Torque TANK MX User manual

TANK MX ASSEMBLY GUIDE
PART #: 5672701-B
VERSION: XTTMX-RPH-101

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
ITEM PART NUMBER DESCRIPTION QTY
1 5637101 ASSY, FRAME-MX 1
2 5632401 WHEEL, 13" DIA X 5.0" WIDE 4
3 2011201 WASHER, STEEL 12.7 ID-40 OD-4 THK CLEAR ZINC 4
4 2010901 WASHER, LOCK M12 SAE ST ZN 12
5 2011301
SCREW, M12-1.75 X 30L SOC HD GR 12.9 CLEAR ZINC
4
6 5641001 ASSY, HANDLES AND HOOP MODULE 2
7 2010801 WASHER, STEEL 12.7 ID-25 OD-2 THK CLEAR ZINC 8
8 2010701 SCREW, M12-1.75 X 85L SOC HD GR 12.9 CLEAR ZINC 8
9 56314PA PTD ASSY, PUSH HANDLE-RIGHT 2
10 56315PA PTD ASSY, PUSH HANDLE-LEFT 2
11 56024PA PTD ASSY, TANK WEIGHT HORN (OPTIONAL) 2
12 56363PA PTD ASSY, ALIGNMENT DEVICE (OPTIONAL) 2
13 2024001 SCREW, M10-1.5 70L SOC HD GR 12.9 CLEAR ZINC (OPTIONAL) 8
14 57665PA PTD ASSY, WHEELBARROW HANDLE, RIGHT (OPTIONAL) 1
15 57664PA PTD ASSY, WHEELBARROW HANDLE, LEFT (OPTIONAL) 1
2
TABLE OF CONTENTS:
TANK MX ASSEMBLY: PAGES 3 - 6 •
WEIGHT HORN KIT (OPTIONAL): PAGES 7 - 8 •
WEIGHT HORN STACKING KIT (OPTIONAL): PAGES 9 - 10 •
WHEELBARROW ATTACHMENT (OPTIONAL): PAGE 11 •
TANK MX HANDLE ADJUSTMENTS: PAGE 12 •
TANK MX HANDLE STORAGE AND STACKING: PAGES 13 - 14 •
TANK MX RESISTANCE ADJUSTMENTS: PAGE 15 •
INSPECTION & LUBRICATION: PAGE 16 •
SAFETY AND WARNING NOTICES: PAGE 17 •
TOOLS NEEDED FOR ASSEMBLY:
10MM ALLEN WRENCH (INCLUDED) •
6MM ALLEN WRENCH (INCLUDED) •
AIR PUMP WITH GAUGE •
PHILLIPS SCREW DRIVER •

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
1
23
4
5
NOTE:
Before assembling Tires, check
Tire pressure. Make sure Tires
are inflated to 30 PSI
NOTE:
Align Groove in Hub with
Cross Pin in Axle (4X)
3
NOTE:
SECURELY tighten all bolt connections in this step.
STEP 1

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
Pull Spring Pin and rotate
Handle up 180 degrees
6
4
NOTE:
Repeat this step for the other COMBO HANDLE.
STEP 2

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
1
6
8
47
NOTE:
After this step is complete,
pull Spring Pin and rotate
Handle down 180 degrees (2X)
6
5
NOTE:
SECURELY tighten all bolt connections in this step.
STEP 3

10
9
9
10
1
NOTE
Align "L" Label on the Left Handle
With "L" Label on Receiver.
(Repeat this step for other Left Handle)
NOTE
Align "R" Label on Right Handle
with "R" Label on Receiver.
(Repeat this step for other Right Handle)
6
STEP 4

Loosen and remove (8) Bolts,
(16) Flat Washers and (8) Nuts
Loosen (4) side Bolts
but DO NOT
remove
XTWHK
WEIGHT HORN KIT (OPTIONAL)
STEP 1
7
NOTE:
Handles have been hidden for assembly clarity.

1
11
SECURELY assemble (2) Weight Horns
using the (8) Bolts, (16) Flat Washers
and (8) Nuts from previous step
SECURELY tighten
side Bolts (4X)
NOTE:
SECURELY tighten all bolt connections in this step.
Handles have been hidden for assembly clarity.
8
XTWHK
WEIGHT HORN KIT (OPTIONAL)
STEP 2

NOTE :
Discard these (8) Bolts.
Bolts will be replaced
Loosen (4) side Bolts
but DO NOT
remove
Loosen and remove (8) Bolts,
(16) Flat Washers and (8) Nuts
XTWHSK
WEIGHT HORN STACKING KIT (OPTIONAL)
STEP 1
9
NOTE:
Handles have been hidden for assembly clarity.

