TOORX CSX3000 User manual

Ed : 10/18 Rev : 00 Cod : GRLDTOORXCSX3000
INSTRUCTION

Components - Fixings
3

Components - Parts (1)
4

Components - Parts (2)
5

Components - Parts (3)
6

Tools: Adjustable spanner x 2
Attention:
It is strongly recommended to assemble the equipment by two or more people, otherwise it may
cause serious injury.
The icon indicates the spanner can be
directly used to tighten and secure
during assembly.
The icon indicates turn the bolt by hand
during assembly, but do not tighten
them so as not to affect next assembly
step.
Assembly Instructions
7

Step 1
1. Attach 2 x Base Frame (2) and 2 x Flat Bracket (21) to 2 x Rear Vertical Support (1) respectively using 2
x M10×60mm Carriage Bolts (37), 2 x φ10mm Washers (48) and 2 x M10 Aircraft Nuts (49).
2. Attach 1 x Cross Beam (3) and 2 x Flat Bracket (21) to 2 x Rear Vertical Support (1) respectively using 4
x M10×60mm Carriage Bolts (37), 4 x φ10mm Washers (48) and 4 x M10 Aircraft Nuts (49).
3. Attach 1 x Upper Connecting Frame (7) and 2 x Flat Bracket (21) to 2 x Rear Vertical Support (1)
respectively using 4 x M10×60mm Carriage Bolts (37), 4 x φ10mm Washers (48) and 4 x M10 Aircraft
Nuts (49).
Notes: The part (60) and (65) are pre-assembled.
8

Step 2
1. Attach 2 x Middle Vertical Support (4) to 2 x Base Frame (2) respectively using 2 x M10×100mm Allen
Bolts (39), 2 x φ10mm Washers (48) and 2 x M10 Aircraft Nuts (49).
9

Step 3
1. Put 2 x Guide Tube (5) through the L&R Sliding Frames (12, 13), and respectively screw 1 x
M18×1.5×φ12 T-shaped Pin (35) in the bolts of the L&R Sliding Frame (12, 13), then secure the
M18×1.5×φ12 T-shaped Pin (35) to facilitate the L&R Sliding Frame (12) are adjustable on the Guide
Tube (5).
2. Put the U-shaped brackets of 2 x Base Frame (2) through 2 x Guide Tube (5) respectively, and then fix
2 x Guide Tube (5) to 2 x Base Frame (2) respectively using 2 x M10×16 Allen Bolts (44) and 2 x
φ10mm Washers (48).
3. Fix 2 x Double Floating Pulley Bracket (14) to the L&R Sliding Frame (12, 13) using 1 x M12×90mm
Allen Bolts (38), 2 x φ12mm Washers (50) and 1 x M12 Aircraft Nut (51).
Notes: Parts (43, 55, 57, 58, 61, 64) are pre-assembled.
10

Step 4
1. Attach 2 x Upper Frames (6) and 2 x Flat Brackets (21) to 2 x Middle Vertical Support (4) and Guide
Tube (5) respectively using 4 x M10×60mm Carriage Bolts (37), 4 x φ10mm Washers (48) and 4 x M10
Aircraft Nuts (49).
2. Connect 1 x Cross Beam (3) to 2 x Rear Vertical Support (1) and 2 x Upper Frame (6) using 4 x
M10×60mm Carriage Bolts (37), 4 x φ10mm Washers (48) and 4 x M10 Aircraft Nuts (49).
11

Step 5
1. Fix 2 x Guide Rods (8) to the right Base Frame (2) using 2 x M10×25mm Allen Bolts (43).
2. Put the Guide Rod (8) through 1 x Rubber Bumper (28), 1 x Shock Spring (27) and 1 x Rubber
Bumper (28) sequentially.
3. Put the Guide Rod (8) through 15×5kg Selector Stems (29).
4. Respectively put 2 x Weight Stem Guiding Sleeve (31) into the 4kg Selector Stem (30), insert the
Selector Rod (22) into the 4kg Selector Stem (30), screw 2 x M10×25mm Allen Bolts (36) in the 4kg
Selector Stem (30) and fix the Selector Rod (22).
5. Put the Guide Rod (8) through 1 x 4kg Selector Stem (30).
6. Stick the weight sticker (32) as shown in the diagram, from top to bottom sticking 5kg, 10kg, 15kg,
20kg, 25kg, 30kg, 35kg, 40kg, 45kg, 50kg，55kg，60kg，65kg，70kg，75kg，80kg.
12

