Gamma+ Luxe Cannon 600 Z IP User manual

①
Leko Cannon
LED 300
(CW/WW)
User Manual
IP65
Luxé Cannon
600 Z IP (VW)

②
SAFETY INSTRUCTIONS
This device has left the factory in perfect condition. In order to maintain this condition and
to ensure a safe operation, it is absolutely necessary for the user to follow the safety
instructions and warning notes written in this user manual.
If the device has been exposed to temperature changes due to environmental changes, do
not switch it on immediately. The arising condensation could damage the device.
Leave the device switched off until it has reached room temperature.
This device falls under protection-class I. Therefore it is essential that the device be
earthed.
The electric connection must carry out by qualified person. The device shall only be used
with rate voltage and frequency.
Make sure that the available voltage is not higher than stated at the end of this manual.
Make sure the power cord is never crimped or damaged by sharp edges. If this would be
the case, replacement of the cable must be done by an authorized dealer.
Always disconnect from the mains, when the device is not in use or before cleaning it. Only
handle the power cord by the plug. Never pull out the plug by tugging the power cord.
During initial start-up some smoke or smell may arise. This is a normal process and does
not necessarily mean that the device is defective, it should decrease gradually.
Please don't project the beam onto combustible substances.
Fixtures cannot be installed on combustible substances, keep more than 50cm distance
with wall for smooth air flow, so there should be no shelter for fans and ventilation for heat
radiation.
Becareful with your operations.With a dangerous voltage you cansuffer
a dangerous electric shock when touching wires!
Damages caused by the disregard of this user manual are not subject to
warranty. The dealer will not accept liability for any resulting defects or
problems.

③
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively
replaced by the manufacturer or his service agent or a similar qualified person in order to
avoid a hazard.
Please pay attention below warnings before using
this fixture!

④
Unpacking
Thank you for choosing Leko Cannon 300 -CW+WW. For your own safety, please read this
manual before installing the device. This manual covers the important information on installation
and applications. Please install and operate the fixture with following instructions. Meanwhile,
please keep this manual well for future needs.
The Leko Cannon 300 -CW+WW is made of a new type of high temperature strength of die cast
aluminum casing with nice outlook. The fixture is designed and manufactured strictly following
CE&RoHS standards, complying with international standard DMX512 protocol. It's available
independently controlled and linkable with each other for operation. And it is applicable for
large-scale live performances, theater, studio, nightclubs and discos.
The Leko Cannon 300 adopts 1PCS 600W COB LED (available for cool white+warm white 2in1)
which features high brightness and stability. Please carefully unpack it when you receive the
fixture and check whether it is damaged during the transportation. And please check whether the
following items are included inside the box:
①
②

⑤
③
FEATURES & SPECIFICATIONS
Feature
：
* 1 * 300W COB LED (Cool White+Warm White 2in1)
* Color temperature: 3000K-6000K
* 50,000 hours life time and low power consumption
* Optimized high definition optical system for improved photometric performance and field
uniformity
* Projector-quality, high contrast aspheric lens
* Glass reflector that removes greater than 90% infrared radiation (heat) and reflects greater than
95% of visible light
* Input Voltage:AC100-240V 50/60Hz
* Beam Angle: 15°to 30°
* Zoom Function: Auto zoom by DMX
* Shutter controlled by DMX (auto cutting to any shapes)
* Die casting aluminum housing design
* 4 kinds of dimming curve
* Dimming Frequency: 500HZ - 25000HZ optional
* High-quality optical system, glass aspherical
* 17 DMX channels
* Control Protocol: RDM / DMX , Auto run and Master/Slave control system
* LCD with touch screen
* Fan-less no noise Cooling system
* Working Temperature: -10℃~40℃
* IP65 protection rating
① Leko Cannon
300-CW+WW
1PC
②POWER cable
1PC
③ User Manual
1PC
3
③

⑥
Specifications
：
*Input Voltage:AC100-240V 50/60Hz
*Max. Power: 300W
*Net Weight: 16.5kg
*Gross Weight: 20kg
*Production size: 76.76*29.73*27.37CM
*Packing size: 86*37*35cm(1pc/carton)
DMX-512 CONTROL CONNECTIONS
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the other
side to the male 3-pin XLR input of the moving head. You can chain multiple
Moving head together through serial linking. The cable needed should be two core, screened
cable with XLR input and output connectors. Please refer to the diagram below.
DMX-512 connection with DMX terminator
4

⑦
DMX Input
3-Pin XLR
DMX512 Out DMX512 In
3-Pin XLR 3-Pin XLR
1:Ground
2:Data(-)
3:Data(+)
COMMON
DMX+
DMX-
120Ω
Pin2
Pin3
DMX INPUT
DMX OUTPUT
POWER IN

