Toyotomi TKG-628R32 User manual

User’s Manual
Οδ
Manuale d’installazione ed uso
ηγίες Χρήσης
ΚΛΙΜΑΤΙΣΤΙΚΟ ΤΟΙΧΟΥ ΤΥΠΟΥ INVERTER
W
CONDIZIONATORE SPLIT
ALL MOUNTED AIR CONDITIONER INVERTER TYPE
MODELS/ΜΟΝΤΕΛΑ/MODELLI
TKN/TKG-628R32
TKN/TKG-635R32
TKN/TKG-656R32
TKN/TKG-671R32
Thank you for purchasing our product.
tBefore using this product, be sure to read this Instruction Manual to ensure proper usage. Please
keep this manual for later reference.
tImproper use of this product may result in a malfunction, failure, unexpected accident, or create
a potential hazard.
Ε
Grazie per aver scelto un prodotto TOYOTOMI.
Per un corretto funzionamento, leggere attentamente questo manuale prima di
usare il condizionatore e conservarlo per una futura consultazione.
υχαριστούμε για την επιλογής σας στο κλιματιστικό TOYOTOMI.
Για τη σωστή του χρήση παρακαλούμε διαβάστε το εγχειρίδιο χρήσης προσεκτικά, πριν θέσετε
τη μονάδα σε λειτουργία και κρατήστε το σε καλή κατάσταση για μελλοντική αναφορά.

2GB
R32: 675

3GB
The Refrigerant
WARNING：
To realize the function of the air conditioner unit, a special refrigerant circulates in
the system. The used refrigerant is the fluoride R32, which is specially cleaned.
The refrigerant is flammable and inodorous. Furthermore, it can leads to explosion
under certain conditions. But the flammability of the refrigerant is very low. It can
be ignited only by fire.
Compared to common refrigerants, R32 is a nonpolluting refrigerant with no harm
to the ozonosphere. The influence upon the greenhouse effect is also lower. R32
has got very good thermodynamic features which lead to a really high energy
efficiency. The units therefore need a less filling.
DO NOT use means to accelerate the defrosting process or to clean, other than those
recommended by the manufacture. Should repair be necessary, contact your nea-
rest authorized Service Center. Any repairs carried out by unqualified personnel
may be dangerous. The appliance shall be stored in a room without continuously
operating ignition sources. (for example: open flames, an operating gas appliance
or an operating electric heater.) DO NOT pierce or burn.
Appliance shall be installed, operated and stored in a room with a floor area larger
than 4m .
Appliance filled with flammable gas R32. For repairs, strictly follow manufacturer’s
instructions only. Be aware that refrigrants not contain odour. Read specialist’s
manual.
2
Appliance filled with flammable gas R32.
Before use the appliance, read the owner’s manual first.
Before repair the appliance, read the service manual first.
Before install the appliance, read the installation manual first.

4GB
Precautions
DO NOT connect air conditioner to multi-purpose socket.
This appliance can be used by children aged from 8
Operation and Maintenance
If the supply cord is damaged, it must be replaced by
the manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
DO NOT spray wateronindoorunit. It may cause electric
shock or malfunction.
Otherwise, it may cause fire hazard.
Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by
children without supervision.
years and above and persons with reduced physical,
sensory ormental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe
way and understand the hazards involved.
DO NOT wash the air conditioner with water to avoid
electric shock.
After removing the filter, do not touch fins to avoid injury.
DO NOT use fire or hair dryer to dry the filter to avoid
deformation or fire hazard.
Disconnect power supply when cleaning air
conditioner. Otherwise, it may cause electric shock.
WARNING

