Threshold STUDIO McGEE Bountiful TGT32CB User manual

>> Assembly instructions
TM
© 2021 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
Bountiful Wood & Glass 2 Door Cabinet
Style # TGT32CB
DPC-item #: 249-17-2197

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time.
Good luck – though we’re confident you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a work surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
tools needed (only hex wrench included)
Phillips head
screwdriver
For tipping restraint hardware kit only.
Power drill
Hex wrench

hardware
(H1) x 4
cam lock
(H2) x 4
cam bolt
(H3) x 8
M8 x 30 mm
wood dowel
(H4) x 16
M4 x 12 mm bolt
(H5) x 4
1/4” x 3/4” bolt
(H6) x 4
lock washer
(H7) x 4
flat washer
(H8) x 2
M4 x 25 mm
knob bolt
(H12) x 4
shelf support
(H10) x 4
door hinge
(H11) x 2
door catch
(H15) x 1
small hex wrench
(H9) x 2
knob
3
(H13) x 16
M3.5 x 12 mm screw
(H14) x 16
M3.5 x 15 mm
washer head screw

hardware
Spare hardware
(H17) x 1
tipping restraint hardware kit
(inside plastic bag)
4
(H16) x 1
large hex wrench

ITEM DESCRIPTION QTY
ATop panel 1
BBack panel 1
CLeft side frame 1
DRight side frame 1
ELeft door 1
FRight door 1
GShelf 1
HBottom panel 1
C
H
G
E
B
A
D
exploded diagram
F
5

how to use the cam lock system
1. 2. 3.
4. 5.
1. 2. 3.
Screw cam bolt into panel Push cam into panel - arrow
feature on cam top points to
panel edge
Align cam bolt(s) with cam(s)
and insert all the way into
cross-bored hole(s)
Rotate cam(s) clockwise
190°-230° to lock panels
together
Panels should be tight against
each other and connection
should be rigid
190°-230°
6

1.1. Securely screw the cam bolts (H2) into the designated small holes on the side frames (C and D).
step 1: prepare the side frames assembly
(H2) x 4
cam bolt
H2
7
H2
H2
H2
C
D

(H13) x 4
M3.5 x 12 mm screw
A
H13
The magnet faces forward
step 2: attach the door catches to the top panel
2.1. Using the pilot holes as a guide, attach two door catches (H11) to the top panel (A) as shown, with two 12 mm screws (H13) per door catch.
8
(H11) x 2
door catch
H11

step 3: attach the bottom panel between the side frames
3.1. Insert four wood dowels (H3) into the inner holes of bottom panel (H) at both ends.
3.2. Align and attach the bottom panel (H) between the side frames (C and D) by engaging four cam locks (H1).
H3
H3
9
(H3) x 4
M8 x 30 mm wood dowel
(H1) x 4
cam lock
C
D
H
Pilot holes for door hinge
The molding is located at front and will face
the floor when the unit is turned upright.
H1
H1
H3
H1
C
D
H
H1
H1

step 4: attach the top panel to both side frames
4.1. Insert four wood dowels (H3) into the top holes drilled on the posts of both side frames (C and D).
4.2. Orient and align the corner holes underneath the top panel (A) with the inserted wood dowels on the side frames (C and D).
4.3 Insert the 3/4’’ bolts (H5) with lock washers (H6) and flat washers (H7) through the metal tabs on both side frames (C and D) and screw into the threaded
inserts on the top panel( A).
10
(H3) x 4
M8 x 30 mm wood dowel
(H5) x 4
1/4” x 3/4” bolt
(H6) x 4
lock washer
(H7) x 4
flat washer
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
(H16) x 1
large hex wrench
A
A
C
D
H
C
D
H5
H6
H7
Door catch
H3

step 5: attach the back panel to the unit
B
CAUTION: Heavy! You may
need assistance with this step.
(H14) x 16
M3.5 x 15 mm
washer head screw
5.1. Now, go back and tighten all cam locks and screws. Make sure all the parts are tight and there are no gaps between the parts. This will help keep the unit
square.
5.2. Unfold the back panel (B) and position it onto the back edges of the assembly. Make sure that the overlaps on the panels are even all the way around.
Secure the back panel (B) in place with the washer head screws (H14), using the pilot holes as a guide.
NOTE: DO NOT use power tools. We recommend attaching back panel with the screws at the corners first.
Adhesive tape faces outward
11
B
H14
H14
H14
H14
H14
H14

step 6: install the door hinges
6.1. Unfold one door hinge and attach the door leaf to the top portion of left door (E) with four 12mm bolts (H4).
6.2. Repeat the some procedure to install the remaining door hinges (H10) to the doors (E and F).
(H4) x 16
M4 x 12 mm bolt
(H10) x 4
door hinge
H4
H10
(H15) x 1
small hex wrench
F
E
H4
12
Drainage hole
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
H4
H4
E
F

step 7: install the doors and knobs
7.1. Ask for assistance to lift the assembled unit upright and position it near the final location.
7.2. Using the pilot holes as a guide, attach the left door (E) to the left side frame (C) with three 12mm screws(H13) per frame leaf.
7.3. Fasten one knob (H9) to the front side of the left door (E) with one 25 mm bolt (H8).
7.4. Repeat the same process with the right door (F).
(H13) x 12
M3.5 x 12 mm screw
(H9) x 2
knob
CAUTION: Heavy! You may
need assistance with this step.
H8
H13
F
C
Drainage holes face downward
(H8) x 2
M4 x 25 mm knob bolt
D
E
EF
H9
13

8.1. Open the doors and insert four shelf supports (H12) into the holes pre-drilled on the side frame posts.
8.2. Tilt and rest the shelf (G) onto the shelf supports (H12).
step 8: install the shelf
(H12) x 4
shelf support
G
H12
14
H12
G

