TOP VEHICLE TECH KWPOR3 User manual

www.topvehicletech.com
The informaon provided in this document is subject to change without noce due to changes and/or
improvements to the product/s.
This dash image is a visual representaon for display purposes only.
V1.0421
KWPOR3
INSTALLATION MANUAL
PORSCHE
PANAMERA


2
www.topvehicletech.com
ABOUT THIS PRODUCT
The KWPOR3 installaon kit allows for the retenon of the vehicle’s steering wheel controls and maintains the
original aesthec of the interior when installing a new car stereo. The KWPOR3 gives you everything you need
for a complete install in one box. The components of this kit are compable for the Porsche Panamera (2009-
2016) with non-amplied PCM 3.1 stereos. The wiring harness and Infodapter interface will retain the steering
wheel controls and factory phone buons, vehicle sengs and Aux and USB retenon. It also aids in generang
parking sensor graphics for the new stereo and provides an input for both an OEM and aermarket reverse
camera (if applicable). Supplied with a Quadlock connector.


CUSTOMER SUPPORT
Installaons should be carried out by, or under the guidance of an experienced installer. If you do encounter any
problems during the installaon of this product, then please contact our dedicated customer service team at:
Phone: [phone] E-Mail: 
CONTENTS
• 1x Fascia plate (with accessories)
• 1x Instrucon manual
• 1x Steering wheel control harness and Infodapter interface (with USB retenon lead)
• 1x Antenna adapter
• 1x DAB antenna adapter
• 1x Stereo patch lead

3
www.topvehicletech.com
FITTING GUIDE
1. Open the passenger side door and proceed to pull away the door trim from the pillar.
STEREO REMOVAL
DAB ANTENNA INSTALLATION
2. Using a set of panel removal tools, begin to pry away the pillar casing.
4. The DAB antenna not only has a self adhesive backing, but also features a black earth sheet. When
placing the DAB antenna, the earth sheet MUST be placed onto the metal part of the pillar. The antenna
itself must be located roughly 15cm from the top of the windscreen.


5. Once happy with the placement, take the 3m of wiring extension and feed it down through to the
stereo’s opening. With the wiring adjusted to the appropriate length, feel free to re-install the glovebox.
3. The glovebox will need to be opened/removed to route the antennas wiring.
1. Remove both the le and right air vents by using a at blade. You need to release 6x clips from the
inside of the vents: 2x le, 2x right, 1x top, 1x boom. These clips are holding the vents rmly into place.
Once out, disconnect the wiring.
3. Remove the 4x screws that secure the main stereo and remove whilst disconnecng the wiring.

3. When happy with the alignment, and the “Stereo Installaon” process is complete, screw the stereo
into the dashboard using the pre-exisng screws. Then re-install the vents either side, re-connecng the
wiring in the process.
1. Aach the brackets to the new stereo using the screws within the kit. With the brackets aached, oer
the whole unit to the back of the fascia. With the correct depth, aach the brackets to the fascia.
2. Before removing the head unit, it is best to put gear shier in either ‘Drive’ or ‘4th’ gear to allow for
room when removing radio.
2. Secure the stereo to the fascia panel using the four star clips by pushing each clip onto a spoke located
on the rear of the fascia panel.

4
www.topvehicletech.com
FITTING GUIDE
STEREO INSTALLATION
9. Aach the addional wiring on the harness to the back of the stereo:
- Speed Pulse  - Reverse Gear  - Park Brake  - Amp Remote  - Mute
10. When all the above wires (and any addional accessories) have been connected, nally make the
connecons between the stereo and the vehicles pre-exisng power/stalk connectors.
2. Connect the bullet connector from the stereo patch lead to the ‘steering wheel remote input’ on the
back of the new stereo.
7. Connect the DAB antenna’s SMB connector to the back of the new stereo.
8. Aach the antenna adapter to the vehicles pre-exisng connecon and the back of new stereo.
1. Take the steering wheel control interface in hand and connect both the 12-way stereo patch lead and
the 14-way steering wheel harness connectors to the corresponding sides.
4. Connect the yellow RCA connector to from the camera extension to the reverse camera input of the
stereo.
To retain factory OEM reverse camera: aach the yellow female RCA from on the camera extension
harness to the male yellow RCA on the main wiring harness.
To add an aermarket reverse camera: aach the yellow female RCA from on the camera extension
harness to the male yellow RCA of the aermarket reverse camera.
5. Connect the USB retenon lead between the vehicles OEM connecon and the USB connecon from
the stereo.
6. Connect the Red/White RCA connectors labelled ‘AUX’ to the back of the new stereo.
3. Connect the 4-way connector on the camera extension harness to the interface.

On this parcular interface are a set of dipswitches. These dipswitches have the following properes:
1: OFF - Kenwood. ON - Pioneer.
2: OFF - NTSC reversing camera (default). ON - PAL reversing camera.
3: Change from OFF to ON to ‘reset’ screen seng to factory default.
Note: during this procedure, the screen background will change to red and no sengs adjustments can be made.
4: Not Used.

