Town & Country Fireplaces TC30 Black Diamond User manual

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
These instructions are supplementary to the Installation and
Operating Instructions supplied with the replace and should be kept
together.Refer to the Installation and Operating Instructions for proper
gas supply, safety requirements and operating instructions
130623-16 22150009 100005906
TC30
HEARTWOOD
BURNER INSTALLATION
INSTRUCTIONS
SKU# 22150009
FOR TC30 Series D
Fireplaces
Visit www. townandcountryfireplaces.net for the most recent version of this manual

Contents of Package
100005906
2
SKU# 22150009 130623-16
• BURNER ASSEMBLY
(including pilot and manifold)
• LOG GRATE
• TC30 HEARTWOOD LOGS
• EMBER MATERIAL
• HARDWARE PACKAGE
• COAL CHUNKS
• VERMICULITE
If this replace is to be
used on Propane please
convert prior to installtion.
See pages 10 – 12.
Burner Installation
1. Place the keyhole slots in the burner
over the two screws located in the rebox
base. (Fig. #1 & 1a)
2. Slide the burner back to engage the
screws in the small part of the keyhole
slot and tighten screws. (Fig. #1b)
3. Remove access cover from side of
rebox(Fig. #1c)
Fig. # 1a
Fig. # 1b
SCREWS
Fig. # 1
Fig. # 1c

100005906
SKU# 22150009 130623-16
3
Ignition wire (red)
Flame sensor
wire (white)
Interface module
Ignition and sensor wires
Bulkhead plate
Fig. # 2
Burner/ Grate Installation
Fig. # 3
4. Feed the ignition and sensor wires through
the bulkhead plate (Fig.#2) to the interface
module. (Fig.#3).

100005906
4
SKU# 22150009 130623-16
Gas and pilot supply tubes
Bulkhead plate
Fig. # 4
5. Attach the pilot and gas supply tubes to
the bulk head tting and tighten.
(Fig. # 3b) Ensure the connections are
gas tight. Conceal the spark and
sensor wires below the supply tubes.
A panel set must now be installed. See
Installation and Operating Instructions
manual for details.
6. Position the slots of the grate securing
brackets over the holes in the oor shield
and secure with the two screws
(Fig. # 4).
Fig. # 3b

100005906
SKU# 22150009 130623-16
5
Note:
Ember material placement
and amount will affect
ame appearance.
More ember material
results in lower ame
height.
Add or remove as needed
until desired ame affect.
Reduce the amount used
on Propane models, as too
much will create soot
Fig. #5
Ember Material
Fig. #6
A large bag of ember material is shipped with the replace and needs to be installed on
the burner to ensure optimum performance and ame appearance. A bag of coal chunks
and vermiculite is also supplied this must only be used around the burner pan to cover
up the gas lines and brackets.
1. Pull apart the material into ember size pieces (approximately 1” square) and
gently place them into the burner pan. Do not compress, leave them loose for best
performance.
2. Fill the burner pan with embers until level with the top of the pan at rear, and gradually
slope forward to the rebox oor at the front, covering both burner tubes.
3. Place remaining ember material, coal chunks and vermiculite outside of the burner
pan as desired to cover-up gas lines and brackets. Do not put coal chunks or
vermiculite inside burner pan as this will cause sooting and the burner to
malfunction.
Embers only in this area.Embers only in this area.
Embers, coal chunks and vermiculite.Embers, coal chunks and vermiculite.

