Toro 114-9577 User manual

FormNo.3360-408RevA
HardstopKit
forMulti-Pro®TurfSprayersandWorkman®200SpraySystem
ModelNo.114–9577
InstallationInstructions
Safety
SafetyandInstructionalDecals
Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaof
potentialdanger.Replaceanydecalthatisdamagedorlost.
114-9576
1.Pinchpoint,hand—keephandawayfromhinge.
©2008—TheToro®Company
8111LyndaleAvenueSouth
Bloomington,MN55420
Registeratwww.Toro.com.OriginalInstructions(EN)
PrintedintheUSA.
AllRightsReserved

Installation
LooseParts
Usethechartbelowtoverifythatallpartshavebeenshipped.
ProcedureDescriptionQty.Use
1Nopartsrequired–Preparethemachine.
2Nopartsrequired–Drilltheboom.
Bracket2
Bumper2
Bolt(5/8x5inches)2
Nut(5/8inch)2
Bolt(5/16x1inch)8
Nut(5/16inch)8
3
Decal114-95762
Installthestops.
4Nopartsrequired–Adjusttheboomstolevel.
Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.
1
PreparingtheMachine
NoPartsRequired
Procedure
Positionthemachineonalevelsurface,stoptheengine,
andengageparkingbrake.
Raisetheboomsintothetransportpositionandremove
theignitionkey.
Ifyouleavethekeyintheignitionswitch,
someonecouldaccidentlystarttheengineand
seriouslyinjureyouorotherbystanders.
Removethekeyfromtheignitionswitchbefore
youdoanymaintenance.
2

2
DrillingtheBoom
NoPartsRequired
Procedure
1.MeasureandmarktheholesshowninFigure1.
Usetheatedgesoftheboomforthemeasurements.
Whenallholesaremarked,usethebracket
Note:Whenallholesaremarkedthebracketcanbe
usedtoverifyproperspacingpriortodrilling.
Figure1
1.2inches4.3.625inches
2.2.27inches5.drill0.375(3/8)inch
diameterhole
3.0.78inch
2.Drilltheholeswheremarked.Theholesshould
0.375or3/8ofaninchindiameter.
3
InstallingtheStops
Partsneededforthisprocedure:
2Bracket
2Bumper
2Bolt(5/8x5inches)
2Nut(5/8inch)
8Bolt(5/16x1inch)
8Nut(5/16inch)
2Decal114-9576
Procedure
1.AssemblethestopsasshownFigure2.Handtighten
onlyatthistimetoallowforlateradjustment.
Figure2
1.Bolt(5/8x5inches)4.Bumper
2.Bracket5.Assembled
3.Nut(5/8inch)
2.Installthestopstotheframeusing4bolts(5/16x1
inch)andnuts(5/16inch)asshownin(Figure3).
3

Figure3
Rightsideshown
1.Centerboomasssemlby4.nuts(5/16inch)
2.Assembledbracketand
bumper
5.Decal
3.Bolt(5/16x1inch)
3.Installadecal114-9576asshowninFigure3.
4
AdjustingtheBoomstoLevel
NoPartsRequired
Procedure
1.Attheoperator’sposition,turntheignitionkeyto
Ontoenergizethesystem.
2.Movetheboomsintopositionsothattheyarelevel
withtheground.
3.Removethekeyandexittheoperator’sposition.
4.Atthehinge,adjustthepositionofthebumpersso
theboomcannotmovepastlevelwiththeground.
Takecaretomakesurethebumperislevel.
5.Tightentheboltandnuttolockthebumpersintothe
adjustedposition.Torquethefastenersto135-165
ft-lbs(183-223N-m).
Note:Thebumpermayexperiencesomecompression
overtime.Iftheboomsdropbelowlevel,usethis
proceduretoreadjustthebumperpositionneeded.
4