5
www.topvehicletech.com
Please note: conguraon layout may dier dependent on vehicle model.
STEERING WHEEL CONTROL FUNCTIONALITY
12
3 4
5 6
7
1. Volume +/- (Scroll) 2. Instrument Cluster Navigaon
Mute (Short Press) 4. Instrument Cluster Navigaon
 5. Pick Up
3. Programmable Funcon 6. Hang Up
(on both Short & Long Press)*
7. Source (Short Press) Voice Assist (Long Press)
STEERING WHEEL CONTROLS
1. Menu + / Menu - 2 - 7. Funcons as above.
Select Menu Item (Short Press)


1. Camera / Parking Graphics Toggle (Long Press)
 
The diamond buon on the steering wheel can be programmed to perform specic radio funcons whilst
in the Infodapter menus on both a long and short press. Funcon opons include: 
 and . To assign a funcon, enter the Infodapter menu and go to the ‘Preferences’ sub-menu.
Select the desired buon funcon against the ‘Diamond Short Press’ and ‘Diamond Long Press’ opons.
any radio funcon in the
OEM instrument cluster menu
NonePreferences
*PROGRAMMABLE BUTTON

6
www.topvehicletech.com
INFODAPTER FUNCTIONALITY
INFODAPTER SETTINGS
Within ‘Infodapter Sengs’ you are able to alter a the look and feel of the Infodapters menu/display:
Screen Size/Posion Picture Sengs
• Horizontal Size • Brightness
• Horizontal Posion • Contrast
• Vercal Size • Saturaon
• Vercal Posion
Preferences
• Camera Connected - Choose the style of camera connected to the vehicle (if applicable).
• *Camera Acve (OEM/Reverse) - Choose whether the image appears on the display when triggered by
the Porsche system, or only when reverse gear is acve.
• *RVC Grid Lines (Yes/No) - Rear view camera guidelines.
• **Reverse Priority (Park Assist/Camera) - Choose whether the display shows the parking graphics or
reverse camera image on screen. 
• **Camera Delay (0 to 20) - Increase camera delay to reduce ‘rolling’ eect on screen when switching.
• Diamond Short Press - Select ‘short press’ funcon for steering wheel control
• Diamond Long Press - Select ‘long press’ funcon for steering wheel control
• Park Brake Source - Set ‘Park Brake’ output to acvate when park brake is on (Brake), when speed is less
than 3km/h (Speed) or to remain on at all mes (Always On).
• Restore Factory Sengs - select ‘Yes’ to return all Infodapter sengs to factory defaults.

Within the ‘Language’ menu, you are able to select between a wide array of dialects. This is default to
English upon installaon.
Within ‘Version’, you are able to view the current rmware that is being ulised by the Infodapter.
As well as steering wheel control funconality, this interface allows the retenon of key vehicle features
and funcons via a bespoke ‘Infodapter’. Accessing the Infodapter, you are able to navigate through the
following opons and sengs:
*Only available when using OEM camera
**Only available when using OEM or Aermarket camera
OEM PARKING SENSOR GRAPHICS
The Infodapter interface will automacally generate a replicaon of the OEM front/rear parking sensor
graphics based on the vehicle’s data. These graphics have been designed to replicate the Porsche’s original
data to retain the OEM feel of the system.
To toggle between the reversing camera and the parking graphics while one is acve on screen, hold
down the Volume buon (1) whilst the camera or graphics are acve. This seng can be changed by the
‘Reverse Priority’ seng in the ‘Preferences’ sub-menu.


7
www.topvehicletech.com
ISO Connector
Connect to aftermarket stereo
Quadlock Connector
Connect to quadlock connector from vehicle
Main Wiring Loom
Connector [14 Pin]
Connect to Interface Box
White/Red RCA
Connectors (AUX)
Connect to
aftermarket stereo
Flying Wires
Pink - Speed Pulse
Green - Park Brake
Purple/White - Reverse Gear
Blue/White - Amp Remote
Grey - Mute
Male Yellow RCA Connector
Connect to Female Yellow RCA
for factory camera retention.
AUX
SPKR
White/Red RCA
Connectors
(Speaker)
Not Used
Molex Connector [8 Pin]
Not Used
Male Yellow RCA Connector
Connect to stereos camera input
Female Yellow RCA Connector
Connect to aftermarket camera
or Male Yellow from harness.
Stereo Patch Lead Connector [12 Pin]
Connect to Interface Box
Note: Must be connected first before power
connection is made to the interface
Stereo Patch Lead Bullet Connector
Connect to ‘Steering Wheel Remote Input’
on back of the stereo.
USB Retention Lead
Connect to vehicle Connect to aftermarket stereo
WIRING DIAGRAM

8
www.topvehicletech.com
If at any point you experience any problems and need any assistance before, during or aer the
installaon process, please contact us via :
Phone: [phone]
E-Mail: 
Mon - Fri 9am - 5.30pm GMT
TECHNICAL ASSISTANCE
If you would like to download a digital copy of this manual, or any other product, then please
visit the www.topvehicletech.com website.
This manual is considered correct at the me of prinng but is subject to change. For the latest
manuals & updates, refer to our website.
Copyright 2021 by TopVehicleTech.
All rights reserved. No part of this publicaon may be reproduced, distributed or transmied
in any form or by any means, including photocopying, recording, copying or other electronic or
mechanical methods, without the prior wrien permission of the author.