5GB
DO NOT block air outlet or air inlet. It may cause
malfunction.
remote controller may be broken.
Power cord is overheating or damaged.
There is abnormal sound during operation.
Circuit break trips off frequently.
Air conditioner gives off burning smell.
There is a leakage from the indoor unit.
contact the dealer or qualified professionals for service.
When turning on or turning off the unit by emergency
operation switch, please press this switch with an insulating
object other than metal.
outlet. It may cause personal injury or damage.
Precautions
conditioner and disconnect power immediately, and then
If the air conditioner operates under abnormal conditions,
it may cause malfunction, electric shock or fire hazard.
DO NOT spill water on the remote controller, otherwise the
electric shock or damage. Please contact your dealer
when you need to repair air conditioner.
DO NOT repair air conditioner by yourself. It may cause
objects. It may cause damage or personal injury.
DO NOT step on top panel of outdoor unit, or put heavy
When below phenomenon occurs, please turn off air
DO NOT insert fingers or objects into air inlet or air
Maintenance must be performed by qualified
professionals. Otherwise, it may cause personal injury
or damage.
WARNING

6GB
Install the circuit break. If not, it may cause malfunction.
of at least 3 mm in all poles should be connected in fixed
wiring.
magnet buckle and heating buckle function, it can protect
the circuit-short and overload.
power supply circuit and circuit break.
Precautions
note the following table. Air switch should be included
Make sure the power supply matches with the
requirement of air conditioner. Unstable power supply or
incorrect wiring may result in electric shock, fire hazard or
malfunction. Please install proper power
supply cables before
using the air conditioner.
An all-pole disconnection switch having a contact separation
Must follow the electric safety regulations when installing
the unit.
grounding wire of power socket.
Properly connect the live wire, neutral wire and
Including an circuit break with suitable capacity, please
Air conditioner should be properly grounded. Incorrect
DO NOT use unqualified power cord.
grounding may cause electric shock.
According to the local safety regulations, use qualified
Installation must be performed by qualified professionals.
Otherwise, it may cause personal injury or damage.
Attachment
WARNING

7GB
Installation must be performed in accordance with the
persons in order to avoid a hazard.
must be properly grounding with specialized grounding
device by a professional. Please make sure it is always
grounded effectively, otherwise it may cause electric shock.
The appliance must be positioned so that the plug is
accessible.
All wires of indoor unit and outdoor unit should be
connected by a professional.
national wiring regulations.
requirement of NEC and CEC by authorized personnel
only
Precautions
wire, which cannot be used for other purposes.
The grounding resistance should comply with national
electric safety regulations.
The air conditioner is the first class electric appliance. It
keep the interconnection cable away from the copper
tube.
The temperature of refrigerant circuit will be high, please
the manufacturer, its service agent or similarly qualified
If the supply cord is damaged, it must be replaced by
The yellow-green wire in air conditioner is grounding
The appliance shall be installed in accordance with
DO NOT put through the power before finishing installation.
WARNING
any work related to electricity and safety.
Be sure to cut off the power supply before proceeding

8GB
Instructions for installation and use of this product are
provided by the manufacturer.
Precautions
WARNING
The indoor unit should be installed close to the wall.
reachable after finishing installation.
far away from animals or plants. If it is unavoidable,
please add the fence for safety purpose.
If you need to relocate the air conditioner to another
place, only the qualified person can perform the work.
Otherwise, it may cause personal injury or damage.
must be installed in the line.
For the air conditioner without plug, an circuit break
Select a location which is out of reach for children and
For the air conditioner with plug, the plug should be
If the length of power connection wire is insufficient,
please contact the supplier for a new one. Avoid
extending the wire by yourself.

9GB
Precautions
WARNING
Leak test is a must after installation.
It is not allowed to drill hole or burn the connection pipe.
The air conditioner must be installed in a room that is
larger than the minimum room area. The minimum room
area is shown on the nameplate or table a in page 39.
The air conditioner is not allowed to use in a room that
has running fire (such as fire source, working coal gas
ware, operating heater).
Instructions for installation and use of this product are
provided by the manufacturer.
Working temperature range
NOTICE:
Indoor side DB/WB ( ) Outdoor side DB/WB ( )
62/3432/23gniloocmumixaM
81/42-/72gnitaehmumixaM
5151- ~ 43 ; for heat pump unit is - ~ 43 .

