THOMSON TM-SAU01R User manual

Instruction Manual
Model: TM-SAU01R
Read this booklet thoroughly before use and save it for future reference.
Recycle used batteries,
paper and plastic.
V1.0
801
Sparkling Beverage Maker

1
Table of Contents
1. Disclaimer 1
2. Emergency Handling & Warnings 2
3. Safety Precautions 2
4. Feature Descriptions 4
5. Part Names 4
6. Installation 5
7. Instructions 6
8. Simple Troubleshooting 7
Disclaimer
Declaration:
This manual has been reviewed and proofread carefully; however, typographical and
technical errors may still remain. If there are mismatches to the actual machine due to
errors, please refer to the actual machine; such errors or omissions may not be used as
evidence in a court of law, and will be corrected with a new revision.
Our company reserves the right to change all contents in this manual at any time without
prior notice.

2
Emergency Handling & Warnings
Contact the customer service hotline of our company or a dealer nearby when
abnormalities occur.
Do not expose this machine to rain or humidity.
Safety Precautions
Soda Maker
Clean with a wet cloth; mild cleansers may be
used. Do not use any corrosive solvents; they will
cause the machine surface to erode.
Carbonating Bottle
1. Do not wash the plastic carbonating bottle in the
dishwasher or dry with a dish dryer; do not store
it in the freezer to prevent deformation.
2. Wash with clean water or mild cleansers. Do not
use hot water over 40°C.
3. Clean the plastic carbonating bottle regularly.
4. If the carbonating bottle is not needed after use,
leave the cover open to keep the bottle dry.
5. The storage temperature of the carbonating
bottle is between 1°C-40°C.
6. Cease usage immediately if bottle has
deformed, changed color or been damaged.
1. Check the Soda Maker and accessories (CO2 carbonator and plastic carbonating
bottle); contact your purchasing dealer immediately if damage or flaws are discovered.
2. Do not use the machine before flaws and damage are repaired.
3. Do not make any modifications or repairs to this product; repairs must only be
performed by us and authorized servicing staff.
4. Only genuine accessories may be used; failure to do so will void the warranty.
Dishwasher
Mild cleanser
Clean Leave it open to
keep it dry

3
Safety Precautions
Concerning the Use of the Soda Maker
This Soda Maker is specifically for making carbonated beverages. Do not place the
equipment near heat sources; avoid exposure to direct sunlight. Place the machine on a
flat and waterproof surface every time it is used; keep it in an upright position during the
operation process. Do not tilt the machine.
The CO2 carbonator must be removed during transport; do not rinse it directly with water.
Carbonating Bottle Usage
Cease usage immediately and replace with a new carbonating bottle when there are
anomalies such as scratches, damage or color changes, etc., or if its effective period of
use has expired.
CO2 Carbonator
Only genuine dedicated CO2 carbonators can be used with the Soda Maker to keep the
warranty valid.
Caution: The CO2 carbonator is pressurized; store it in a shady place (under 50°C). Avoid
exposure to direct sunlight or any heat sources.
1. Do not heat up the carbonator.
2. Do not place the carbonator in the refrigerator.
3. Do not touch the carbonator if its temperature is too low to avoid frostbite.
4. Keep the carbonator in an upright position; store in a shady place.
5. Do not remove the carbonator during the carbonating process.

4
Feature Descriptions
1. A soda maker with a patented design that can carbonate
juices, liquor and beverages directly.
2. Carbonates sweetened beverages (flat) directly.
3. Gives flat coke and liquor a sparkling taste immediately.
4. Food grade CO2 with purity up to 99.9%.
5. Zero power consumption, safe, portable, DIY with no added
chemical ingredients.
6. Passed SGS food grade material certification.
7. Original connector with even bubbles.
8. Patented design latch; operates easily and conveniently.
9. The carbonator can be used repeatedly; healthy and
environmentally friendly.
10. Original discharge valve button; operates easily and safely.
11. The carbonating bottle is made with food grade PET
materials; it does not contain bisphenol A (able to withstand
12 bars of pressure).
First of all, thank you for your support.
With the exclusive functions and designs of this Soda Maker, you can turn flat water into
rich tasting carbonated water, or add any flavors you prefer to create your own carbonated
beverage.
Part Names
Carbonating Bottle and
Cover
CO2
Carbonating
Device
CO2 Exhaust
Pipe
CO2 Carbonator
CO2 Carbonator
Fixture Location
CO2 Carbonator
Protective Seat
CO2 Carbonating
Button
Main Machine
Carbonating Device
Connection Pan
Slow Pressure Release
Device (silver)
Quick Pressure Release
Button (blue)

