Torque XCREATE-LPDWM User manual

4 FT (1.2 M) LAT PULLDOWN WALL MOUNT
ASSEMBLY INSTRUCTIONS
PART # 5701101-A VERSION: XCREATE-LPDWM

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
ITEM PART NUMBER DESCRIPTION QTY
1 56641PA PTD ASSY, LOWER WALL MOUNT 1
2 5645301 WLDMT, LAT BASE 1
3 2001301 WASHER, FLAT 1/2 SAE ST ZN 12
4 2006803 BOLT, 1/2-13 X 1" (25mm) SOCKET HEAD W/NP 6
5 2001101 WASHER, FLAT 3/8 SAE ST ZN 8
6 56468PA PTD ASSY, LAT FRONT UPRIGHT 1
7 2005815 BOLT, 1/2-13 X 4" (102mm) SOCKET HEAD 2
8 2001401 NUT, 1/2-13 LK ST ZN 3
9 5513601 CUSHION, WEIGHT STACK 2
10 5643201 GUIDE ROD, 19 DIA X 1912 2
11 56351PA PTD ASSY, 20 LB WEIGHT PLATE 5
12 56350PA PTD ASSY, 15 LB WEIGHT PLATE 10
13 56345PA PTD ASSY, HEAD PLATE 1
14 5095301 SHAFT COLLAR, GUIDE ROD 2
15 5667301 BUSHING, GUIDE ROD RETAINER 2
16 55181PA PTD ASSY, WEIGHT SELECTOR STORAGE PLATE 1
17 2009402 BOLT, 3/8-16 X 3/4" (19mm) ST HT SOCKET HEAD W/NP 6
18 5664401 WLDMT, UPPER WALL MOUNT 1
19 56459PA PTD ASSY, LAT TOP BOOM 1
20 2009418 BOLT, 3/8-16 X 4-3/4" (121mm) ST HT SOCKET HEAD W/NP 2
21 5675301 LABEL, WEIGHT STACK 15-265 LB (6.8-120.2 KG) 1
22 56475PA PTD ASSY, KNEE HOLD DOWN 1
23 2005821 BOLT, 1/2-13 X 5-1/2" (140mm) SOCKET HEAD 1
24 5454901 PAD, TAPPERED SEAT 1
25 2009404 BOLT, 3/8-16 X 1-1/4" (32mm) ST HT SOCKET HEAD W/NP 2
26 5662501 WLDMT, LEFT SHROUD BASE 1
27 5662901 WLDMT, RIGHT SHROUD BASE 1
28 5645101 SHROUD, XCREATE CABLE STATION 2
29 5664701 SHROUD, TOP CAP 1
30 2002101 WASHER, FLAT 1/4 SAE ST ZN 8
31 2006502 BOLT, 1/4-20 X 1/2" (13mm) SOCKET HEAD W/NP 6
32 5676201 PLACARD, XCREATE-LPD-101 1
33 5581301 COVER, FRONT BASE 1
34 2005509 BOLT, 1/4-20 X 3/8" (9mm) SOCKET HEAD 2
35 5674701 ASSY, ALUMINUM LAT BAR 1
36 5091801 SNAP HOOK, 8MM DIA X 80MM 1
2
NOTE:
Anchoring hardware is dictated by the wall construction that the station
is being attached to. See pages 4 and 13 for the requirements.
If multiple stations are going to be attached to the same wall, a minimum
of 4' (2.4 M) center to center is recommended between stations.
For assistance, contact [email protected] or call
[phone]; Toll free in USA [phone].
TOOLS FOR ASSEMBLY:
3/8" ALLEN WRENCH •
5/16" ALLEN WRENCH •
3/16" ALLEN WRENCH •
3/4" WRENCH OR SOCKET •
9/16" WRENCH OR SOCKET •
1/2" WRENCH OR SOCKET •
RUBBER MALLET •