10 GB
air inlet
Connection wire
air outlet
MODE FAN
TURBO
SLEEP
TIMER ON
CLOCK
WIFI LIGHTTEMP
QUIET
TIMER OFF
I SENSE

11 GB
Buttons on remote controller
Introduction for icons on display screen
1ON/OFF button
2MODE button
3FAN button
4TURBO button
6button
7button
9I SENSE button
14 LIGHT button
15 button
16 TEMPbutton
11 CLOCK button
12 QUIE T button
13 WIFI button
10 TIMER ON / TIMER OFF button
8SLEEPbutton
5ŸEXWWRQ
Ÿ
Send signal
Turbo mode
8삸heating function
Set temperature
Set time
X-FAN function
TIMER ON /TIMER OFF
Child lock
Up & down swing
Left & right swing
Set fan speed
Light
Temp. display type
:Set temp.
:Outdoor ambient temp.
:Indoor ambient temp.
Sleepmode
Clock
Heat mode
Fan mod e
Dry mode
Coolmode
Auto mode
Operation mode
ISENSE
Healthy mode
Scavenging functions
Quiet
MODE FAN
TURBO
SLEEP
TIMER ON
CLOCK
WIFI LIGHTTEMP
QUIET
TIMER OFF
I SENSE
E
MOD
MODEMODE
MODE
ODE
ODE
DE
E
MO
F
F
F
F
ANAN
AN
N
F
F
F
F
TUR
TURBO
TURBO
TURBO
TURBO
TURBO
TURBO
T
SLEEP
P
P
P
SLE
SLEEP
SLEEP
EP
P
P
TIM
TIM
MER
ER
ER
M
ON
ON
CLOCK
CK
CLOCK
K
K
CLOCK
CLOCKCLOCK
CLOCK
K
K
CLOCK
K
CLOCK
K
WIFI
F
F
WIFI
W
WIFI
WIFI
WI
FI
LIGHT
LIGHT
IGHT
H
LIG
GH
LI
IG
LIGHT
IGHT
TEMP
TEMP
TEM
M
MP
TEMP
QUIET
UIET
I
UI
QUI
QU
U
QUIE
QUIET
Q
Q
Q
T
TIME
IMER
MER
OF
FF
I SEN
I SEN
N
I
I SEN
SEN
I SEN
SE
E
S
S
SE
SE
MODE FAN
TURBO
SLEEP
TIMER ON
CLOCK
WIFI LIGHTTEMP
QUIET
TIMER OFF
I SENSE
6
3
79
11
13
15
12
14
16
10
8
5
4
2
1

12 GB
F
F
F F
F
Introduction for buttonson remote controller
1
2
T FANRY AT
Note:
with multifunction; For some function, which the model does not have, if press
to ex-factory setting. Set temperature cannot be adjusted and will not be displayed
mode. Dry indicator “ ” on indoor unit is ON. Under dry mode, fan speed cannot
adjust fan blowing angle. (Cooling only unit will not receive heating mode signal.
If setting heat mode with remote controller, press ON/OFF button cannot start up
the unit.)

13 GB
Introduction for buttons on remote controller
FAN button
3
Note:
TURBO butto n
4
Un COOL o HEAT o , t button to tu n to qu k COOL o qu k
HEAT
to
to
,
, , ,
Auto
F
F
Note:
Set temperature range from remote controller: 16 - 30℃(61 - 86°F); Fan speed: auto, low
speed, low-medium speed, medium speed, medium-high speed, high speed.
It is Low fan speed under Dry mode.
X-FAN function: Hold fan speed button for 2 seconds in COOL or DRY mode, the icon
“ ” is displayed and the indoor fan will continue operation for a few minutes in order
to dry the indoor unit even though you have turned off the unit. After energization,
X-FAN OFF is defaulted. X-FAN is not available in AUTO, FAN or HEAT mode.
button indoor fan will continue running for a few minutes at low speed. In this
period, hold fan speed button for 2 seconds to stop indoor fan directly.