100005906
6
SKU# 22150009 130623-16
Gas plumbing and vent connections
should be completed before proceeding.
The logs are fragile, and should be handled
with care. Unpack and inspect log set.There
should be a total of seven logs.
Position the logs as indicated by the following
pictures.The seven main logs have holes and /
or pins.Engage each pin in the corresponding
holes. The remaining two logs do not have
holes or pins. They rest in position. Locate
as per the diagrams (g. # 7-15)
Note: Improper placement of logs
will cause sooting on internal parts
and glass. The logs may need to be
repositioned slightly to avoid excessive
ame impingement.
Log Placement
Fig. # 7
Fig. # 8
BASE LOG, #1
LEFT CENTER LOG, #2

100005906
SKU# 22150009 130623-16
7
Fig. #9
Fig. #10
LEFT FRONT LOG, #3
LOG WITH HOLE, #4

100005906
8
SKU# 22150009 130623-16
Fig. #11
Fig. #12
RIGHT CENTER LOG, #5
FRONT RIGHT LOG, #6

100005906
SKU# 22150009 130623-16
9
FRONT RIGHT LOG, #6
Fig. #14
Fig. #15
Fig. #13
CENTER TWIG, #8
RIGHT BASE LOG, #7
CENTER BASE CHUNK, #9

Propane Conversion
If the unit is to be used on propane,
convert as follows using the compo-
nents supplied with this replace:
Note: Factory supplied components must
be used to ensure correct input.
After conversion conrm proper manifold
pressure.
CAUTION
The gas supply and electrical power
must be shut off before proceeding
with the conversion.
Fig. # 17
Fig. # 18
Fig. # 16
WARNING
This conversion kit shall be
installed by a qualied
service agency in
accordance with the
manufacturer's instructions
and all applicable codes
and requirements of the
authority having
jurisdiction.
If the information in these
instructions is not followed
exactly, a re, explosion or
production of carbon
monoxide may result
causing property damage,
personal injury or loss of
life.
The qualied service
agency is responsible for
the proper installation of
this kit.
The installation is not
proper and complete un-
til the operation of the
converted appliance is
checked as specied in the
manufacturer's instructions
supplied with the kit.
1. Ensure the burner, pilot and gas
supply are turned off, and the
appliance has cooled.
2. Remove the two screws securing the
manifold assembly to the burner.
(Fig. #16)
3. Remove the manifold assembly from the
burner. (Fig. #17)
4. With a ½”wrench remove the natural gas
orice and replace with propane orice
(1.9 mm) (our part # 5022.76)
(Fig. #18)
5. Fully open the primary air shutter.
6. Reinstall the manifold assembly and
air deector.
MAIN BURNER (1.90 mm)
ORIFICE (LE)
100005906
10
SKU# 22150009 130623-16

7. With a 7/16” wrench loosen the pilot head
on the pilot assembly by a half-turn
(Fig. #19)
Fig. #21
Fig. # 19
Fig. # 20
8. Slide the pilot adjustment band
over and ensure that the hole in
the orice band is showing. (Fig.
#20 shows NG position,
Fig. # 21 shows LP position)
Cet appareil a été converti en gaz propane
Numéro d'assemblage
j m a
Firme
Adresse
l'entreprise désignée
ci-dessus accepte la
responsabilité que cette
conversion a été
correctement faite.
Kit Number
dd mm yy
Company
Address
The above accepts the
responsibility that this
conversion has been
properly performed.
This appliance was converted to propane gas
5052.52001-B
5052.52001-B
For complete valve installation instructions, refer to the
instruction book included in the SIT conversion kit.
NG Position (Fig#20)
LP Position (Fig #21)
100005906
SKU# 22150009 130623-16
11
Minimum
rate screw
HOLE
9. Fill in the conversion label. Peel off
the protective backing and apply the
conversion label directly over the gas
specications on the rating label.

100005906
12
SKU# 22150009 130623-16
1. Remove the plug from the manifold test
port. The plug is located between the
right side lintel and rebox side (bottom
port). (Fig. # 22)
2. Thread the extension test tting into the
open test port. (Fig. #23)
3. Attach a pressure gauge onto the
tting.
4. When testing is complete remove the
extension test tting and replace the
plug. Thread sealant will be required to
ensure a gas-tight connection.
Correct gas pressure requirement:
Supply Pressure Natural Gas Propane
(For purpose of input adjustment)
Minimum 5.0" WC 12.5" WC
Maximum 13.9" WC 13.9" WC
Manifold Pressure
Maximum 3.5" WC 10.0" WC
Minimum 1.6" WC 6.4" WC
Note:To test the gas pressure, turn off the gas supply before removing the plug from
the supply pressure test port or manifold pressure test port.
Verify gas pressures with the replace lit and on the highest setting.
Fig #22
Fig #23
Gas Pressure Check
SUPPLY MANIFOLD

