Town & Country Fireplaces TC36 User manual

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.
These instructions are supplementary to the Installation and
Operating Instructions supplied with the replace and should be kept
together.Refer to the Installation and Operating Instructions for proper
gas supply, safety requirements and operating instructions
050411-16 TC36.NG05C 5056.427C45
TC36
HEARTWOOD
BURNER INSTALLATION
INSTRUCTIONS
PART#
TC36.NG05C
FOR TC36 & TC36 AR
Series C

Contents of Package
If this replace is to be
used on Propane please
convert prior to installtion.
See pages 10 – 12.
2
TC36.NG05C 050411-16
• BURNER ASSEMBLY
(including pilot and manifold)
• LOG GRATE
• TC36 HEARTWOOD LOGS
• EMBER MATERIAL
• HARDWARE PACKAGE
• COAL CHUNKS
• VERMICULITE
Burner Installation
1. Place the keyhole slots in the burner
over the two screws located in the rebox
base. (Fig. #1 & 1a)
2. Slide the burner back to engage the
screws in the small part of the keyhole
slot and tighten screws. (Fig. #1b)
3. Remove access cover from side of
rebox(Fig. #1c)
Fig. # 1a
Fig. # 1b
SCREWS
Fig. # 1
Fig. # 1c

BULKHEAD PLATE
2 SCREWS
4. Secure the electrical bulkhead plate and
gasket to the rebox. (2 screws) Attach the
ignition and sensor wires to the module.
Red end to the connector marked by the
red dot, white end to the connector marked
by the white dot
Fig.#2 & Fig.#3
Fig. # 2
Burner/ Grate Installation
RED END TO
RED DOT
WHITE END TO
WHITE DOT MODULE
Fig. # 3
3
TC36.NG05C 050411-16

PILOT SUPPLY
TUBE
MAIN GAS SUPPLY
TUBE
Fig. # 4
5. Attach the pilot and gas supply tubes to
the bulk head tting and tighten.
(Fig. # 3b) Ensure the connections are
gas tight. Conceal the spark and
sensor wires below the supply tubes.
A panel set must now be installed. See
Installation and Operating Instructions
manual for details.
6. Position the slots of the grate securing
brackets over the holes in the oor shield
and secure with the two screws
(Fig. # 4).
Fig. # 3b
4
TC36.NG05C 050411-16

Note:
Ember material placement
and amount will affect
ame appearance.
More ember material
results in lower ame
height.
Add or remove as needed
until desired ame affect.
Reduce the amount used
on Propane models, as too
much will create soot
5
TC36.NG05C 050411-16
Fig. #5
Ember Material
Fig. #6
A large bag of ember material is shipped with the replace and needs to be installed on
the burner to ensure optimum performance and ame appearance. A bag of coal chunks
and lava rock is also supplied this must only be used around the burner pan to cover up
the gas lines and brackets.
1. Pull apart the material into ember size pieces (approximately 1” squares) and
gently place them into the burner pan. Do not compress, leave them loose for best
performance.
2. Fill the burner pan with embers until level with the top of the pan at rear, and gradually
slope forward to the rebox oor at the front, covering both burner tubes.
3. Place remaining ember material, coal chunks and lava rock outside of the burner pan
as desired to cover-up gas lines and brackets. Do not put coal chunks or lava rock
inside burner pan as this will cause sooting and the burner to malfunction.
Embers only in this area.
Embers only in this area.
Embers, coal chunks and lava rock.
Embers, coal chunks and lava rock.

6
TC36.NG05C 050411-16
Gas plumbing and vent connections should
be completed before proceeding.
The logs are fragile, and should be handled
with care. Unpack and inspect log set. There
should be a total of seven logs.
Position the logs as indicated by the following
pictures.The seven main logs have holes and /
or pins.Engage each pin in the corresponding
holes. The remaining two logs do not have
holes or pins. They rest in position. Locate as
per the diagrams (g. # 7-15)
Note:Improper placement of logs will cause
sooting on internal parts and glass. The
logs may need to be repositioned slightly
to avoid excessive ame impingement.
Log Placement
Fig. # 7
Fig. # 8
BASE LOG, #1
LEFT CENTER LOG, #2

7
TC36.NG05C 050411-16
Fig. #9
Fig. #10
LEFT FRONT LOG, #3
LOG WITH HOLE, #4

8
TC36.NG05C 050411-16
Fig. #11
Fig. #12
RIGHT CENTER LOG, #5
FRONT RIGHT LOG, #6

9
TC36.NG05C 050411-16
Fig. #14
Fig. #15
Fig. #13
CENTER TWIG, #8
RIGHT BASE LOG, #7
CENTER BASE CHUNK, #9

Propane Conversion
If the unit is to be used on propane,
convert as follows using the
components supplied with this
replace:
CAUTION
The gas supply and electrical power
must be shut off before proceeding
with the conversion.
Fig. # 17
Fig. # 18
Fig. # 16
WARNING
This conversion kit shall be
installed by a qualied
service agency in
accordance with the
manufacturer's instructions
and all applicable codes
and requirements of the
authority having
jurisdiction.
If the information in these
instructions is not followed
exactly, a re, explosion or
production of carbon
monoxide may result
causing property damage,
personal injury or loss of
life.
The qualied service
agency is responsible for
the proper installation of
this kit.
The installation is not
proper and complete un-
til the operation of the
converted appliance is
checked as specied in the
manufacturer's instructions
supplied with the kit.
Note: Factory supplied components must
be used to ensure correct input.
After conversion conrm proper manifold
pressure.
1. Ensure the burner, pilot and gas
supply are turned off, and the
appliance has cooled.
2. Remove the two screws securing the
manifold assembly to the burner.
(Fig. #16)
3. Remove the manifold assembly from the
burner. (Fig. #17)
4. With a ½”wrench remove the natural gas
orice (#30) and replace with propane
orice (#45) (our part # 5021.34)
(Fig. #18)
5. Fully open the primary air shutter.
6. Reinstall the manifold assembly and
air deector.
MAIN BURNER
(#45) ORIFICE (5021.34)
MINIMUM RATE SCREW (5005.015)
CONVERSION LABEL (5052.5208)
10
TC36.NG05C 050411-16