Threshold Studio McGee Marvale TGT60CTB User manual

>> Assembly instructions
TM
© 2023 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
Marvale Console Table
Style # TGT60CTB
DPC-item #: 249-17-1316

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time.
Good luck – though we’re confident you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a work surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
tools needed (only hex wrench included)
For tipping restraint hardware kit only.
power drill
Hex wrench

hardware
(H4) x 1
hex wrench
(H1) x 28
1/4” x 15 mm bolt
(H2) x 28
lock washer
(H3) x 28
flat washer
(H5) x 2
tipping restraint hardware kit
(inside plastic bag)
pare hardware
3

TEM DESCR PT ON QTY
A Top panel 1
B Side frame 2
C Middle leg 2
D Top stretcher 4
E Bottom stretcher 4
F Middle stretcher 1
C
E
B
A
D
exploded diagram
F
B
C
D
D
D
E
E
E
4

x 2
1.1. Orient and attach two top stretchers (D) to one middle leg (C) with two15 mm bolts (H1), two lock washers (H2) and two flat washers (H3) as shown.
1.2. Repeat the same process to attach the other middle leg (C).
step 1: attach top stretchers to middle legs
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
(H4) x 1
hex wrench
(H1) x 4
1/4” x 15 mm bolt
(H2) x 4
lock washer
(H3) x 4
flat washer
The metal tabs face in the same direction as the middle
U-shaped bracket and flush with the top of middle leg.
D
D
C
H1
5
H2
H3
H1
H2
H3

step 2: attach the assembled top stretchers to top panel
2.1. Lay the top panel (A) upside down on a level and protected surface.
2.2. Align and attach one assembled middle leg with top stretchers (D) to the top panel (A) with four 15 mm bolts (H1) and four washers (H2 and H3).
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
A
D
H1
H2
H3
D
C
6
(H4) x 1
hex wrench
(H1) x 4
1/4” x 15 mm bolt
(H2) x 4
lock washer
(H3) x 4
flat washer
H1
H2
H3
H1
H2
H3
H1
H2
H3
The metal brackets face inward.

step 3: attach middle stretcher to the middle leg
3.1. Orient and fit the middle stretcher (F) onto the U-shaped bracket on the assembled middle leg (C) and secure it into place with one 15 mm bolt (H1), one lock
washer (H2) and one flat washer (H3).
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
7
(H4) x 1
hex wrench
(H1) x 1
1/4” x 15 mm bolt
(H2) x 1
lock washer
(H3) x 1
flat washer
C
F
F
C
H1
H2
H3
C
F

step 4: attach the other middle leg to the middle stretcher
4.1. Repeat the same process to attach the other assembled middle leg (C) to the other end of the middle stretcher (F). Make sure that the metal tabs overlap
the threaded inserts on top panel (A) properly.
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
8
(H4) x 1
hex wrench
(H1) x 1
1/4” x 15 mm bolt
(H2) x 1
lock washer
(H3) x 1
flat washer
C
F
C
F
F
C
H1
H2
H3

step 5: secure the top stretchers to the top panel
5.1. nsert four 15 mm bolts (H1) with washers (H2 and H3) through the metal tabs on the assembled top stretchers (D) and screw into the top panel (A).
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
9
(H4) x 1
hex wrench
(H1) x 4
1/4” x 15 mm bolt
(H2) x 4
lock washer
(H3) x 4
flat washer
H1
H2
H3
D
H1
H2
H3
H1
H2
H3
H1
H2
H3
D
A

E
step 6: attach bottom stretchers to middle legs
6.1. Orient and fit the bottom stretchers (E) onto the U-shaped bracket on the assembled middle legs (C) and secure into place with four 15 mm bolts (H1) and
four washers (H2 and H3).
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
10
(H4) x 1
hex wrench
(H1) x 4
1/4” x 15 mm bolt
(H2) x 4
lock washer
(H3) x 4
flat washer
E
E
E
C
C
C E
E
E
E
C
H1
H2
H3
E
H1
H2
H3

step 7: attach one side frame to the previous assembly
7.1. Align and attach one side frame (B) to the previous assembly with five 15 mm bolts (H1) and five washers (H2 and H3).
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
11
(H4) x 1
hex wrench
(H1) x 5
1/4” x 15 mm bolt
(H2) x 5
lock washer
(H3) x 5
flat washer
B
B
E
E
A
A
E
H1
H2
H3
E
H1
H2
H3
B
E
B

step 8: attach the other side frame to the previous assembly
8.1. Repeat the same process with the other side frame (B).
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
12
(H4) x 1
hex wrench
(H1) x 5
1/4” x 15 mm bolt
(H2) x 5
lock washer
(H3) x 5
flat washer B
E
E
E
H1
H2
H3
E B
E
B
B
A
H1
H2
H3
A

