a specic brightness value to be learned using the
teach-in function
At the desired brightness, set the potentiometer to . The
LED ashes for 20 s, afterwards the measured brightness
value is accepted.
Leave the potentiometer at position .

3
Setting the time delay (TIME 1)
If the motion detector detects no further movement, it swit-
ches off after the set time delay.
If you want to change the preset time
Set the potentiometer to the desired time (5 s - 30 min).
If you want to use the pulse function (e.g. for a staircase light
timer switch)
Set the potentiometer to . The presence detector for
"staircase light timer switch" operation is on for 1 s and off
for
9 s.
Setting the HVAC time (TIME 2) (only LUXA 103-101 DE)
Set the potentiometer to the desired time (10 s - 60 min.).
Setting the sensitivity (METRES)
You can reduce the sensitivity in order to avoid switching
errors.
Set potentiometer METRES to the desired
sensitivity.
Manual operation
The lighting can be manually switched on/off via a button.
L NLL‘ N R
N
L
When the light is on
Briey press button once (< 1 s)
▻Light is off
When the light is off
Briey press button once
▻The light is on for the time set on the potentiometer;
then the detector goes into automatic mode
Limiting the detection area
Use the supplied cover clips to adjust the motion detector
to the desired detection area.
Remove the required section of the cover clip by using
pliers or similar.
Then place it on the lens.
A
B
7. Technical data
Operating voltage 230 V AC ±10%
Frequency 50 Hz/60 Hz
Upstream protection device 10 A
Standby output 0.5 W
Switching capacity min. 10 mA
Protection rating IP 44 (detector), IP 20 (power supply
unit) in accordance with EN 60529
Protection class II
Operating temperature 0 °C … +45 °C
Brightness setting range 10 – 2000 lx/∞
Duty cycle range LUXA 103-100: 5 s – 30 min for
lighting
LUXA 103-101: 5 s – 30 min for
lighting
10 s – 60 min for HVAC
Detection angle 360°
Detection area lateral/frontal: 7 m/4 m
Installation height 2 – 3 m (2.5 m recommended)
Light switch output µ contact 230 V AC, zero-cross
switching
Switch output HVAC (D1/D2) LUXA 103-101: 5 A (at 250 V AC,
cos ϕ= 1) µ contact
Min. switching capacity 10 mA
Incandescent lamp load max. 2000 W
Halogen lamp load max. 2000 W
Low-voltage halogen lamps
(transformer)
max. 1000 VA
Fluorescent lamps (LLB low-loss
ballasts):
parallel compensated max. 900 VA, 100 µF
Fluorescent lamps (EB – electronic
ballasts)
600 W
Compact uorescent lamps (EB) 400 W
LED lamps (< 2 W) 35 W
LED lamps (> 2 W) 400 W

4
8. Contact
Theben AG
Hohenbergstr. 32
72401 Haigerloch
GERMANY
Tel. [phone]
Fax [phone]
Hotline
Tel. [phone]
[email protected]
Addresses, telephone numbers etc.
www.theben.de