5
Installation
Step 1: Remove the protective cover
of the carbonator fixture seat.
Step 2: Rotate the carbonator
counterclockwise to tighten it into the
fixture seat.
Step 3: Adjust the connection pan of
the carbonating device to a tilted state;
connect the CO2 carbonating device.
Caution: Do not connect the CO2
carbonating device when the
carbonating device connection pan is
in a parallel state; products damaged
due to this misuse will not be covered
by the warranty.
Step 4: Pour cold water or any other
beverage into the carbonating bottle;
do not exceed the fill line marked on
the bottle.
Step 5: Lock the carbonating bottle
onto the CO2 carbonating device; use
the instructions of Step 3 to connect
the carbonating device connection
pan.
Step 6: Press the CO2 carbonating
button until you hear a hiss after it is
connected; this means it is fully
carbonated. If you prefer stronger
bubbles, continue to press the button to
inject more CO2.
Caution: Do not press and hold down
the button for long periods of time; press
for approximately 0.5-1 second each
time.
Step 7: Adjust the carbonating
connection pan to a tilted state once
carbonation is complete to remove the
carbonating bottle.
Continued Use:
Step 8: It will be in a slow pressure release status
once the silver cover is opened; slow pressure release
is recommended for sparkling drinks. The blue quick
pressure release button can be pressed for sparkling
water to avoid waiting for too long. The CO2
carbonating connector can be removed by rotating it
counterclockwise once pressure release is complete.
Step 9: Use of cold water or beverages
(0.5°C-5.5°C) is recommended; it will give you a
more pleasant taste when drinking.

6
Instructions
Reminder:
1. To prevent damaging the carbonating bottle, adding flavoring syrup in another
container (glass bottle or cup) after making sparkling water is recommended. Use cold
water between 5-10°C to give it better taste when drinking.
2. If flat beverages are carbonated directly instead of water, follow the recommended fill
lines marked on the carbonating bottle.
Replacing and Exchanging the CO2 Carbonator
If the sparkling water is not as bubbly or the water does not carbonate at all, the CO2
carbonator might be out of gas. Replace it with the same model of CO2 carbonator.
Genuine CO2 carbonators can be purchased from your dealer; please visit our website at:
www.wonder.tw for more information.
Caution: Do not replace the CO2 carbonator when the carbonating bottle is still on the
machine.
1. Remove the purple dust-proof cover of the new CO2 carbonator.
2. Remove the carbonating bottle from the machine before exchanging the CO2
carbonator.
3. Rotate the carbonator clockwise to remove it.
4. The empty carbonator can be refilled according to the refilling method of CO2
carbonators; replace the carbonator for the price of refilling.
5. Follow the instructions in the previous chapters: Replace the CO2 carbonator by
using the instructions from the previous chapters to continue using the Soda
Maker.
Refilling the CO2 Carbonator
When the CO2 carbonator is depleted, call our toll free hotline [phone] or scan the
following QR-code.
Or visit our official website: to locate a service station nearby for refilling and replacement;
do not refill the CO2 carbonator by yourself. The carbon dioxide inside the CO2
carbonator is food grade and complies with all quality and safety standard tests.

7
Simple Troubleshooting
Problem Possible Cause Solution
Water overflows when using
the machine.
The carbonating button was
pressed for too long.
The water was too full.
1. Press the pressure release button to release
excess CO2
2. The correct carbonating method is to press
the carbonating button for 0.5 seconds each
time for 2-3 times; fill the water up to the fill
line.
The carbonating bottle cannot
be removed after making
sparkling water.
Excessive CO2 in the bottle
was not fully released.
Press the pressure release button to release
excess CO2
And the carbonating bottle can be removed.
The sparkling water has few
bubbles.
The CO2 carbonator might be
out of gas.
The carbonator temperature is
too low.
The water temperature is too
high.
Replace the CO2 carbonator using the
instructions previously described.
Leave the CO2 carbonator; wait until its
temperature increases to room temperature.
Use drinking water with a lower temperature.