⑧
For installations where the DMX cable has to run a long distance or is in an electrically noisy
environment, such as in a discotheque, it is recommended to use a DMX terminator. This helps
in preventing corruption of the digital control signal by electrical noise. The DMX terminator is
simply an XLR plug with a 120 Ω resistor connected between pins 2 and 3,which is then
plugged into the output XLR socket of the last fixture in the chain. Please see illustrations
below.
Product Feature
Ø 2 kinds of running model
n External control mode (Slave model)
u DMX 512 controller control(2 kinds channel modes)
u Master/salve model control (auto match the signal from controller and the Master
light, no need to set by menu)
n static mode (Master model)
u It can fix any color without the controller ,also work this color with strobe
Ø Non-linear dimmer and linear dimmer
n The speed of dimmer can be set under the controller control
Ø Screen Protect
n It will enter blank screen without any operate on the keyboard in 30 seconds . Press any
keys then it can quit screen protection.
Ø Temperature Protection
n It can be set to temperature protection mode
Ø Can be Reverse display
5

⑨
Multi-light working in the same time
When using controller to control multi lights to work in strobe, the controller just send the
channel data . The strobe effect will be depend on each light itself . And please take attention for
the follow situation:
1. There will be many situations make the lights are not synchronization in the beginning. (For
example: the different time of opening the light , or different time of them connect to the
controller) .In this case, you can change value of the controller( for example push 20 to 0, and
back to 20), then it can be synchronization.
2. Due to crystal frequency of different lights are not the same exactly, so it may not be
synchronization after long time.
3. If need to keep synchronization for long time, there are two ways to do so:
A. Using the controller to edit program make the strobe, auto run effect,then they must be
synchronization.
B. Using the Maser/Slave model
Main Menu
6.1 Main Menu
1 2
6
Reverse Display
Running Status
Vice Menu Button

⑩
6.2 Operation Status
Mode
Display
Description
DMX Mode
Dxxx
“D”stand for DMX mode
Temperature
Mode
M-WP
“M”stand for stand Master, “WP”stand for“White
Point”
DMX Menu
Enter DMX mode:
1. If you are in DMX mode,the main menu will turn into DMX menu automatically after 5 seconds
2. Menu of DMX address (DMX mode) will turn into DMX menu automatically after 5 seconds
DMX Menu Operation:

11
1. DMX mode: When the DMX 512 signal is connected correctly and the data of channel 1 which is
bigger than 0, use the received DMX data value for dimmer and temperature control
Vice Menu
7.1 Master Mode: (Color temperature)
Menu
State
Operation
White Point
Press “ok” to choose this mode
Choose Color temperature（3000~6000K）
Motor Control
Same as above
Control the motor
7.2 Motor Control
Remarks: The meaning of below menu data are completely the same as DMX channels data.
As "left"and "right" are relative concept, so the left point and right point of shutter separately use
alphabet A, B for instead.
Menu
Data
Function
Remark
Reset
Push "Confirm" to reset
M1
0~255
M1、M2 Position control
Push "Confirm" to edit
M2
0~63
M1、M2 Angle control (Over
Point A)
Point A gradually raise to
the maximum angle
64~127
M1、M2Angle control (Back
Point A gradually drops
to the level of point B
7

12
to Point A)
128~191
M1、M2 Angle control (Over
Point B)
Point B gradually raise to
the maximum angle
192~255
M1、M2 Angle control (Back
to Point B)
Point B gradually drops
to the level of point A
M3
0~255
M3、M4 Position control
Refer to M1
M4
0~255
M3、M4 Angle control
Refer to M2
M5
0~255
M5、M6 Position control
Refer to M1
M6
0~255
M5、M6 Angle control
Refer to M2
M7
0~255
M7、M8 Position control
Refer to M1
M8
0~255
M7、M8 Angle control
Refer to M2
Auto Zoom
0~255
Auto Zoom
Focus adjustment
0~255
Focus adjustment
Gobo
0~127
Gobo angle
128~191
Gobo rotation
192~255
Gobo rotation (reverse)
Iris
0~255
Iris
Macro
0~63
No function
64~255
Built-in shape cutting
7.3 Status
Software
Name of software
Version
Version
Temperature
Show the current temperature of the fixture
DMX Status
Show“OK”（Slave，with DMX signal）， “NONE”（Slave，without DMX signal）、 “Master”
（Master）
……
（other）
7.4 Setting
Menu
State
Option
Mark
Touch Screen Calibration
Touch Screen
Calibration
Reset Calibratioin
Dimmer Frequency
Choose the
dimmer
500HZ
……
Increase or decrease

13
frequency
with data of 100HZ
25000HZ
Dimmer Curve
Choose the
dimmer curve
Standard
Incandescent
Linear
Quick
Over Temperature
Set the protect
temperature
45~95
Increase or decrease
with data of 5
Backlight
Adjust the
Backlight
brightness
10%~100%
Increase or decrease
with data of 5%
Backlight Timeout
Set the screen
protect time
screen protect or screen
protect after 5~60 seconds
Increase or decrease
with data of 5
Load Factory Settings
Reset
DMX CHANNELS
17CH
8

