Threshold STUDIO MCGEE Kennington TGT66BK User manual

>> Assembly instructions
TM
© 2023 Target. The Bullseye Design is a trademark of Target Brands, nc. All rights reserved.
Kennington 2 Door Display Cabinet
Style # TGT66BK
DPC-item #: 249-17-3176

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time.
Good luck – though we’re confident you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a work surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
tools needed (not included)
Phillips head
screwdriver
For tipping restraint hardware kit only.
power drill

hardware
3
(H1) x 20
cam lock
(H2) x 20
cam bolt
(H3) x 16
M8 x 30 mm
wood dowel
(H4) x 26
M3.5 x 15 mm
washer head screw
(H6) x 2
roller catch
(H ) x
shelf support
(H13) x 2
tipping restraint hardware kit
(inside plastic bag)
(H10) x 24
M3.5 x 15 mm zinc screw
(H12) x
cam lock cover
(H9) x 6
hinge
(H7) x 2
roller catch metal plate
(H5) x 16
M3.5 x 12 mm pan head screw
Spare hardware (H11) x 4
3/16” x 35 mm
handle bolt

TEM DESCR PT ON QTY
A Top panel 1
B Base 1
C Back panel 1
D Left side panel 1
E Right side panel 1
F Top rear stretcher 1
G Top front stretcher 1
H Fixed shelf 1
Adjustable shelf 2
J Left door 1
K Right door 1
L Handle 2
exploded diagram
A
B
C
D
E
F
G
H
J
L
K
4
L

how to use the cam lock system
1. 2. 3.
4. 5.
1. 2. 3.
Screw cam bolt into panel Push cam into panel - arrow
feature on cam top points to
panel edge
Align cam bolt(s) with cam(s)
and insert all the way into
cross-bored hole(s)
Rotate cam(s) clockwise
190°-230° to lock panels
together
Panels should be tight against
each other and connection
should be rigid
190°-230°
5

1.1. Use the pilot holes as a guide, fasten two roller catch metal plates (H7) to the base (B) with two 12 mm screws (H5) per plate. Make sure that the projection
on each roller catch strike plate points towards the back of the unit.
step 1: attach the roller catch plates
(H7) x 2
roller catch metal plate
(H5) x 4
M3.5 x 12 mm
pan head screw B
H5
H5
H7
H7
NOTE: DO NOT use power tools.
6
The projection faces backward

step 2: prepare the top panel and base assembly
(H2) x 12
cam bolt
2.1. Securely screw the cam bolts (H2) into the designated small holes on the top panel (A) and the base (B).
A
B
H2
H2
H2
H2
H2
H2
H2
H2
H2
H2
H2
H2
7

step 3: prepare the side panels assembly
(H2) x
cam bolt
3.1. Securely screw the cam bolts (H2) into the designated small holes on the side panels (D and E).
D
E
H2
H2
H2
H2
H2
H2
H2
H2
8

step 4: attach the stretchers and fixed shelf
4.1. nsert four 30 mm wood dowels (H3) into the inner holes of the fixed shelf (H) at both ends.
4.2. Align and attach the fixed shelf (H) to the left side panel (D) by engaging two cam locks (H1).
4.3. Orient and attach the top stretchers (F and G) to the left side panel (D) with two cam locks (H1).
4.4. Repeat the same process to attach the right side panel (E) at the opposite end,
(H1) x
cam lock
(H3) x 4
M8 x 30 mm
wood dowel
D
E
F
G
H
H3
H
H1
D E
9
The shelf molding faces the base and is located at front of the unit
The cam lock housings point towards the
back of the unit and are located at the bottom

step 5: attach the base to the side panels
5.1. nsert four 30 mm wood dowels (H3) into the bottom inner holes of the side panels (D and E).
5.2. Orient and attach the base (B) to the side panels (D and E) using four cam locks (H1).
(H1) x 4
cam lock
(H3) x 4
M8 x 30 mm
wood dowel
D
E
B
B
D E
H3
H1
10
The back edges are flush with each other
Floor leveler

step 6: attach the top panel to the previous assembly
6.1. nsert eight 30 mm wood dowels (H3) into the top inner holes of both side panels (D and E) and top stretchers (F and G).
6.2. Align the large holes on the top panel (A) with the inserted wood dowels and press them together.
6.3. Attach the top panel (A) into place by engaging eight cam locks (H1).
(H1) x
cam lock
(H3) x
M8 x 30 mm
wood dowel
D
E
A
A
F
G
F G D E
H1
H3
11
The pilot holes face backward

step 7: attach the back panel
The adhesive tape faces outward.
7.1. Now, go back and tighten all cam locks and screws. Make sure that the previous all the parts are tight and there are no gaps between the parts. This will help
keep the unit square.
7.2. Unfold the back panel (C) and align the predrilled holes with the pilot holes on the back of top panel (A). Attach the back panel (C) into place with the 15 mm
washer head screws (H4) provided.
NOTE: We recommend attaching back panel with the screws at corners first.
CAUTION: Heavy! You may
need assistance with this step.
(H4) x 26
M3.5 x 15 mm
washer head screw
C
C
C
H4 H4
12

step : install the roller catches
8.1. Using the pilot holes as a guide, orient and attach one roller catch (H6) to each door (J and K) with two 12 mm screws (H5).
(H5) x 4
M3.5 x 12 mm
pan head screw
(H6) x 2
roller catch
H5
H5
H6
J
K
13
The roller runs against the bottom edge
NOTE: DO NOT use power tools.