100005906
SKU# 22150009 130623-16
13
Fig. # 24
The air shutter on the burner tube controls the primary combustion air to the gas burner and is preset at the factory for natural gas fuel.
Some adjustment may be necessary to obtain desired ame and to eliminate carbon deposits. Evaluate ame appearance after the
replace has reached operating temperature. See Fig. #24 for proper ame pattern.
Open primary air shutter if the logs, glass, and rebox have carbon accumulation and / or the ames are long, dark and stringy. The shutter
may also be opened to enhance the Ember Material glow and lessen the ame height.
For Propane, start with the air shutter fully open and adjust to decrease air if needed.
Caution: Burner area may be hot!
Turn off the replace and allow the unit to cool before proceeding.
Caution: Proper air shutter setting is a
must.
The ame should be just orange and “lazy”.
It should NEVER be set to create sooting on
internal parts and glass.
Flame Adjustment
To Adjust:
1. Open and remove window frame and set
aside. See "Window Frame Removal"
section found in the Installation and
Operating Instructions manual.
2. Remove the log set and set aside.
3. Loosen the screw in the Primary
Air Shutter.
4. Rotate the shutter to increase or decrease
the amount of primary air.Fully closed for
natural gas and fully open for propane
gas.
5. Reassemble in reverse order.
Fig. # 25
PRIMARY AIR SHUTTER

100005906
14
SKU# 22150009 130623-16
Replacement Parts
ITEM.......DESCRIPTION................................................... PART NO.
#1..........HEARTWOOD BURNER ASSEMBLY..22150009
#2..........HEARTWOOD LOG SET......................5094.302318
#3..........ORIFICE, NATURAL GAS (#32)...............5021.332A
ITEM.......DESCRIPTION.....................................................PART NO.
#4..........PILOT ASSEMBLY.............................TCRP.5005025
#5..........MAIN SUPPLY TUBE (FLEX)............. ........5019.223
*#6..........PROPANE CONVERSION KIT............TC30.DLPKIT
#1.... BURNER ASSEMBLY
1a GRATE
1b BURNER INSULATION
1c BURNER TRAY SUPPORT SHIELD
1d PILOT SHIELD
1e TC36.NG01 BURNER WELD
1f MANIFOLD
1g 1/2 PIPE TO 1/2 TUBE CONNECTION
1h PILOT BRACKET
KIT CONTENTS:
#2.... 9 PCS HEARTWOODLOG SET
EMBER MATERIAL (Not shown)
1 BASE LOG
2 LEFT CENTER LOG
3 LEFT FRONT LOG
4 LOG WITH HOLE
5 RIGHT CENTER LOG
6 FRONT RIGHT LOG
7 RIGHT BASE LOG
8 CENTER TWIG
9 CENTER BASE CHUNK
#3.... ORIFICE, NATURAL GAS (#32)
#4.... PILOT ASSEMBLY, CONVERTIBLE
(INCLUDING TUBE)
#5.... MAIN SUPPLY TUBE (FLEX)
#6.... PROPANE CONVERSION KIT (Not shown)
(WHEN ORDERING, INCLUDE PART NUMBER WITH DESCRIPTION)
1
2
3
4
7
5
6
8
9
#1
#2 #3
#4
#5
1a
1b
1e
1d
1f
1h
1c 1g
*NOT SHOWN

100005906
SKU# 22150009 130623-16
15

© 2016 Copyright Pacic Energy Fireplace Products LTD
Reproduction, adaptation, or translation
without prior written permission is prohibited,
except as allowed under the copyright laws.
For technical support, please contact your retailer.
www.townandcountryreplaces.net
2975 Allenby Rd., Duncan, BC V9L 6V8
Printed in Canada