14
Channel
Data
Function
Remark
1
0~255
Dimmer
2
0~11
3000K
Color
temperature 1
8 = 1*8
Totally 31 kinds
of color
temperature.
Quick color: If
you need the
color of N, then
take the data
value of N*8. For
example you
need the color 1:
1*8, to push the
channel data in 8.
12~19
3100K
Each 8 data is for
a color
temperature
16 = 2*8
20~235
3200K~5800K
(V = N*8)
236~243
5900K
240 =
30*8
244~255
6000K
Color
temperature 31
248 =
31*8
3
0~10
No function
11~255
Strobe Speed(255
fastest)
4
0~255
M1, M2 position control
5
0~63
M1, M2 Control straight
up and down by channel
3
64~127
M1, M2 Angle
adjustment(big data, big
angle)
128~191
M1, M2 back to original
position
192~255
M1,M2 Reverse angle
adjustment,(big data, big
angle)
6
0~255
M3,M4 position control
7
M3,M4 position
control(refer to channel
4)
8
0~255
M5,M6, position control
9
M5,M6, position control
(refer to channel 4)
10
0~255
M7,M8 position control
11
M7,M8 position control
(refer to channel 4)
12
0~255
Auto Zoom
13
0~255
Focus adjustment
14
0~255
Gobo control-optional
Reserve channel for gobo control
15
0~255
Iris control-optional
Reserve channel for iris control
16
0~63
No function
64~255
Built-in shape cutting
17
0~249
No function
250~255
Motor reset

15
OPERATION & SPECIFICATIONS
·The Leko Cannon 300 is for on-site decoration purpose.
·Don't turn on the fixture if it's been through severe temperature difference like after transportation
because it might damage the light due to the environment changes. So make sure to operate the
fixture until it is in normal temperature.
·This light should be keep away from strong shaking during any transportation or movement.
·Don't pull up the light by only the head, or it might cause damages to the mechanical parts.
·Don't expose the fixture in overheat, moisture or environment with too much dust when installing
it. And don't lay any power cables on the floor. Or it might cause electronic shock to the people.
·Make sure the installation place is in good safety condition before installing the fixture.
·Make sure to put the safety chain and check whether the screws are screwed properly when
installing the fixture.
·Make sure the lens are in good condition. It's recommended to replace the units if there are any
damages or severe scratch.
·Make sure the fixture is operated by qualified personnel who knows the fixture before using.
·Keep the original packages if any second shipment is needed.
·Don't try to change the fixtures without any instruction by the manufacturer or the appointed
repairing agencies.
·It is not in warranty range if there are any malfunctions from not following the user manual to
operate or any illegal operation, like shock short circuit, electronic shock, lamp broke, etc.
INSTALLATIONS
For added protection mount the fixtures in areas outside walking paths, seating areas, or in areas
were the fixture might be reached by unauthorized personnel.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 times the device's weight.
Fixture installation must always be secured with a secondary safety attachment, such as an
appropriate safety cable.
Never stand directly below the device when mounting, removing, or servicing the fixture.
From a ceiling, or set on a flat level surface (see illustration below). Be sure this fixture is kept at
least 0.5m (1.5 ft) away from any flammable materials (decoration etc.).
Please ensure that the led profile spotlight is hung using the appropriate "C" clamp or half
cheeseboro. A safety chain or cable should also be used as a secondary point of holding the
fixture in case the clamp comes loose. Never hang the fixture without a safety chain or cable.
There is an eye-bolt on the back of the fixture to which the safety chain or cable can threaded
through and then hung from the secondary point.
9
10

16
If you are not qualified or have any doubts about hanging the led profile spotlight then do NOT
hang it.
Do not clamp the safety cable to the U bracket or clamp. That is not a secondary safety point.
A secondary safety point is any point that will adequately hold the led profile spotlight if the "C"
clamp or half cheesboro fails.
Then the safety cable would be the backup and stop the fixture from falling to the ground. So do
NOT fix the safety cable to the same place that the "C"clamp is attached
Safety Clamp
Safety Cable
11
Floor Projection
Floor Projection

17
Cleaning and maintenance
Now ignoring maintenance and cleaning is very good way of creating problems "down the road"
and many companies and installations do just that. However the net result is, no matter what the
fixture, premature failure!
Changing the oil in a car, most people do on a regular basis.
So with the fixtures, regular maintenance it an excellent practice, if you want the fixtures to last.
So what is the maintenance for the fixture?
Clean the light!
Turn off the led profile spotlight.
Using a small vacuum cleaner, suck the dust and “fur balls” out.
Do not use a can of co². That will just blast the dust and dirt everywhere!
The front lens should be cleaned so the light output is maintained.
The shutter blades sometimes require cleaning as well.
With the led profile spotlight turned off, use only a moist lint-free cloth. Never use alcohol or
solvents to clean the fixture.
Never spray anything onto the fixture at the front or in any place on the fixture.