14 GB
GB
Note:
Introduction for buttons on remote controller
7
6
(
5
TIMERTIMER
.
(R
Holding “ ” or “ ” button, 2 seconds later, set temperature on remote controller
will change quickly. On releasing button after setting is finished, temperature
indicator on indoor unit will change accordingly. (Temperature cannot be adjusted
under auto mode.)
Press this button can select left and right swing angle. Fan blow angle can be selected
circularly as below:
Press this button continuously more than 2 seconds, the main unit will swing back
and forth from left to right, and then loosen the button, the unit will stop swinging and
present position of guide louver will be kept immediately.
Under swing left and right mode, when the status is switched from off to , if
press this button again 2 seconds later status will switch to off status directly; if
press this button again within 2 seconds, the change of swing status will also depend
on the circulation sequence stated above.
Press this button can select up and down swing angle. Fan blow angle can be selected
circularly as below:
louver will automatically swing up and down at maximum angle.
Hold “ ” button above 2 seconds to set your required swing angle. When reaching
your required angle, release the button.

15 GB
SLEEP button
8
Introduction for buttons on remote controller
Note:
.
f to , if
press this button again 2 seconds later, status will switch to off status directly;
if press this button again within 2 seconds, the change of swing status will also
depend on the circulation sequence stated above.
In the Cooling or Heating mode, press this button to start sleep mode. Once you set it up,
this symbol “ “ appears on the screen remote control. Sleep Mode has three places to
choose from, Sleep Mode 1, Sleep Mode 2, Sleep Mode 3. To navigate through the op-
tions, press the sleep button. By pressing it once Sleep Mode 1 “ “ will be activated, by
pressing it twice Sleep Mode 2 “ “ activates, three times Sleep Mode 3 “ “ activates.
Pressing the button for the fourth time will disable this function and “ “ will disappear.
If you deactivate the air conditioner, sleep mode will be deactivated. During DRY, FAN,
AUTO, Energy Saving & “8℃Heating” functions, sleep mode is not available.
Sleep Mode 1
Sleep Mode 1 “ “ is available in Cooling or Heating mode. By activating this function, the
air conditioner’s temperature increases by one degree per hour in “Cooling” mode and
decreases by one degree per hour in “Heating” mode.
Sleep Mode 2
Sleep mode 2 “ “ will only be activated during Cooling or Heating mode.
During Cooling mode:
-If the air conditioner temperature is set between 16 - 23℃, the temperature will increase
by one degree per hour for the next 3 hours after the power is turned on and then remains
stable. At the 8th hour after the operation is switched on, the temperature will be reduced
by one degree automatically.
-If the air conditioner temperature is set between 24 - 27℃, the temperature will increase
by one degree per hour for the next 2 hours from the start of the operation and then remain
stable. At the 8th hour after the operation is switched on, the temperature will be reduced by
one degree automatically.
Press this button continuously more than 2 seconds, the main unit will swing back
and forth from up to down, and then loosen the button, the unit will stop swinging
and present position of guide louver will be kept immediately.

