Threshold Studio McGee Promontory TGT72BK User manual

>> Assembly instructions
TM
© 2021 Target. The Bullseye Design is a trademark of Target Brands, nc. All rights reserved.
Promontory 72” Cabinet with Sliding Doors
Style # TGT72BK
DPC-item #: 249-17-0042

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time.
Good luck – though we’re confident you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a work surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
tools needed (not included)
phillips head
screwdriver
For tipping restraint hardware kit only.
power drill

hardware
(H1) x 16
cam lock
(H2) x 16
cam bolt
(H3) x 16
M8 x 30 mm
wood dowel
(H4) x 32
M3.5 x 15 mm
washer head screw
(H5) x 4
M4 x 35 mm
screw
(H6) x
shelf support
(H7) x
cam lock cover
Spare hardware
(H9) x 2
tipping restraint hardware
kit (inside plastic bag)
(H ) x
rubber bumper
3

TEM DESCR PT ON QTY
A Top panel 1
B Stretcher 1
C Fixed shelf 2
D Adjustable shelf 2
E Base 1
F Back panel 1
G Left side panel 1
H Right side panel 1
Left sliding door 1
J Right sliding door 1
exploded diagram
A
B
C
C
D
D
E
F
G
H
J
4

how to use the cam lock system
1. 2. 3.
4. 5.
1. 2. 3.
Screw cam bolt into panel Push cam into panel - arrow
feature on cam top points to
panel edge
Align cam bolt(s) with cam(s)
and insert all the way into
cross-bored hole(s)
Rotate cam(s) clockwise
190°-230° to lock panels
together
Panels should be tight against
each other and connection
should be rigid
190°-230°
5

1.1. Securely screw the cam bolts (H2) into the designated small holes on the side panels (G and H).
step 1: prepare side panels assembly
(H2) x
cam bolt
G
H
H2
H2
H2
H2
H2
H2
H2
H2
6

step 2: prepare top panel and the base assembly
2.1. Securely screw the cam bolts (H2) into the designated small holes on the top panel (A) and the base (E).
(H2) x
cam bolt
A
E
H2
H2
H2
H2
H2
H2
H2
H2
7

step 3: attach the stretcher to the top panel
(H5) x 4
M4 x 35 mm
screw
A
B
H5
H5
H5
3.1. Align and attach the stretcher (B) to the top panel (A) with four 35 mm screws (H5).
H5
NOTE: DO NOT use power tools.
8

step 4: attach fixed shelves between the side panels
4.1. nsert four 30 mm wood dowels (H3) into the inner side holes of each fixed shelf (C) at both ends.
4.2. Align and attach the fixed shelves between the side panels (G and H) with eight cam locks (H1).
(H1) x
cam lock
(H3) x
M8 x 30 mm
wood dowel
G
H
G
H1
H3
C
C
The moldings are located at front
and face the bottom of the unit.
9

step 5: attach the side panels to the base
5.1. nsert two 30 mm wood dowels (H3) into the bottom inner holes of each side panel (G and H).
5.2. Orient and attach the side panels (G and H) to the base (E) using four cam locks (H1).
(H1) x 4
cam lock
(H3) x 4
M8 x 30 mm
wood dowel
G
H
E
H1
H3
E
G
Floor leveler
The floor protectors and the back
edges point in the same direction.
10

step 6: attach the top panel to the side panels
Stretcher faces upward
(H1) x 4
cam lock
(H3) x 4
M8 x 30 mm
wood dowel
A
G
H
H1
H3
A G
6.1. nsert two 30 mm wood dowels (H3) into the top inner holes of each side panel (G and H).
6.2. Align and attach the top panel (A) to both side panels (G and H) using four cam locks (H1).
11

