Toyota CAMRY 2007 User manual

Remote Starter Integration for the 2007 Toyota Camry equipped
with the Smart Key System with Push Button Start
1.0Materialrequired:
-Remote Car Starter
-Xpresskit : XK05-PKT2 or Bypasskit :PKT2
-One 5-wire relay for auto lamp circuit
Key required for programming: 1
Average installation time: 2.5 hours
Difficulty level: Medium
2.0Preparation:
-Remove the driver’s side under dash, as well as the knee airbag bolts. Move the Airbag
aside, but DO NOT DISCONNECT the Airbag connector in order to avoid setting any
vehicle codes.
-Remove the driver’s side floor heating duct, in order to access the vehicle IMI & IMO
wires easily.
3.0Installation:

The remote car starter will be installed in a conventional manner even if the car is
equipped with the Smart Key “Push-to-Start” system.
3.01MainIgnitionHarnessConnection:
Most of the connections will be done behind the Fuse box. This fuse box is located
under the driver side underdash.
Also, the vehicle’s TACH wire can be found inside vehicle, as per diagram below and it
is suggested to use this wire for the remote start tach source. The remote start hood pin
switch wire is the only wire which must be run into the engine compartment for safety.
Accessory (+): White
Ignition 1 (+): Pink
Ignition 2 (+): Light Green
Starter (+): Grey
Tach: Black


3.02WiringlocationfortheBypasskitXK‐05PKT2:
The connection for the XK05-PKT2 will be done on the driver side under dash. The wires
required are from a 5 wires harness coming from behind the heater module, high
above the gas pedal near the firewall. The five wires in this harness are as follows:
Blue: transponder IMI (Immobilizer in) wire, which gets cut in two and wired in series. The
bottom-half wire connects to the kits Violet/White wire and the top-half wire connects
the kits Violet wire.
Green: transponder IMO (Immobilizer out) wire, which gets wired in parallel with the kits
Orange wire.
White/Black, White & Orange…these wire are not used for installation
The GREEN LED output wire from the XK05-PKT2 is not required for this installation. The
vehicle LED does come on during remote start.


3.03Wiringlocationfordoorlocksandfactoryalarmcontrol:
The wires to control the factory alarm and the door locks are located behind the
driver’s kick panel. These wires must receive negative pulses.
It is mandatory to disarm the OEM alarm system before remote start sequence
Grey Unlock Wire: A double pulse unlock (-) output is required to disarm and unlock all
doors. The first unlock (-) pulse disarms OEM alarm and unlocks driver’s door, the second
pulse will unlock all other doors.
In order to disarm the OEM alarm when remote starting, this GREY wire requires a pulse
before start, which unlocks the driver’s door. So, if the remote systems unlock output
does offer a pulse before start, then connect both the unlock and disarm (-) output
wires to the vehicle’s GREY unlock wire.
Brown Lock Wire:In order to lock and arm the OEM alarm system a (-) pulse is required
for the vehicle’s BROWN lock wire. If the vehicle’s ignition on the alarm will not arm, if
locking with remote.
3.04WiringlocationforParkinglightsandAutolampShutdown:

The wires to control the parking lights and the Auto lamp circuit are located at the light
switch on the steering column.
Parking Lights (-): Black
Auto Lamp Circuit (+): GREEN - With the use of a relay, opening the AUTO LAMP circuit
momentarily ensures the vehicle’s head lamps do not stay on after remote start shut-
down sequence. If this is not done the head lamps will remain on for a period of 10-20
minutes and could lead to a battery discharge situation. Please relay configuration
below for proper connection:
Pin 85: Rearm (-)
Pin 86: +12 volt
Pin 30: Green wire connector side
Pin 87a: Green wire Switch side
Pin 87: not used


3.05FinalConnections:
You now have to hook up all of the remaining wires required for the remote start.
-Brake input
-Ground wire
-The antenna

4.00ProgrammingofthePKT2:
1- Connect the module
2- Turn the vehicle to the ignition position
3- The LED flash once
4- Start the vehicle.
5- The module is programmed
(*If the LED stays on, check your connection.)
5.00FinalVerification:
After finishing installation of the remote start system, please verify the following:
-The vehicle’s OEM alarm does not trigger upon remote start system
-All vehicle doors lock after remote start system is running
-All vehicle lights turn off with the shutdown of remote start system
-All doors unlock with the press of the remote unlock button
END‐USEROPERATINGINSTRUCTIONS:
When vehicle is under remote start…
1 - Press remote unlock button
2 - Enter vehicle with the OEM Smart Key
3 - Press Push-to-Start button once (steering wheel will unlock)
4 - Press button one more time (now apply brake, shift vehicle into gear and drive)