Toro 04265 User manual

FormNo.3369-988RevC
LEDLightKit
Walk-BehindGreensmaster®Flex1800/2100andeFlex1800/2100
MowersEquippedwithSubaruEX13orLithiumIonBattery
ModelNo.04265
InstallationInstructions
Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
DescriptionQty.Use
Wireharness–LED1
Wireharness–Powersupply(Gasmodels
only)1
LEDlightwithmountinghardware(1bolt,1
washer,1nut)2
Flangenut6
Washer2
Rightbar1
Leftbar1
Switch1
Bolt(5/16x1inch)2
Bolt(5/16x1–1/4inch)4
Cabletie5
InstallationInstructions1
PartsCatalog1
InstallingtheLEDlightkit.
Note:Rightandleftaredeterminedfromthestandard
operatingposition.
©2013—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.OriginalInstructions(EN)
PrintedintheUSA.
AllRightsReserved

1.Mounttherightbartotherightsideofthemower
usingtwobolts(5/16x1–1/4inch)andtwoange
nuts(Figure1).
2.Repeattheprocedurefortheleftside,usingtheleft
bar.
7
g02341 1
1
2
3
4
5
6
7
Figure1
1.Bolt(5/16x1inch)4.Rightbar7.Flangenut
2.LEDlight5.Leftbar
3.Bolt(5/16x1–1/4inch)6.Washer
2

3.Securethetwobarstogetherusing2bolts(5/16x
1inch),2washers,and2angenuts(Figure1and
Figure2).Alignthebarholesfor18or21inchwide
mowers.
12
g016952
12
3
4
Figure2
1.Rightbar3.21inchalignment
2.Leftbar4.18inchalignment
4.MounttheLEDlightstothebarsusingthehardware
suppliedwiththelights(Figure1).
5.Removethe(4)screwssecuringtheconsolecoverto
thehandleandremovethecover(Figure3).Retain
thecoverandscrews.
6.Removetheholeplugfromthecontrolpanel
(Figure3).
7.InserttheOn/Offswitchintotheholeinthe
controlpanel,positioningitsothethinnerendis
towardthebottomofthecontrolpanel(Figure3).
4
3
2
1
G023457
Figure3
1.On/Offswitch3.Screws(4)
2.Holeplug4.Consolecover
8.RoutetheLEDwireharnessdowntheLHsideofthe
handleandacrossthelightbarasshowninFigure4.
G023506
2
1
Figure4
1.Lightbar2.Wireharness
9.Plugthewireharnessconnectorsintothelights
(Figure4).
10.Connectthewireharnessasfollows:
•Ongasmodels
A.Plugthepowersupplywireharnessconnector
intotheOn/Offswitch.
B.Plugthepowersupplywireharnessconnector
intotheconnectoronLEDlightwireharness.
3

C.Routethepowersupplywireharnessdown
theLHsideofthehandletowardstherear
oftheengine.
D.Connecttheharnesstothetwobullet
connectorscomingfromtheengineshroud.
•Onbatterymodels
A.Locatetheopenwireharnessconnectoron
theeFlexmainwireharness.
B.ConnecttheLEDlightwireharnesstothe
lightconnectorplugontheeFlexmainwire
harness.
C.InstalltheswitchconnectorplugontheeFlex
mainwireharnesstotheOn/Offswitch.
Theremainingwireharnesswillnotbeused
forthisapplication.
11.Looselyattachthewireharnesstothelightbarand
handlewith(5)cableties(Figure5).
G023458
1
1
Figure5
1.Cabletie(5)
Note:Beforetighteningthecableties,makesure
theLEDlightsaredirectedslightlydownward
fromtheexpectednalposition.Thiscanprevent
damagingtheharnessconnectorswhen/ifthelights
arerotateddownward.
Important:Ifthehandleisnotfullyextended
out,makesurethereissufcientslackinthe
wireharness(approximately3inches)between
thelowestcabletieonthehandleandthe
connectingpointsontheengine(gasmodels
only)andthelightbar.
12.Installtheconsolecovertothehandlewiththe(4)
screwspreviouslyremoved.
13.Tightenthecableties.
4