step 7: attach the back panel to the previous assembly
(H4) x 32
M3.5 x 15 mm
washer head screw
7.1. Now, go back and tighten all cam locks and screws. Make sure all the parts are tight and there are no gaps between the parts. This will help keep the unit
square.
7.2. Pick the back panel (F) and position it onto the back edges of the assembly, using the pilot holes on the back of the top panel (A) as a guide. Make sure that
the overlaps on the panels are even all the way around and the indentations align up with each other. Secure the back panel (F) in place with the washer
head screws (H4).
NOTE: We recommend attaching back panel with the screws at the corners first.
F
H4 H4
F
Adhesive tape faces outward
NOTE: DO NOT use power tools.
F
12

step : install the adjustable shelves
8.1. With the help of another adult, stand the unit upright.
8.2. nsert four shelf supports (H6) into the desired holes in the sides of each compartment. Make sure you place the four shelf supports in the same level so the
shelf is not tilted.
8.3. Tilt and rest the adjustable shelves (D) onto the shelf supports.
(H6) x
shelf support
D
D
D
H6
CAUTION: Heavy! You may
need assistance with this step.
13

1
2
step 9: install the sliding doors
9.1. Pick up one sliding door and rest the bottom sliding rollers onto the roller track on the base (E).
9.2. Reach inside to top of door and slide lever down to retract the guide pin.
NOTE: The lever has lip on top edge to pull it forward at the bottom of slot to lock the pin in place.
9.3. Line up guide pins with the top guideway and press lever to unlock guide pin and release into the track.
9.4. Repeat above steps to install the outer sliding door. You need slide inside door to one side to allow access to the other side of the outer door in opening to
access slide door lock and release the guide pin. Then slide inner door to opposite side to allow access to other side of outer door in the open case and
release the other guide pin.
CAUTION: Heavy! You may
need assistance with this step.
Guide pin
Lever
Sliding roller
Door inside
Door inside Door inside
J
E
A
Door inside
14

/
step 10: plug the cam lock covers and affix the rubber bumpers
10.1. Plug the cam lock covers (H7) into the visible cam locks to conceal the cams.
10.2. Take the pilot holes as a guide, affix four rubber bumpers (H8) onto each side panel (G and H) where the sliding doors are in contact with.
(H7) x
cam lock cover
(H ) x
rubber bumper
H7
H8
G
H
J
NOTE: DO NOT slam shut the sliding
doors to prevent from damaging and
leaving gap.
H
15

step 11: install the tipping restraint hardware kit
11.1. Adjust the pre-attached floor levelers to level the unit against a wall.
11.2. Follow the instructions printed on plastic bag containing tipping restraint hardware to attach tip-over restraint between the unit and wall.
NOTE: You can share the back panel screw hole for the anti-tipping hardware. You must use this tipping restraint to attach this unit to the wall, to prevent
accidents and/or injures.
Nylon strap
Tools required: Phillips screwdriver, stud finder, tape measure, pencil, power drill and 1/8” drill bit (not provided).
Metal bracket
Short screw
Wooden stud
Wall
Wall
Long screw
Floor leveler
(H9) x 2
tipping restraint hardware
kit (inside plastic bag)
H9
16

Care and Maintenance
 Use a soft, clean cloth that will not scratch the surface when dusting.
 Use of furniture polish is not necessary. Should you choose to use polish, test first in an inconspicuous area.
 Using solvents of any kind on your furniture may damage the finish.
 Never use water to clean your furniture as it may cause damage to the finish.
 Always use coasters under beverage glasses and flowerpots.
 Liquid spills should be removed immediately. Using a soft, clean cloth, blot the spill gently. Avoid rubbing.
 Always use protective pads under hot dishes and plates. Heat can cause chemical changes that may create spotting within the furniture finish.
 Stains or marks from crayons or ink markers will be difficult to remove.
 n the event that your furniture is stained or otherwise damaged during use, we recommend that you call a professional to repair your furniture.
 Check bolts/screws and nuts periodically and tighten them if necessary.
Further Advice about Wood Furniture Care
t is best to keep your furniture in a climate-controlled environment. Extreme temperature and humidity changes can cause fading, warping, shrinking and
splitting of wood. t is advised to keep furniture away from direct sunlight as sun may damage the finish.
Proper care and cleaning at home will extend the life of your purchase. Following these important and helpful tips will enhance your furniture as it ages.
We hope you enjoy your purchase for many years.
Thank you for your purchase!
QUALITY GUARANTEE
We are confident that you will be delighted with your Whalen Furniture purchase.
Should this product be defective in workmanship or materials or fail under normal use, we will repair or replace it for up to one (1) year from date of purchase.
Every Whalen Furniture product is designed to meet your highest expectations. We guarantee that you will immediately see the value of our fine furniture.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state or province to province.
Customer Service: 1-855-MYTGTHOME (855-698-4846)
8:30 a.m. - 4:30 p.m., PST, Monday to Friday
www.whalenfurniture.com
17