step 9: install the door hinges
9.1. Extend three hinges (H9) and rest the hinge cups onto the cutouts of each door (J and K).
9.2. With the pilot holes as a guide, fasten the door hinges (H9) into place by using two 15 mm zinc screws (H10) in each hinge.
J
K
H9
H9
H9
H9
H9
H9
14
NOTE: DO NOT use power tools.
(H10) x 12
M3.5 x 15 mm zinc screw
(H9) x 6
hinge
H10
H10
H10
H10
H10
H10

step 10: install the door handles
10.1. Attach one handle (L) to the front of each door (J and K) with two 35 mm handle bolts (H11).
NOTE: DO NOT use power tools.
(H11) x 4
3/16” x 35 mm handle bolt
L
L
H11
H11
H11
H11
J
K
15

step 11: attach the doors
11.1. Ask for assistance to lift the assembled unit upright and position it near the final location.
11.2. Pick up the left door (J) and attach the extended hinge bases to the left side panel (D) with six 15 mm zinc screws (H10), using the pilot holes as a guide.
Make sure that both door hinges engage and function properly.
11.3. Repeat the same process to attach the right door (K) into place.
11.4. Open and close the doors to make sure they are aligned and shut correctly. f necessary, adjust the screws for a good fit. Refer to the hinge sticker on door
for adjustment.
CAUTION: Heavy! You may
need assistance with this step.
f you find that the doors need to be adjusted slightly, turn
the appropriate screw, as illustrated upper.
1. TO ADJUST THE DOOR FORWARD OR BACKWARD.
2. TO ADJUST THE DOOR TO R GHT OR TO LEFT.
3. TO ADJUST THE DOOR UP OR DOWN
D
E
J
K
H9
D
E
J K
12
3
(H10) x 12
M3.5 x 15 mm zinc screw
H10
16

H8
H12
H8
step 12: attach the adjustable shelves and put cam lock covers
(H ) x
shelf support
(H12) x
cam lock cover
12.1. Open the doors and insert eight shelf supports (H8) in the holes on the side panels (D and E) at the desired height. Be sure to place the four shelf supports
at the same level to level the shelf.
12.2. Tilt and rest the adjustable shelves ( ) onto the shelf supports. Secure the shelves into place with the 12 mm screws (H5) for extra support.
12.3. Plug the cam lock covers (H12) onto the visible cam locks to conceal the cams.
(H5) x
M3.5 x 12 mm pan head screw
H5
17
D
E

step 13: correct the doors alignment
Floor leveler
H6
H7
H7
B
J
K
B
J K
B
18
f you find that the doors need to be adjusted slightly, turn
the appropriate screw, as illustrated upper.
1. TO ADJUST THE DOOR FORWARD OR BACKWARD.
2. TO ADJUST THE DOOR TO R GHT OR TO LEFT.
3. TO ADJUST THE DOOR UP OR DOWN
12
3
NOTE: The roller catch (H6) and roller catch metal plate (H7) have elongated mounting holes that allow for adjustment. Open and close the doors and adjust
the gaps to make sure they are aligned correctly and the roller snaps onto the front projection of the metal plate (H7) properly.
f you find that the doors do not close properly or do not align correctly, please follow these steps:
13.1. Adjust the European hinges and floor levelers pre-attached underneath the base (B) to correct tilting and level the doors.
13.2. The roller catch metal plates (H7) can be adjusted to ensure that the doors function properly. This can be done by moving the metal plates forward and back.
13.3. Open the doors and loosen the installed screws on the roller catches (H6) and adjust properly for a good fit.
13.4. Once the doors function properly, go back and tighten all the screws.

step 14: install the tipping restraint hardware kit
14.1. Follow the instructions printed on plastic bag containing tipping restraint hardware to attach tip-over restraint between the unit and wall.
NOTE: You can share the back panel screw hole for the anti-tipping hardware. You must use this tipping restraint to attach this unit to the wall, to prevent
accidents and/or injures.
Tools required: Phillips screwdriver, stud finder, tape measure, pencil, power drill and 1/8” drill bit (not provided).
Wooden stud
Wall
Metal bracket
Nylon strap Short screw
Wall
Long screw
H13
(H13) x 2
tipping restraint hardware kit
(inside plastic bag)
19

FURNITURE TIPPING RESTRAINT
YOUNG CH LDREN MAY BE NJURED BY T PP NG FURN TURE AND YOU MUST USE TH S T PP NG
RESTRA NT TO ATTACH TH S UN T TO THE WALL, TO PREVENT ACC DENTS AND/OR NJUR ES.
TO PROV DE PROTECT ON AGA NST THE UNEXPECTED T PP NG OF
FURN TURE DUE TO MPROPER USE.
USE OF T P-OVER RESTRA NTS MAY ONLY REDUCE, BUT NOT EL M NATE, THE R SK OF T P-OVER.
WARNING
 Unit must be placed on a level surface or leveled with included hardware (when applicable).
 Do not sit or stand on or allow children to climb, sit or stand on the assembled product.
 For safety reasons, it is imperative that this unit be mounted to the wall.
 Do not use without installing the tip restraint.
 Unit can tip over causing severe injury or death.
 Do not exceed the recommended weight limits.
 Evenly distribute the weight on each level and always keep the heavier loads on the bottom.
 Before cutting, drilling or hammering into any wall or floor surface, verify the location of electrical,
plumbing and gas lines. Cutting may cause serious injury.
20