Titan TTS-S13+ User manual

HD Telescopic Visual Inspection System
User Manual

7”
Monitor Digital Waterproof Inspection System
Thank you for purchasing this device. This handbook can lead you to use our product and the applied
program of its adding.
NOTES
1. We try our best to make the content correct and complete, but it can’t certify that there is no any
mistake and omit of the introduction.
2. Our company is only responsible for maintaining and repairing the problem of itself existing. We
aren’t responsible for personal data deleted and lost caused by wrong operation, product repair or
other case. We are also not responsible for any other indirect loss caused by this.
3. Any modify of software, hardware, introduction of this product will not be notified separately, and
our company owns the final explanation rights.

Content
Notes…….………………………………………………………………………………1
Basic Information……………………………………………………………………….2
Device Structure……………………………………………………….……………......3
Buttons & Interface……………………………………………………….……………..4
Stretch and Retract Telescopic Pole……………………………………………………. 5
Monitor Installation………………………………………………………………………6
Loading & Unloading of Sunshade Cover……………………………………………….7
How to Charge……………………………………………………………………………8
Basic Operation..………………………………………………………………………….9
Recording & Photo………………………………………………………………………10
Play Video & Pictures..…………………………………………………………………..12
System Settings ………………………………………………………………………….14
Trouble Shooting…………………………………………………….………………… .22
Specification………………………………………………………….………………….23
Package Content…………………………………………………………………………25

- 1 -
Notes
Dear customers, thank you for choosing our device. We really hope our product can bring
happiness to you. Please read the following instructions carefully before using:
 Forbid to use it in high temperature environment.
 Please inserting or pulling out the TF card after monitor power off. If under working
state, the huge current will bring unpredictable damage to the machine.
 Put it in the place where the children are not able to touch, in case it falling down or
against sharp objects, which will bring serious damage to the machine.
 Please don’t dismantle the device without authorization. If any query, please contact
with the distributor or our company.
 Please don’t change or poke the battery. If put the battery into fire, it will explode and
hurt people.
 Please don’t use it as driving or doing the work, which need your high attention.
 We suggest customer to copy the data in case any loss caused by unstable power supply.
Otherwise our company will not be responsible for any damage.
 When inserting TF card, please make sure the inserting direction is correct. Otherwise it
will damage the card slot, which users need to bear it by themselves.
 DO NOT use this product to violate others’ privacy. Monitoring others’ activities
without consent is illegal and this product is not designed and manufactured for such
purpose;
 DO NOT use this product for any illegal activities. We shall not be responsible for any
consequences of illegal acts committed by the user.

- 2 -
Basic Information
 Camera: Full HD 1080P camera
 Light source: 6 pcs LED/ IR lamps
 Camera resolution: 5.0 MP 3200*1800 pixel
 Telescopic Pole: 5 meters
 Metal monitor bracket: Adjustable
 Monitor: 7-inch HD screen with sun visor
 HD Video Output Interference：FPD-LinkⅢ
 Video Storage Pixels: HDMI：1920 * 1080
 Video Compression Format: H.264
 Photo Format：JPG 5.0 Mega 3200（H）×1800（V）
 Battery：Built-in 5000mAh high capacity Li-battery.
 Working Time: 8 hours
 Working Voltage: 5-24V
 Storage: Supports up to 64GB TF card.
 Language: Supports multi-language.
 Supports Power-saving Mode: Automatic shutdown, automatic off-screen.
 Automatic upgrade: Supports system automatic upgrade.
 Video Output: HDMI, AV-OUT
 Aluminum Alloy case : Fully preservation

- 3 -
Device Structure

- 4 -
Buttons & Interface
Tips for symbols

- 5 -
Stretch & Retract Telescopic Pole
Stretch the cable, anti-clockwise loosen the loose collars one by one to stretch the pole. Then
clockwise fasten the loose collars.
Retract the pole, anti-clockwise loosen the loose collars one by one. Then pull out the cable in
end of the pole to retract the pole. Clockwise fasten the loose collars.

- 6 -
Monitor Installation
Aim the nut opening on DVR bottom at the insert bolt on the pole, and fasten Bolt 1 with Chain.
Fix the direction & angle by adjusting Bolt 2 & 3.
Insert/pull out data line: Just catch the 5 pin connector to plug it into DVR female slot, then
fasten the nut; When pull it out, just loosen the nut and pull it out.

- 7 -
Loading & Unloading of Sunshade Cover
Loading & Unloading Methods of Sunshade Cover
The bottom of sunshade cover is provided with 4 buckle pins. Please aim them at the button holes
on monitor and push gently; it’s loaded in place. If need to unload it, just gently push it to
the opposite direction.
Open operation of the sunshade cover: just push up the button in the middle of cover; it pop open.