16 GB
-If the air conditioner temperature is set between 28 - 29℃, the temperature will increase
to a certain degree within the next hour of activation and then remain stable. At the 8th
hour after the operation is switched on, the temperature will be reduced by one degree
automatically.
-If the air conditioner temperature is set from 30℃to above, it will remain constant for 7
hours after the operation is switched on and at 8 o’clock the temperature will be reduced
by one degree automatically.
During Heating mode:
-If the air conditioner selection is 16℃, the air conditioner will continue to operate at
this temperature.
-If the air conditioner temperature is between 17℃and 20℃, the air conditioner’s
temperature will drop to a certain extent after the first hour of the operation and then
remain constant.
-If the air conditioner’s temperature is between 21 - 27℃, the air conditioner’s tempera-
ture will drop by one degree per hour within the rst 2 hours of activation and then remain
constant.
-If the air conditioner’s temperature is between 28 - 30℃, the air conditioner’s tempera-
ture will be reduced by one degree per hour in the first 3 hours after activation and then
will remain constant.
Sleep Mode 3
Sleep Mode 3 “ “ is available in Cooling or Heating modes. By activating this function,
you can create your own personalized program based on time and temperature. To set
the time and temperature, press the “TURBO” button for 3 seconds, and the temperature
icon will ash on the remote-control screen.
You can set the temperature by hour, up to 8 hours continuously. With the “ ” and “ ”
buttons you can adjust and change the temperature. To con rm the desired temperature,
press the “TURBO” button. To set the temperature for the second hour repeat the same
procedure.
The personalized program is stored in the memory despite the deactivation of the air
conditioner.
++++++++++

17 GB
Introduction for buttons on remote controller
I SENSE button
9
Press this button to start I SENSE function and " " will be displayed on the remote
controller. After this function is set, the remote controller will send the detected
ambient temperature to the controller and the unit will automatically adjust the
indoor temperature according to the detected temperature. Press this button again
to close I SENSE function and " " will disappear.
the remote controller near the object of high temperature or low temperature in
order to avoid detecting inaccurate ambient temperature.
TIMER ON button
"TIMER ON" button can set the time for timer on. After pressing this button, " "
icon disappears and the word "ON" on re
" "button to adjust TIMER ON setting.
TIMER ON setting will increase or decrease 1 minute. Hold “ ” or “ ” button,
2 seconds later, the time will change quickly until reaching your required time.
resumes displaying. Cancel TIMER ON: Under the condition that TIMER ON is
started up, press "TIMER ON" button to cancel it.
TIMER OFF button
"TIMER OFF" button can set the time for timer off. After pressing this button, " "
" " button to adjust TIMER OFF setting.
Press "TIMER OFF" word "OFF" will stop blinking. " " icon resumes displaying.
Cancel TIMER OFF. Under the condition that TIMER OFF is started up, press
"TIMER OFF" button to cancel it.
TIMER ON / TIMER OFF button
10
When I SENSE function is turned on, the remote controller should be put within the
area where indoor unit can receive the signal sent by the remote controller.
TIMER OFF setting will increase or decrease 1 minute. Hold “ ” or “ ” button,
2 seconds later, the time will change quickly until reaching your required time.

18 GB
QUIET button
Wi-Fi button
12
13
Press this button, the Quiet status is under the Auto Quiet mode (display " " and
"AUTO" signal ) and Quiet mode (display " " singal) and Quiet OFF (there is no
signal of " " displayed), after powered on, the Quiet OFF is defaulted.
Note:
The Quiet function cannot be set up in Fan and Dry mode; Under the Quiet mode,
the fan speed is not available.
Introduction for buttons on remote controller
Press this button to set clock time. " " icon on remote controller will blink. Press
“ ” or “ ” button within 5 seconds to set clock time. Each pressing of “ ” or “ ”
button clock time will increase or decrease 1 minute. If hold “ ” or “ ” button, 2
seconds later, time will change quickly. Release this button when reaching your
required time. Press “CLOCK” button to confirm the time. “ ” icon stops blinking.
Note:
The interval between two operation cannot exceeds 5 seconds. Otherwise, remote
controller will quit setting status. Operation for TIMER ON/TIMER OFF is the same.
LO K button
11
Note:
ff status, you can set TIMER OFF or TIMER ON simultaneously.
TIMER ON or TIMER OFF, please adjust the clock time.
After starting up TIMER ON or TIMER OFF, set the constant circulating valid.
After that, air conditioner will be turned on or turned off according to setting time.
ON/OFF button has no effect on setting. If you do not need this function, please
use remote controller to cancel it.
when indoor ambient temperature ≧ 28℃, indoor fan will operate at notch 2 speed
or quiet mode according to the comparison between indoor ambinet temperature
and set temperature.
Under heating mode: indoor fan operates at notch 3 speed or quiet mode accord-
ing to the comparison between indoor ambient temperature and set temperature.
Under dry, fan mode: indoor fan operates at quiet mode.
Under auto mode: the indoor fan operates at the auto quiet mode according to
actual cooling, heating or fan mode.
Press " WiFi " button to turn on or turn off WiFi function. When WiFi function is
turned on, the " WiFi " icon will be displayed on remote controller; Under status
of remote controller off, press "MODE" and " WiFi " buttons simultaneously for
1 second, WiFi module will restore to factory default setting.