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
LOWER WALL MOUNT
LAT BASE
1/2 X 1" BOLT (2)
1/2" FLAT WASHER
NOTE:
BEFORE TIGHTENING BOLTS, MAKE SURE
THAT THESE TWO SURFACES ARE FLUSH
3
STEP 1
NOTES:
SECURELY tighten bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
LOWER WALL MOUNT
3/8" FLAT WASHER (4)
3/8" LAG BOLT (4)
(TYPICAL FOR
WOOD STUDS)
3-1/16"
(7.8 CM)
2-1/2"
(6.4 CM)
16"
(40.6 CM)
NOTE:
MAKE SURE THE LOWER
WALL MOUNT IS LEVEL
NOTE:
BEFORE ANCHORING LOWER WALL
MOUNT TO THE WALL, ADJUST
LEVELERS (2) SO THAT THE BASE
PLATE IS LEVEL WITH THE FLOOR.
WALL
BASE PLATE
WARNING:
THE LOWER WALL MOUNT MUST BE ANCHORED TO THE
WALL USING FOUR WALL ANCHORS SUITABLE FOR THAT
PATICULAR WALL CONSTRUCTION.
STEP 2
4
NOTES:
The images shown above is the anchoring hardware used for attaching
to typical walls with wood studs spaced 16" on center. The anchors
used will depend on the wall construction. In all cases, all four
anchoring locations must be used. The pull-out strength of the
anchoring bolts used must be greater than or equal to 200lbs. (91kg)
SECURELY tighten bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
3/8" FLAT WASHER (2)
3/8 X 4-3/4"
BOLT (2)
LAT BASE
LOWER WALL MOUNT
5
STEP 3
NOTES:
SECURELY tighten bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
LEFT SHROUD BASE
3/8" X 3/4" BOLT (2)
LOWER WALL MOUNT
3/8" FLAT WASHER (2)
6
STEP 4
NOTES:
SECURELY tighten bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
LOWER WALL MOUNT
RIGHT SHROUD BASE
3/8" FLAT WASHER (2)
3/8 X 3/4" BOLT (2)
7
STEP 5
NOTES:
SECURELY tighten bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
LAT BASE
LAT FRONT UPRIGHT
1/2 X 4" BOLT (2)
1/2" FLAT WASHER (4)
1/2" LOCK NUT (2)
8
STEP 6
NOTES:
LOOSELY tighten bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
LAT BASE
WEIGHT STACK CUSHION (2)
15 LB WEIGHT PLATE (10)
HEAD PLATE
GUIDE ROD (2)
SHAFT COLLAR (2)
GUIDE ROD RETAINER (2)
20 LB WEIGHT PLATE (5)
NOTE:
INSERT GUIDE RODS THROUGH THE LAT
BASE AND DOWN TO TOP OF BOLTS
9
STEP 7