H13
H11
step 9: correct the doors alignment
NOTE: Open and close the doors and adjust the gaps to make sure they are aligned and shut correctly.
If you find that the doors do not close properly or do not align correctly, please follow these steps:
9.1. Adjust the floor levelers pre-attached underneath the side frames (C and D) to level the doors.
9.2. The door catches (H11) can be adjusted to ensure that the doors function properly. This can be done by moving the catches forward and back.
9.3. Open the doors and loosen the installed screws (H13) on the door hinges (H10) and adjust properly for a good fit.
9.4. Once the doors function properly, go back and tighten all the screws.
A
Floor leveler
CD
15
H13
H10

step 10: install the tipping restraint hardware kit
10.1. Adjust the pre-attached floor levelers to level the unit against a wall.
10.2. Follow the instructions printed on plastic bag containing tipping restraint hardware to attach tip-over restraint between the unit and wall.
NOTE: You can share the back panel screw hole for the anti-tipping hardware. You must use this tipping restraint to attach this unit to the wall, to prevent
accidents and/or injures.
Nylon strap
Tools required: Phillips screwdriver, stud finder, tape measure, pencil, power drill and 1/8” drill bit (not provided).
Metal bracket
Short screw
Wooden stud
Wall
Wall
Long screw
H17
(H17) x 1
tipping restraint hardware kit
(inside plastic bag)
Floor leveler
16

Care and Maintenance
• Use a soft, clean cloth that will not scratch the surface when dusting.
• Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
• Using solvents of any kind on your furniture may damage the finish.
• Never use water to clean your furniture as it may cause damage to the finish.
• Always use coasters under beverage glasses and flowerpots.
• Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill gently. Avoid rubbing.
• Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create spotting within the furniture finish.
• Stains or marks from crayons or ink markers will be difficult to remove.
• In the event that your furniture is stained or otherwise damaged during use, we recommend that you call a professional to repair your furniture.
• Check bolts/screws and nuts periodically and tighten them if necessary.
Further Advice about Wood Furniture Care
It is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity changes can cause fading, warping, shrinking and
splitting of wood. It is advised to keep furniture away from direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful tips will enhance your furniture as it ages.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace it for up to one (1) year from date of purchase.
Every Whalen Furniture product is designed to meet your highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province.
Customer Service: 1-855-MYTGTHOME (855-698-4846)
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenfurniture.com
17

M AX I M U M R E C O M M E N D E D W E I G H T L O A D S
MAXIMUM LOAD 22.7 kg / 50 lb
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Bountiful Wood & Glass 2 Door Cabinet
MODEL # TGT32CB
THIS UNIT IS INTENDED ONLY FOR USE WITHIN THE MAXIMUM WEIGHTS INDICATED. USE
WITH LOADS HEAVIER THAN THE MAXIMUM WEIGHTS INDICATED MAY RESULT IN INSTABILITY, CAUSING POSSIBLE
INJURY.
18

The maximum recommended weight allowance is 22.7 kg / 50 lb for top surface, shelf and bottom panel.
Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys
placed on the furnishing may encourage a child to climb on the furnishing and as a result may tip over onto the child.
NEVER allow children to climb or play with the TV or furnishing supporting the TV.
NEVER place toys, food, remote, etc. on top of the TV or TV furnishing.
ALWAYS use either the safety hardware as instructed or other wall anchoring device.
Relocating audio and/or video equipment to furniture not specifically designed to support audio and/or video equipment
may result in death or serious injury due to furniture collapse or over turning onto a child.
NEVER place a TV on furniture that is not intended to support a TV.
NEVER exceed the maximum size and weight of the TV shown in the instructions.
Be sure to refer to the TV warning label as shown in the instructions.
Overloading drawers and shelves may result in furniture that can break or sag, or tip-over which may result in injury.
NEVER exceed the weight limits shown in the instructions.
Place the heavier items on lower shelves as far back from the front as possible.
Load the bottom surfaces first to avoid top-heavy furniture.
Moving furniture that is not designed to be moved or equipped with casters may result in injury or damage to furnishings or
personal property.
ALWAYS unload shelves and drawers, starting with the top surfaces, before moving.
NEVER push or pull furniture on carpet. Have a friend help lift properly to move and/or reposition it.
DO NOT use this unit as a seating surface.

Questions? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.
FURNITURE TIPPING RESTRAINT
YOUNG CHILDREN MAY BE INJURED BY TIPPING FURNITURE AND YOU MUST USE THIS TIPPING
RESTRAINT TO ATTACH THIS UNIT TO THE WALL, TO PREVENT ACCIDENTS AND/OR INJURIES.
TO PROVIDE PROTECTION AGAINST THE UNEXPECTED TIPPING OF
FURNITURE DUE TO IMPROPER USE.
USE OF TIP-OVER RESTRAINTS MAY ONLY REDUCE, BUT NOT ELIMINATE, THE RISK OF TIP-OVER.
20
⚫ Unit must be placed on a level surface or leveled with included hardware (when applicable).
⚫ Do not sit or stand on or allow children to climb, sit or stand on the assembled product.
⚫ For safety reasons, it is imperative that this unit be mounted to the wall.
⚫ Do not use without installing the tip restraint.
⚫ Unit can tip over causing severe injury or death.
⚫ Do not exceed the recommended weight limits.
⚫ Evenly distribute the weight on each level and always keep the heavier loads on the bottom.
⚫ Before cutting, drilling or hammering into any wall or floor surface, verify the location of electrical,
plumbing and gas lines. Cutting may cause serious injury.
WARNING