Step 6
Repeat Step 5 to assemble the left weight stack.
13

Step 7
1. Put left and right Guide Rod (8) through 2 x Guide Rod Holder (9).
2. Fix the 2 x Guide Rod Holder (9) to the middle between the L&R Middle Vertical Support (4) and the
Rear Vertical Support (1) using 4 x M10×60mm Carriage Bolts (37), 4 x φ10mm Washers (48), 4 x
M10 Aircraft Nuts (49) and 2 x Bracket (25).
14

Step 8
1. Fix the left and right Guide Rod Holder (9) to the Guide Rod (8) respectively using 2 x M10×25mm
Allen Bolts (43) and 1 x φ10mm Washer (48).
2. Fix the pulley bracket（74）to Selector Rod (22)
Notes: Parts (76) are pre-assembled.
15

Step 9
Attach the Hook Frame (11) to the Upper Connecting Frame (7) using 3 x M8×60mm Allen Bolts (45), 6 x
Ø8mm Washers (46) and 3 x M8 Aircraft Nuts (47).
16

Step 10
1. Attach the U-shape hook (75) to the Chin up bar Frame (10) using 2 x φ12 Curved Washers (54), 2 x
M12 Aircraft Nut (51).
2. Attach the Chin up bar Frame (10) to the middle of the 2 x Upper Frame (6) using 8 x φ10mm
Washers (48), 4 x M10 Aircraft Nut (49), 4 x M10×100mm Allen Bolts (39) and 2 x Arc Bracket (26).
Notes: Parts (43, 55, 56, 59, 63) are pre-assembled.
17

Step 11
1. Find out the end with threaded head of the Upper Cable (52) as shown in the diagram, thread the end
in sequence through the long notch on the right side of the Guide Tube (5), Middle Vertical Support (4)
and Guide Rod Holder (9), and finally screw Hinto the Guide Rod Holder (9).
2. Connect the Pulley φ114 A, B (34) and Upper Frame (52) to the Right Sliding Frame (12) using 1 x
M10×45 Allen Bolt (42), 2 x ø10mm Washers (48) and 1 x M10 Aircraft Nut (49), and ensure the cable
in pulley groove.
3. Connect the Pulley φ114 C(34) and Upper Frame (52) to the Guide Tube (5) using 1 x M10×65 Allen
Bolt (40), 2 x ø10mm Washers (48) and 1 x M10 Aircraft Nut (49), and ensure the cable in pulley
groove.
4. Connect the Pulley φ114 D(34) and Upper Frame (52) to the 2 x Double Pulley Bracket (15) and 1 x
L- Shaped Cable Protector (20) using 1 x M10×50 Allen Bolt (41), 2 x ø10mm Washers (48) and 1 x
M10 Aircraft Nut (49), and ensure the cable in pulley groove.
5. Fix the Pulley φ114 E(34) and Upper Frame (52) to the Guide Tube (5) using 1 x M10×100 Allen Bolt
(39), 2 x ø10mm Washers (48) and 1 x M10 Aircraft Nut (49), and ensure the cable in pulley groove.
6. Connect the Pulley φ90 F(77) and the Guide Tube (52) to the Guide Rod Holder (9) using 1 x
M10×45mm Allen Bolt (42),2 x ø10mm Washers (48) and 1 x M10 Aircraft Nut (49), and ensure the
cable in pulley groove.
7. Connect the Pulley φ90 G(77) and the Guide Tube (52) to the pulley bracket (74) using 1 x M10×45mm
Allen Bolt (42),2 x ø10mm Washers (48) and 1 x M10 Aircraft Nut (49), and ensure the cable in pulley
groove.
18

Step 12
Repeat the step 11 to assemble the left Upper Cable (52).
19

Step 13
1. Put the End Aof the Adjustment Cable (53) through the sleeve on the right side of the Right Sliding
Frame (12) as shown in the diagram, then screw the End Din the nut on the Base Frame (2).
2. Connect the Pulley φ114 B(34) and Adjustment Cable (53) to the Base Frame (2) using 1 x
M10×45mm Allen Bolt (42), 2 x ø10mm Washers (48) and 1 x M10 Aircraft Nut (49), and ensure the
cable in the pulley groove.
3. Connect the Pulley φ114 C(34) and Adjustment Cable (53) to 1 x L- Shaped Cable Protector (20) and
2 x Double Pulley Bracket (15) using 1 x M10×50mm Allen Bolt (41), 2 x ø10mm Washers (48) and 1 x
M10 Aircraft Nut (49).
4. Cable tension can be adjusted by the End Dof the Adjustment Cable (53).
20

Step 14
Repeat step 13 to assemble the left Adjustment Cable (53).
21