1
11
12
13
SECURELY assemble (2) Weight
Horns and (2) Alignment Cups to
TANK using (8) NEW
Bolts, (16) Flat
washers and (8) Nuts from previous step
SECURELY tighten
side Bolts (4X)
NOTE:
SECURELY tighten all bolt connections in this step.
Handles have been hidden for assembly clarity.
10
XTWHSK
WEIGHT HORN STACKING KIT (OPTIONAL)
STEP 2

NOTE
Match "L" Label on Left
Wheelbarrow handle with
"L" Label on Rear Frame
NOTE
Match "R" Label on Right
Wheelbarrow Handle with
"R" Label on Rear Frame
14
15
6
11
WHEELBARROW HANDLE ATTACHMENT (OPTIONAL)

HANDLE DOWN: STORAGE POSITION
COMBO
HANDLE
HANDLE HORIZONTAL: LIFTING POSITION AND PUSHING POSITION
COMBO
HANDLE
HANDLE UP: TOWING POSITION AND PUSHING POSITION
Attach Tow
Straps here (2X)
COMBO
HANDLE
Pull Spring Pin
to rotate Handle
12
XTTMX HANDLE POSITIONS

Remove Left and Right Push
Handles and gently place them
inside the Tray of the TANK
10
9
10
9
13
XTTMX STORAGE/STACKING
STEP 1

11
12
COMBO HANDLE
NOTE:
Make sure Receivers
are seated SECURELY
over Weight Horns (2X)
14
XTTMX STORAGE/STACKING
STEP 2
NOTES:
Use two people to lift TANKS.
Use COMBO HANDLES to stack tanks on top of each other.
Make sure both RECEIVERS on the bottom of the TANK are
seated securely over the WEIGHT HORNS on top of the TANK (see inset).
DO NOT
stack the TANKS more than three high.

POSITION 3: HARD RESISTANCE
POSITION 2: MEDIUM RESISTANCE
POSITION 1: LOW RESISTANCE
POSITION N: NEUTRAL
NOTE:
ENGAGING THE MX MODE WILL INCREASE THE
RESISTANCE AT ANY LEVEL N - 3. RESISTANCE
INCREASES APPROXIMATELY 30% AT LEVEL 3
15
XTTMX RESISTANCE ADJUSTMENT & MX MODE

16
#TorqueFitness #TorqueTANK
https://www.instagram.com/torquefitnessusa/
https://www.youtube.com/c/TorqueFitness
https://www.facebook.com/groups/thetankcommunity
INSPECTION & LUBRICATION
INSPECTION:
ATTENTION:
PLEASE ENSURE THAT ALL TIRES ARE INFLATED
TO 30 PSI. FAILURE TO DO SO MAY RESULT IN
TANK VEERING DURING USE.
Once a month, check for loose bolts on handles, wheels and
weight horns (optional) as indicated. Tighten if necessary.
Once a month, check that the chain and sprockets are
clean, free of rust, dust and grime. Make sure that the
chain is properly lubricated.
Once a month, inspect belt. Make sure the belt is not
worn, frayed or loose. Replace belt if worn or frayed.
LUBRICATION :
Once a month, the sprockets should be cleaned and the chain
should be lubricated.
RECOMMENDED LUBRICATION: Use a Dry lubrication for indoor
use, and wet lubrication for outdoor use. Most bicycle shops carry a
variety of different lubricants and can recommend a lubricant based
on the conditions where the TANK will be used.

17
IMPORTANT SAFETY INSTRUCTIONS:
WARNING:
The safety of this product can be maintained only if it is examined regularly for damage
and wear. See inspection and lubrication section on page 16 for more details.
DO NOT overinflate tires! All tires should be inflated to 30 PSI. Check air pressure periodically. •
Keep children away from the TANK MX during use. •
Keep all loose clothing, hair and shoelaces away from moving parts. •
DO NOT attempt to use the TANK MX for any purposes other than that for which it was intended. •
Wear shoes with rubber or high-traction soles. High heels, dress shoes, sandals or bare feet are •
not suitable for use with the TANK MX.
DO NOT drop the weight plates onto the TANK MX. Doing so, may result in damage to the TANK MX. •
DO NOT use the TANK MX in wet or slippery conditions. •
DO NOT push the TANK MX while any accessories are attached to the push/pull bar. •
DO NOT stand or ride on the TANK MX1. •
DO NOT use the TANK MX without the shrouds. •
Torque Fitness
11201 Xeon Street NW Ste 101
Coon Rapids, MN USA 55448
www.torquefitness.com
Toll free: 1-877-867-7835
or 763-754-7533 (8:30 am – 5:00 CST).
For sales: [email protected]
For service: [email protected]