M AX I M U M R E C O M M E N D E D W E I G H T L O A D S
MAX MUM LOAD 22.7 kg / 50 lb
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Promontory 72” Cabinet with Sliding Doors
MODEL # TGT72BK
TH S UN T S NTENDED ONLY FOR USE W TH N THE MAX MUM WE GHTS ND CATED. USE
W TH LOADS HEAV ER THAN THE MAX MUM WE GHTS ND CATED MAY RESULT N NSTAB L TY, CAUS NG POSS BLE
NJURY.
18

The maximum recommended weight allowance is 22.7 kg / 50 lb for each shelf.
Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys
placed on the furnishing may encourage a child to climb on the furnishing and as a result may tip over onto the child.
NEVER allow children to climb or play with the TV or furnishing supporting the TV.
NEVER place toys, food, remote, etc. on top of the TV or TV furnishing.
ALWAYS use either the safety hardware as instructed or other wall anchoring device.
Relocating audio and/or video equipment to furniture not specifically designed to support audio and/or video equipment
may result in death or serious injury due to furniture collapse or over turning onto a child.
NEVER place a TV on furniture that is not intended to support a TV.
NEVER exceed the maximum size and weight of the TV shown in the instructions.
Be sure to refer to the TV warning label as shown in the instructions.
Overloading drawers and shelves may result in furniture that can break or sag, or tip-over which may result in injury.
NEVER exceed the weight limits shown in the instructions.
Place the heavier items on lower shelves as far back from the front as possible.
Load the bottom surfaces first to avoid top-heavy furniture.
Moving furniture that is not designed to be moved or equipped with casters may result in injury or damage to furnishings or
personal property.
ALWAYS unload shelves and drawers, starting with the top surfaces, before moving.
NEVER push or pull furniture on carpet. Have a friend help lift properly to move and/or reposition it.
DO NOT use the unit as a seating surface.
19

Questions? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPC number ready when calling.
FURNITURE TIPPING RESTRAINT
YOUNG CH LDREN MAY BE NJURED BY T PP NG FURN TURE AND YOU MUST USE TH S T PP NG
RESTRA NT TO ATTACH TH S UN T TO THE WALL, TO PREVENT ACC DENTS AND/OR NJUR ES.
TO PROV DE PROTECT ON AGA NST THE UNEXPECTED T PP NG OF
FURN TURE DUE TO MPROPER USE.
USE OF T P-OVER RESTRA NTS MAY ONLY REDUCE, BUT NOT EL M NATE, THE R SK OF T P-OVER.
WARNING
 Unit must be placed on a level surface or leveled with included hardware (when applicable).
 Do not sit or stand on or allow children to climb, sit or stand on the assembled product.
 For safety reasons, it is imperative that this unit be mounted to the wall.
 Do not use without installing the tip restraint.
 Unit can tip over causing severe injury or death.
 Do not exceed the recommended weight limits.
 Evenly distribute the weight on each level and always keep the heavier loads on the bottom.
 Before cutting, drilling or hammering into any wall or floor surface, verify the location of electrical,
plumbing and gas lines. Cutting may cause serious injury.