Threshold TGAVCL-13 User manual

>> Assembly instructions
TM
© 2020 Target. The Bullseye Design is a trademark of Target Brands, Inc. All rights reserved.
Media Console with Storage - Gray
Style # TGAVCL-13
DPC-item #: 249-10-0053

2
Congratulations on your latest Target purchase.
Now what? Don’t start sweating over this box of parts. This will be easy. We did the hard work for you.
All you need to do is follow our simple instructions and you’ll be on your way to transforming your room in no time.
Good luck – though we’re confident you won’t need it.
before you begin
1. Check for damaged or missing parts. Call 1-855-MYTGTHOME (855-698-4846) to order missing supplies.
2. Use the carton as a work surface to prevent product damage during assembly.
3. Gather all tools prior to assembly.
tools needed (only hex wrench included)
For tipping restraint hardware kit only.
Phillips head
screwdriver
Hex wrench

3
Questions? Just call 1-855-MYTGTHOME (855-698-4846) for parts and service. For faster service, have the style number and DPCI number ready when calling.
Children have died from furniture tip-over.
To reduce the risk of furniture tip-over:
⚫ ALWAYS install tip-over restraint provided.
⚫ FOR use with televisions weighing 135 lbs /
61.2 kg or less. Use with heavier televisions
may result in instability causing tip-over resulting
in death or serious injury.
⚫ NEVER allow children to stand, climb or hang
on drawers, doors, or shelves.
⚫ NEVER open more than one drawer at a time.
⚫ Place heaviest items in the lowest drawers.
Use of tip-over restraints may only reduce,
but not eliminate, the risk of tip-over.
WARNING

M AX I M U M R E C O M M E N D E D W E I G H T L O A D S
4
MANUFACTURER: Whalen Furniture Manufacturing
CATALOG: Media Console with Storage - Gray
MODEL # TGAVCL-13
FOR USE WITH TELEVISIONS WEIGHING 80 LBS (36.3 KG) OR LESS. USE WITH HEAVIER TELEVISIONS MAY RESULT IN
INSTABILITY CAUSING TIP OVER RESULTING IN DEATH OR SERIOUS INJURY.
FITS UP TO MOST 139.7 cm / 55 in.
DIAGONAL FLAT-PANEL TVs
MAXIMUM LOAD 36.3 kg / 80 lb.
MAXIMUM LOAD 22.7 kg / 50 lb.

hardware
5
(H1) x 8
cam lock
(H2) x 8
cam bolt
(H3) x 16
M8 x 30 mm
wood dowel
(H4) x 8
1/4” x 5/8” bolt
(H5) x 8
lock washer
(H6) x 8
flat washer
(H7) x 8
M4 x 50 mm screw
(H8) x 12
M4 x 32 mm screw
(H10) x 12
M3.5 x 12 mm screw
(H11) x 12
shelf support
(H14) x 4
door hinge
(H15) x 8
cam lock cover
(H12) x 4+1
rubber bumper
(H16) x 2
handle (H17) x 4
25 mm handle bolt
(H13) x 1
hex wrench
(H9) x 24
M3.5 x 15 mm
washer head screw

hardware
Spare hardware
(H18) x 2
tipping restraint hardware kit
(inside plastic bag)
6

ITEM DESCRIPTION QTY
ATop panel 1
BBack panel 1
CLeft side panel 1
DRight side panel 1
ELeft partition panel 1
FRight partition panel 1
GLeft door 1
HRight door 1
IBottom panel 1
JSupport leg with leveler 2
KBottom stretcher 2
LLarge adjustable shelf 1
MSmall adjustable shelf 2
exploded diagram
7
C
M
K
J
I
H
G
F
E
B
A
D
L
K
M
J

KRZWRXVHWKHFDPORFNV\VWHP
  
 
  
6FUHZFDPEROWLQWRSDQHO 3XVKFDPLQWRSDQHO-DUURZ
IHDWXUHRQFDPWRSSRLQWVWR
SDQHOHGJH
$OLJQFDPEROWVZLWKFDPV
DQGLQVHUWDOOWKHZD\LQWR
FURVV-ERUHGKROHV
5RWDWHFDPVFORFNZLVH
-WRORFNSDQHOV
WRJHWKHU
3DQHOVVKRXOGEHWLJKWDJDLQVW
HDFKRWKHUDQGFRQQHFWLRQ
VKRXOGEHULJLG
190°-230°


step 1: Combine the base
1.1. Attach the bottom stretchers (K) between the support legs with levelers (J), using the 5/8” bolts (H4) with the washers (H5 and H6) through the metal
brackets and screw into place.
(H4) x 8
1/4” x 5/8” bolt
(H5) x 8
lock washer
(H6) x 8
flat washer
(H13) x 1
hex wrench
NOTE: DO NOT fully tighten all bolts
until you finish assembling all parts.
Once assembled, go back and fully
tighten all bolts. This will make the
assembly easier.
9
J
K
J
K
J
K
H4
H5
H6
H4H5H6

