Titan Fitness PT 1690 User manual

MPN: PT1690
SKU: 400610
UPC: 765857422800
PT 1690
POWER TOWER
Dip Stand
Main Stand
Pull-Up Bar
Upright
Foam Tube Upright
Foam Grip
Cross Bar
Endcap
Spacer Tube
Caution
Label
Foam Grip
Left Push-Up Bar
Right Push-Up Bar
Foam Pad
Dip Stand

2
2
2
1
1
2
4
2
1
2
1
4
QTY
DIAGRAM NO.
1
4
8
3
7
2
6
5
12
11
10
9
DESCRIPTION
Main Stand
Upright
Pull-up Bar
Cross Bar
Dip Stand
Left Push-up Bar
Right Push-up Bar
Foot Stand
Foam Grip
Foam Pad
Spacer Tube
Connective Cap
PART NUMBER (PN)
P400610-1
P400610-2
P400610-3
P400610-4
P400610-5
P400610-6
P400610-7
P400610-8
P400610-9
P400610-10
P400610-11
P400610-12
13
14
15
16
17
18
19
20
21
22
23
24
26
27
28
29
25 P400610-25
P400610-26
P400610-27
P400610-28
P400610-29
P400610-13
P400610-14
P400610-15
P400610-16
P400610-17
P400610-18
P400610-19
P400610-20
P400610-21
P400610-22
P400610-23
P400610-24
Foam Tube ø22*ø32x265
Long Foam Tube ø22*ø32x350
End Cap (38.1mm)
Round Plug (25.4mm)
Round Plug (38.1mm)
Screw, Flat Head M5*.8*15
Bolt, Hex Head M6*1*45
Bolt, Hex Head M8*1.25*50
Bolt, Hex Head M10*1.5*130
Nylon Lock Nut M6*1
Nylon Lock Nut M10*1.5
Arc Washer M6
Arc Washer M8
Arch Washer M10
Wrench
Manual
Caution Label
2
1
8
2
2
4
8
6
2
2
4
8
1
2
2
16
1
PT 1690
PARTS LIST

Illustration is used to help identify the hardware used for assembly. Place the washers or the ends of the
bolts or screws on the circles to check for the correct diameter. Use the small scale to check the length
of the bolts and screws.
NOTICE: The length of all bolts and screws, except those with flat
heads, is measured from below the head to the end of the bolt
or screw. Flat head bolts and screws are measured from the
top of the head to the end of the bolt or screw.
length
length
HARDWARE IDENTIFICATION CHART
mm.
in.
INCHES
MILLIMETERS
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1/2 1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6
6 8 10 12
3/16" 1/4" 5/16" 3/8" 1/2"
Part Illustration Qty
P400610-19 Bolt, Hex Head M6*1*45 4
P400610-20 Bolt, Hex Head M8*1.25*50 2
P400610-24 Arc Washer M6 8
P400610-25 Arc Washer M8 2
P400610-26 Arch Washer M10 16
After unpacking the unit, open the hardware bag and make sure that you have all the following items.
Some hardware may be already attached to the part.
P400610-21 Bolt, Hex Head M10*1.5*130 8
P400610-22 Nylon Lock Nut M6*1 4
P400610-23 Nylon Lock Nut M10*1.5 8
Diagram # Description

PT 1690
PARTS
DRAWING
BEFORE BEGINNING THIS OR ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR PERSONS OVER THE AGE
OF THIRTY-FIVE OR WITH PREEXISTING HEALTH PROBLEMS. Make sure all
nuts and bolts are securely tightened, and follow all safety tips and instructions set
forth herein. This product should not be used by persons weighing more than 250 lbs.
unless otherwise stated in the front of your manual.
Keep others including children & pets away from equipment when in use.
Failure to comply with these warnings could result
in bodily injury and property damage. All warnings
and instructions are to be read prior to use. Replace
this warning label if damaged, illegible, or removed.
Label is larger than illustration size

STEP 1
Bolt the MAIN STAND(1), CROSS BAR(4), and DIP STAND(5) together with HEX BOLTS (M10x1.5x130mm)(21),
ARC WASHERS(M10)(26), and NYLOCK NUTS(M10x1.5)(23). Repeat on other side.
STEP 2
There is an “L” decal on the LEFT PUSH-UP BAR(6), and an “R” decal on the RIGHT PUSH-UP
BAR(7). Insert the LEFT PUSH-UP BAR(6) into the DIP STAND(5) on the left side and secure with HEX
BOLTS(M6x1x45mm)(19), ARC WASHERS(M6)(24), and NYLOCK NUTS(M6x1)(22). Repeat on the
right side.
R
L
LEFT
RIGHT

STEP 3
Insert the two UPRIGHTS(2) onto the MAIN STANDS(1). Place a ARC WASHER(M10)(26) onto a
HEX BOLT(M10x1.5x130mm)(21). Slide a SPACER TUBE(11) between the UPRIGHT(2) and the DIP
STAND(5), then insert the bolt through all these tubes and bolt them together with a ARC WASHER(M10)
(26) and a NYLOCK NUT(M10x1.5)(23). Repeat to assemble the other SPACER TUBES(11) between
the UPRIGHT(2) and the DIP STAND(5).
NOTE: When assembling the SPACER TUBE(11), start from the one at the lower position.
STEP 4
Attach the PULL-UP BAR(3) to both the UPRIGHTS(2) with HEX BOLTS(M8x1.25x50mm)(20) and
ARC WASHERS(M8)(25).
SECURELY TIGHTEN ALL OF THE BOLTS FROM STEP 1 TO STEP 4.
To assemble the SPACER
TUBES(11), start from the one
at the lower position.