19 GB
LIGHT button
14
Press this button to turn off display light on indoor unit. " " icon on remote
controller disappears. Press this button again to turn on display light. " " icon is
displayed.
Introduction for buttons on remote controller
15
Press this button to achieve the on and off of healthy and scavenging functions in
LCD displays " "(not available). Press the button for t
scavenging functions simultaneously; LCD displays " " and " " .
Press this button for the third time to quit healthy and scavenging functions
simultaneously.
Press the button for the fourth t ime to start healthy function; LCD display " " .
Press this button again to repeat the operation above.
button
16 TEMP button
By pressing this button, you can see indoor set temperature, indoor ambient temp-
erature or outdoor ambient temperature on indoor unit’s display. The setting on
remote controlleris selected circularly as below:
no display
r, temperature indicator
on indoor unit displays set temperature.
r, temperature indicator on indoor unit
displays indoor ambient temperature.
r, temperature indicator on indoor unit
displays outdoor ambient temperature (not available).
Note:
Outdoor temperature display is not available for some models. At that time, indoor
unit receives " " signal, while it displays indoor set temperature.
’s defaulted to display set temperature when turning on the unit. There is no
display in the remote controller.
y.
outdoor ambient temperature, indoor
temperature indicator displays corresponding temperature and automatically turn
he second time to start
healthy and

20 GB
GB
Function introduction for combination buttons
Energy-saving function
Under cooling mode, press "TEMP" and " CLOCK" buttons simultaneously to
start up or turn off energy-saving function. When energy-saving function is started
up, "SE" will be shown on remote controller, and air conditioner will adjust the set
temperature automatically according to ex-factory setting to reach to the best
energy-saving effect. Press "TEMP" and "CLOCK"buttons simultaneously again to
exit energy-saving function.
Note:
ed is defaulted at auto speed and it cannot
be adjusted.
Under energy-saving function, set temperature cannot be adjusted. Press "TURBO"
button and the remote controller will not send signal.
ion cannot operate at the same time. If
energy-saving function has been set under cooling mode, press sleep button will
cancel energy-saving function. If sleep function has been set under cooling
mode, start up the energy-saving function will cancel sleep function.
8 heating function
Under heating mode, press "TEMP" and "CLOCK" buttons simultaneously to start
up or turn off 8 heating function. When this function is started up, " " and "8 "
will be shown on remote controller, and the air conditioner keep the heating status
at 8 . Press "TEMP" and "CLOCK" buttons simultaneously again to exit 8
heating function.
Note:
heating function, fan speed is defaulted at auto speed and it cannot be
adjusted.
heating function, set temperature cannot be adjusted. Press “TURBO”
button and the remote controller will not send signal.
heating function cannot operate at the same time. If 8℃
heating function has been set under cooling mode, press sleep button will cancel
8 heating function. If sleep function has been set under cooling mode, start up
the 8 heating function will cancel sleep function.
temperature display, the remote controller will display 46 heating.
Child lock function
ff child lock function. When
child lock function is on, " " icon is displayed on remote controller. If you operate
the remote controller, the " " icon will blink three times without sending signal to
the unit.
Temperature display switchover function
Under OFF status, press " " and "MODE" buttons simultaneously to switch temp-
erature display between and .