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
WEIGHT SELECTOR
STORAGE PLATE
HEAD PLATE
3/8 X 3/4" BOLT (2)
STEP 8
10
NOTES:
SECURELY tighten bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
1/2 X 1" BOLT (2)
1/2" FLAT WASHER (2)
LAT TOP BOOM
UPPER WALL MOUNT
11
STEP 9
NOTES:
SECURELY tighten bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
LAT TOP BOOM
LAT FRONT UPRIGHT
1/2 X 1" BOLT (2)
1/2" FLAT WASHER (2)
12
STEP 10
NOTES:
LOOSELY tighten bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
UPPER WALL MOUNT
3/8" FLAT WASHER (4)
3/8" LAG BOLT (4)
(TYPICAL FOR
WOOD STUDS)
80"
(203.2 CM)
2-1/2"
(6.4 CM)
16"
(40.6 CM)
NOTE:
MAKE SURE THE UPPER
WALL MOUNT IS LEVEL
WARNING:
THE UPPER WALL MOUNT MUST BE
ANCHORED TO THE WALL USING FOUR
WALL ANCHORS SUITABLE FOR THAT
PATICULAR WALL CONSTRUCTION
13
STEP 11
NOTES:
The images shown above is the anchoring hardware used for attaching
to typical walls with wood studs spaced 16" on center. The anchors
used will depend on the wall construction. In all cases, all four
anchoring locations must be used. The pull-out strength of the
anchoring bolts used must be greater than or equal to 200lbs. (91kg)
SECURELY tighten bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
GUIDE ROD RETAINER (2)
SHAFT COLLAR (2)
LAT TOP BOOM
GUIDE ROD (2)
NOTE:
SLIDE THE GUIDE ROD RETAINERS UP INSIDE THE
LAT TOP BOOM. SLIDE THE SHAFT COLLARS UP INSIDE
OF THE GUIDE ROD RETAINERS AND SECURELY
TIGHTEN THE SET SCREWS OF THE SHAFT COLLARS
SECURELY TIGHTEN
THIS BOLT CONNECTION
SECURELY TIGHTEN
THIS BOLT CONNECTION
14
STEP 12
NOTES:
SECURELY tighten bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
NOTE:
THE HOUSING ON THE CABLE SHOULD BE AT
LEAST 1/2" AWAY FROM THE SWIVEL PULLEY.
IF THE HOUSING IS TOUCHING THE SWIVEL
PULLEY, THEN THE CABLE NEEDS TO BE
ADJUSTED. LOOSEN JAM NUT AND TURN THE
THREADED END OF THE CABLE COUNTER
CLOCKWISE UNTIL THE HOUSING IS 1/2" AWAY
FROM THE SWIVEL PULLEY. SECURELY
TIGHTEN JAM NUT.
THREADED END
STEM
JAM NUT
HEAD PLATE
STORAGE FOR WEIGHT
STACK SELECTOR PIN
HOUSING
SWIVEL
PULLEY
NOTE:
ATTACH THE WEIGHT STACK
LABELS TO THE WEIGHT STACK
STARTING WITH THE HEAD
PLATE
NOTE:
THREAD THE CABLE END INTO THE
STEM OF THE HEAD PLATE UNTIL
THE HOUSING IS APPROXIMATELY
1/2" AWAY FROM THE SWIVEL PULLEY,
THEN SECURELY TIGHTEN THE JAM
NUT. SEE NOTE ABOVE
15
STEP 13
NOTES:
SECURELY tighten connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
LAT FRONT UPRIGHT
KNEE HOLD DOWN
1/2 X 5-1/2" BOLT
1/2" FLAT
WASHER (2)
1/2" LOCK NUT
NOTE:
PULL SPRING PIN OUT TO
ASSEMBLE THE KNEE HOLD
DOWN. RELEASE THE SPRING
PIN INTO THE DESIRED HOLE
ON THE LAT FRONT UPRIGHT
SPRING PIN HOLE
16
STEP 14
NOTES:
SECURELY tighten bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
TAPERED SEAT
3/8" FLAT WASHER (2)
3/8" X 1-1/4" BOLT (2)
LAT BASE
17
STEP 15
NOTES:
SECURELY tighten bolt connections in this step.

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
RIGHT SHROUD BASE
LEFT SHROUD BASE
FRONT SHROUD (2)
TOP VIEW LEFT
NOTE:
MAKE SURE SHROUD IS
SEATED BETWEEN THE
SHROUD SUPPORT AND
THE FOUR TABS AS SHOWN
TOP VIEW RIGHT
NOTE:
MAKE SURE SHROUD IS
SEATED BETWEEN THE
SHROUD SUPPORT AND
THE FOUR TABS AS SHOWN.
18
STEP 16

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
UPPER WALL MOUNT
TOP CAP
FRONT SHROUD
(RIGHT SIDE)
FRONT SHROUD
(LEFT SIDE)
1/4" FLAT WASHER (4)
1/4 X 1/2" BOLT (4)
NOTE:
MAKE SURE INTERNAL GROOVES OF
THE TOP CAP FIT DOWN OVER THE
TOP EDGES OF BOTH FRONT SHROUDS.
19
NOTES:
LOOSELY tighten bolt connections in this step.
STEP 17a

50 180
3
190150 170160
6
130 14012090 110100403010 706020 80
1 2 4 5 7
200
TOP CAP
TOP BOOM
1/4" FLAT WASHER (2)
1/4 X 1/2" BOLT (2)
20
STEP 17b
NOTES:
SECURELY tighten bolt connections in this step, and previous step.