- 8 -
How to Charge
1. Notice before operation
Battery capacity symbols:
Tips: The possible reason for being unable to power on monitor is battery running out. Please
operate it after charging by AC adapter or PC.
2. How to charge
Charge 4~6 hours for fully charged. Unplug the charger until the battery status is full.
Notice:
A. This charger is for this machine use only. Do not leave the charger in humid place. Unplug
the charger and keep it well after charging. Do not repair, break down or remake the
charger.
B. For better performance, please charge the brand new machine for more than 6 but less than
10 hours for the first time. New battery will reach best performance after a few times full
charge and discharge.
C. If no need to use in a long time, it’s recommended to charge the monitor every 2~3 months
and then keep it after switch off.

- 9 -
Basic Operation
1. Power On/Off:
Press “ ” to power on, monitor is on working state; long time press “ ” again to power it off.
2. LED light turn on mode selection:
Turn on the monitor, LED is off. Press “ ” to turn on LED light, Press “ ” again to turn off
the LED light.
3. Working mode switch (switcher located in the left corner):
When it switches to “ ”, monitor is in state of receiving/record；
When it switches to “ ”, monitor is in the state of take photo；
When it switches to “ ”, monitor is in the state of playback.
4. External Storage card
Only after storage card being plugged in, this monitor can record, photo. Screen will show
symbol of TF card & its left capacity.
5. Working as a U-disk
Connect monitor to computer and power it on, it will work as a U-disk. Open the removable
disk in the computer, you’ll find the videos and photos in “ RECORD” and “ PHOTO” files
under “DICM” directory.

- 10 -
Record & Photo
Power monitor on, and select working mode to “ ”, it is in recording/photo mode.
1. Record: Under “ ” mode, press “ ”, monitor starts to record, and screen shows red “ ”.
Press “ ”again to pause and store, press “ ” one more time, it continue to record. Press “ ”
to end, it will save automatically and exit. If not press “ ”, the system will automatically save
video in segments until storage card is full.
2. Photo: Under “ ” mode, press “ ” once, screen flashes once, and get one picture.

- 11 -
Record & Photo
While if “Overwrite” is turn on, not press “ ” to end recording, system will automatically save
video in segments. And when the card is full, it will overwrite the earliest recording and save the
latest one, keep cycle recording.
3. Mute/Sound: Under “ ” mode, it is mute, press “ ”to enter state of sound. Press “ ” again
Screen displays “MUTE”. Speaker no sound;
Note: Mute setting will not affect earphone.(Only the monitor has audio function)

- 12 -
Play Video/Photo
When working mode selected to “ ”, it’s in the mode of play video & photo. Press “ ”/“ ”to
select “Photo” or “Video”. Press “ ” to exit and back to main menu. Press “ ”to get a delete dialogue.
1.Play Video: When select “Video”, press “ ” to enter into date folder. Press“ ”/“ ”to select
date, and press “ ” to enter into time phased video files. Press “ ”/“ ” to select, and press
“ ” to play video. Press “ ” long time to fast forward; press “ ” long time to rewind; press“ ”
to pause; press“ ” again to release pause; press “ ” to exit.

- 13 -
Play Video/Photo
2.Play Photos：Select “Photo”, and press “ ” to enter into photo files. Press“ ”/“ ” to select
pictures, then press “ ” to view. Press “ ” to view next one; press “ ” to view previous one.
Press “ ” to exit.
3. Delete Photo &Video：Under working mode, press “ ”/“ ”to select files. Press “ ” to
get a dialogue. Press“ ”/“ ” to select “All/Current”/“Cancel”.，Press “ ” to confirm.

- 14 -
System Settings
Press “ ” to enter system.
1. Language: Press “ ”/“ ”to select “Language”, and press “ ” to enter. Press “ ”/
“ ”to choose your language. And press “ ” to confirm and exit.

- 15 -
System Settings
2. Date Time: Press “ ”/“ ” to select “Date Time”, and press “ ” to enter. Press “ ”
again to move the cursor, and press“ ”/“ ” to adjust date & time. Press “ ” to exit.
3. Video Size: Press“ ”/“ ” to select “Video Size” and press “ ” to enter. Press “ ”/
“ ” to select “848X480”/“1280X720”/“1920X1080”. Press “ ” to confirm & exit.

- 16 -
System Settings
4. Photo Size: Press“ ”/“ ” to select “Photo Size” and press “ ” to enter. Press “ ”/
“ ” to select “2M”/“3M”/“5M”Press “ ” to confirm & exit.
5. Video Segment Sizes: Press“ ”/“ ” to select “Video Segment Sizes” and press “ ” to
enter. Press “ ”/“ ” to select “10mins”/“30mins” Press “ ” to confirm & exit.

- 17 -
System Settings
6. Overwrite: Press “ ”/“ ” to select “ Overwrite”, and press “ ” to enter. Press“ ”/
“ ”to select “Off”/ “On”, and press “ ” to confirm & exit. If “Overwrite” is on, monitor
will cycle record, and save the latest video.
7. Light Frequence: Press“ ”/“ ” to select “Light Frequence” and press “ ” to enter. Press
“ ”/“ ”to select “50PS”/“60PS”, and press “ ” to confirm & exit.