Titan Fitness X3SQUAT1 User manual

MPN: X3SQUAT1-X3SQUAT2-X3HALF
Owner’s Manual

2
P A R T S D I A G R A M & P A R T S / H A R D W A R E L I S T -

3
KEY #
BOX
DESCRIPTION
QTY
(1)
1
UPRIGHT POLE
x2
(2)
2
SIDE LEG
x2
(3)
2
BACK BOTTOM BRACE
x1
(4)
2
HD J-HOOK
x2
(5)
2
GUSSET PLATE
x4
(6)
2
PULL-UP BAR
x1
(7)
2
SQUARE TUBE CAP
x4
(8)
2
M16x120 HEX BOLT
x12
(9)
2
M16 FLAT WASHER
x16
(10)
2
M16 SPRING WASHER
x16
(11)
2
M16 HEX NUT
x16
(12)
2
M16x110 HEX BOLT
x4
(13)
3
3x3” UPRIGHT
x2
(14)
3
GUSSET PLATE
x2
(15)
3
LASER-CUT SIDE BRACE
x2
(16)
3
PIPE SAFETY BAR SLEEVE
x2
(17)
3
PIN SAFETY BAR
x2
(18)
3
M16x110 BOLT
x12
(19)
3
M16 FLAT WASHER
x12
(20)
3
M16 SPRING WASHER
x12
(21)
3
M16 HEX NUT
x12
BOX BREAKDOWN
•X3SQUAT1 = BOX 1
•X3SQUAT2 = BOX 2
•X3HALF = BOX 3

4
A S S E M B L Y I N S T R U C T I O N S -
IMPORTANT:
•Before assembly, it is recommended to create distinct areas for each box’s contents and
organize the parts and hardware.
•During assembling, make sure to loosely hand-tighten all nut-and-bolt combinations.
•Once assembly is finished, tighten all nut-and-bolt combinations to stabilize the product.
1. Lay out both SIDE LEGS (2) and the BACK BOTTOM BRACE (3) on a flat surface as seen above.
2. As indicated by the blue lines in the image above, place one GUSSET PLATE (14) on each outside
end of the SIDE LEGS (2) where the BACK BOTTOM BRACE (3) is located, and secure the GUSSET
PLATES (14), SIDE LEGS (2), and BACK BOTTOM BRACE (3) together with the following hardware:
M16x120 HEX BOLTS (8), M16 FLAT WASHERS (9), M16 SPRING WASHERS (10), and M16 HEX
NUTS (11).
3. Secure one GUSSET PLATE (5) to each center side of the SIDE LEGS (2) with the following
hardware: M16x120 HEX BOLTS (8), M16 FLAT WASHERS (9), M16 SPRING WASHERS (10), and
M16 HEX NUTS (11).
4. Insert a SQUARE TUBE CAP (7) into each end of the SIDE LEGS (2).

5
For the next two steps, it is recommended that one person holds the parts while another installs
the hardware.
5. Stand each UPRIGHT POLE (1) between a pair of center GUSSET PLATES (5), and secure them with
the following hardware: M16x120 HEX BOLTS (8), M16 FLAT WASHERS (9), M16 SPRING
WASHERS (10), and M16 HEX NUTS (11).
6. Secure the PULL-UP BAR (6) to the UPRIGHT POLES (1) with the following hardware: M16x110
HEX BOLTS (12), M16 FLAT WASHERS (9), M16 SPRING WASHERS (10), and M16 HEX NUTS (11).
7. Install the HD J-HOOKS (4).

6
For step 8, it is recommended that one person holds the parts while another installs the hardware.
8. Stand a 3x3”UPRIGHT (13) on top of each SIDE LEG (2) at the leg’s end where the GUSSET PLATE
(14) is located. Align the holes of each 3x3”UPRIGHT (13) with the top two holes of their adjacent
GUSSET PLATE (14), and secure them with the following hardware: M16x110 HEX BOLTS (18),
M16 FLAT WASHERS (19), M16 SPRING WASHERS (20), and M16 HEX NUTS (21).
9. Using the same hardware from the previous step, attach each LASER-CUT SIDE BRACE (15)
between an UPRIGHT POLE (1) and its adjacent 3x3”UPRIGHT (13).
10.Hold a PIPE SAFETY BAR SLEEVE (16) between each UPRIGHT POLE (1) and its adjacent 3x3”
UPRIGHT (13), and then slide a PIN SAFETY BAR (17) through the UPRIGHT POLE (1), PIPE SAFETY
BAR SLEEVE (16), and 3x3”UPRIGHT (13).

7
This concludes the
assembly of your
product.
Make sure to tighten
all nut-and-bolt
combinations before
use.
Enjoy!
NEED HELP?
CONTACT US FIRST.
1 [phone]
[e-mail] / www.titan.fitness
Business Hours: Monday–Friday • 8:00 a.m.–5:00 p.m. (CT)