step 2: Screw-in cam bolts on the top panel
2.1. Securely screw the cam bolts (H2) into the designated small holes on the top panel (A).
10
(H2) x 8
cam bolt
A
H2
H2
H2
H2
H2
H2
H2
H2

step 3. Attach side panels and partition panels to the top panel
3.1. Insert two wood dowels (H3) into the top inner holes of each side panels (C and D) and partition panels (E and F).
3.2. Secure both side panels (C and D) and partition panels (E and F) to the top panel (A) using eight cam locks (H1).
(H1) x 8
cam lock
(H3) x 8
M8 x 30 mm wood dowel
C
F
E
D
CDEF
A
A
Finished edge
Finished edge
H1
H3
11

step 4. Attach bottom panel to the vertical panels
4.1. Insert two wood dowels (H3) into the bottom inner holes of each side panels (C and D) and partition panels (E and F).
4.2. Align and attach the bottom panel (I) to the four vertical panels (C, D, E and F) as shown, using eight 50 m screws (H7).
(H3) x 8
M8 x 30 mm wood dowel
(H7) x 8
M4 x 50 mm screw
H3
H3
H3
H3
H7
H7
H7
H7
I
C
F
E
D
The edge with the mounting holes for metal
base running against located at back.
Door hinge mounting holes
12

step 5. Attach the base to the bottom panel
5.1. Ask for assistance to turn the unit upside down.
5.2. Align the mounting holes on the assembled base (J and K) with the pilot holes on the bottom panel (I). Attach using twelve 32 mm screws (H8) provided.
(H8) x 12
M4 x 32 mm screw
H8
H8
H8
H8
H8
J
K
K
J
I
CAUTION: Heavy! You may
need assistance with this step.
13

step 6. Attach the back panel to the frame
6.1. With the help of another adult, flip the assembled unit around on its front edges.
6.2. Align the back panel (B) with the pilot holes on the assembly as shown. Make sure that the overlaps on the panels are even all the way around.
6.3. Attach the back panel (B) into place using the washer head screws (H9) provided.
NOTE: we recommend attaching back panel with the screws at the corners first.
B
H9
B
CAUTION: Heavy! You may
need assistance with this step.
(H9) x 24
M3.5 x 15 mm
washer head screw
14

step 7. Attach hinges to the doors
7.1. Extend the hinges if necessary and rest the hinge cups (H14) onto the cutouts of the doors (G and H).
7.2. With the pilot holes as a guide, secure the door hinges (H14) into place by tightening the screws provided .
(H14) x 4
door hinge
H14
H14
H
G
15
H14
H14

step 8. Fasten the handles to the doors
8.1. Attach one handle (H16) to the front side of each doors (G and H) using the handle bolts (H17) provided.
(H16) x 2
handle (H17) x 4
25 mm handle bolt
H16
H16
H17
H17
H
G
16

1
3
2
step 9. Install doors
9.1. With the help of another adult, lift the unit upright and position it near the desired location.
9.2. Pick up the left door (G) and attach the two assembled door hinges (H14) to the left side panel (C) properly.
9.3. Repeat the same process to attach the right door (H) to the right side panel (D). Open and close the doors to make sure they are aligned and shut correctly.
If necessary, adjust the screws on the hinge arms for better fit.
If you find that the doors need to be adjusted slightly, turn
the appropriate screw, as illustrated upper.
1. TO ADJUST THE DOOR FORWARD OR BACKWARD.
2. TO ADJUST THE DOOR TO RIGHT OR TO LEFT.
3. TO ADJUST THE DOOR UP OR DOWN
C
G
H
D
H14
CAUTION: Heavy! You may
need assistance with this step.
17

step 10. Install the adjustable shelves
10.1. Insert four shelf supports (H11) into the desired holes in the sides of each compartment. Make sure you place the four shelf supports in the same level so
the shelf is not tilted.
10.2. Tilt and rest the adjustable shelves (L and M) onto the shelf supports (H11) and secure them into place using the 12 mm screws (H10).
(H10) x 12
M3.5 x 12 mm screw
(H11) x 12
shelf support M
L
M
H10
H11
H11
18

step 11. Install rubber bumpers and conceal the cams
11.1. Put two rubber bumpers (12) onto the front edge of each partition panels (E and F).
11.2. Plug the cam lock covers (H15) onto the visible cams locks to conceal the cams.
(H15) x 8
cam lock cover
H15
H12 H12
(H12) x 4
rubber bumper
F
E
19
F
E

step 12. Install the tip-over restraint hardware kits
12.1. Adjust the pre-attached floor levelers to level the unit against a wall.
12.2. Follow the instructions printed on plastic bag containing tipping restraint hardware (H18) to attach tip-over restraint between the unit and wall.
NOTE: You must use this tipping restraint to attach this unit to the wall, to prevent accidents and/or injures.
Nylon strap
Tools required: Phillips screwdriver, stud finder, tape measure, pencil, power drill and 1/8” drill bit (not provided).
Metal bracket
Short screw
Wooden stud
Wall
Wall
Long screw
(H18) x 2
tipping restraint hardware kit
(inside plastic bag)
Floor leveler
H18
20