step 9: adjust the pre-attached floor levelers
CAUTION: Heavy! You may
need assistance with this step.
9.1. Now, go back and securely tighten all the bolts. Make sure all the parts are tight and there are no gaps between the parts. This will help keep the unit square.
9.2. Ask for assistance to lift the assembled unit upright. DO NOT lean the table by the legs.
9.3. Adjust the pre-attached floor levelers to level the unit, if necessary.
Floor leveler
13

step 10: install the tipping restraint hardware kit
10.1. Follow the instructions printed on plastic bag containing tipping restraint hardware to attach tip-over restraint between the unit and wall.
NOTE: You must use this tipping restraint to attach this unit to the wall, to prevent accidents and/or injures.
Nylon strap
Tools required: Phillips screwdriver, stud finder, tape measure, pencil, power drill and 1/8” drill bit (not provided).
Metal bracket
Short screw
Wooden stud
Wall
Wall
Long screw
(H5) x 2
tipping restraint hardware kit
(inside plastic bag) H5
14

FURNITURE TIPPING RE TRAINT
YOUNG CH LDREN MAY BE NJURED BY T PP NG FURN TURE AND YOU MUST USE TH S T PP NG
RESTRA NT TO ATTACH TH S UN T TO THE WALL, TO PREVENT ACC DENTS AND/OR NJUR ES.
TO PROV DE PROTECT ON AGA NST THE UNEXPECTED T PP NG OF
FURN TURE DUE TO MPROPER USE.
USE OF T P-OVER RESTRA NTS MAY ONLY REDUCE, BUT NOT EL M NATE, THE R SK OF T P-OVER.
WARNING
 Unit must be placed on a level surface or leveled with included hardware (when applicable).
 Do not sit or stand on or allow children to climb, sit or stand on the assembled product.
 For safety reasons, it is imperative that this unit be mounted to the wall.
 Do not use without installing the tip restraint.
 Unit can tip over causing severe injury or death.
 Do not exceed the recommended weight limits.
 Evenly distribute the weight on each level and always keep the heavier loads on the bottom.
 Before cutting, drilling or hammering into any wall or floor surface, verify the location of electrical,
plumbing and gas lines. Cutting may cause serious injury.
15

Care and Maintenance
 Use a soft, clean cloth that will not scratch the surface when dusting.
 Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
 Using solvents of any kind on your furniture may damage the finish.
 Never use water to clean your furniture as it may cause damage to the finish.
 Always use coasters under beverage glasses and flowerpots.
 Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill gently. Avoid rubbing.
 Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create spotting within the furniture finish.
 Stains or marks from crayons or ink markers will be difficult to remove.
 n the event that your furniture is stained or otherwise damaged during use, we recommend that you call a professional to repair your furniture.
 Check bolts/screws and nuts periodically and tighten them if necessary.
Further Advice about Wood Furniture Care
t is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity changes can cause fading, warping, shrinking and
splitting of wood. t is advised to keep furniture away from direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful tips will enhance your furniture as it ages.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace it for up to one (1) year from date of purchase.
Every Whalen Furniture product is designed to meet your highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province.
Customer Service: 1-855-MYTGTHOME (855-698-4846)
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenfurniture.com
16

M A X I M U M R E C O M M E N D E D W E I G H T L O AD
MAX MUM LOAD 45.4 kg / 100 lb
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Marvale Console Table
MODEL # TGT60CTB
TH S UN T S NTENDED ONLY FOR USE W TH N THE MAX MUM WE GHTS ND CATED. USE
W TH LOADS HEAV ER THAN THE MAX MUM WE GHTS ND CATED MAY RESULT N NSTAB L TY, CAUS NG POSS BLE
NJURY.
17

The maximum recommended weight allowance is 45.4 kg / 100 lb for top surface.
Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys
placed on the furnishing may encourage a child to climb on the furnishing and as a result may tip over onto the child.
NEVER allow children to climb or play with the TV or furnishing supporting the TV.
NEVER place toys, food, remote, etc. on top of the TV or TV furnishing.
ALWAY use either the safety hardware as instructed or other wall anchoring device.
Relocating audio and/or video equipment to furniture not specifically designed to support audio and/or video equipment
may result in death or serious injury due to furniture collapse or over turning onto a child.
NEVER place a TV on furniture that is not intended to support a TV.
NEVER exceed the maximum size and weight of the TV shown in the instructions.
Be sure to refer to the TV warning label as shown in the instructions.
Overloading drawers and shelves may result in furniture that can break or sag, or tip-over which may result in injury.
NEVER exceed the weight limits shown in the instructions.
Place the heavier items on lower shelves as far back from the front as possible.
Load the bottom surfaces first to avoid top-heavy furniture.
Moving furniture that is not designed to be moved or equipped with casters may result in injury or damage to furnishings or
personal property.
ALWAY unload shelves and drawers, starting with the top surfaces, before moving.
NEVER push or pull furniture on carpet. Have a friend help lift properly to move and/or reposition it.
The unit is not meant as a seat and no one should be sitting or standing on the top panel.
Questions? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPC number ready when calling.