Toyotomi FS1060A User manual

Service Manual
MODEL:
FS1060A

1Introduction and Features
Model Remarks
FS 1060A

2
COOLING HEATING
16000W 18000W
6400W 6200(9700)W
7800W 7800(11300)W
12.05A 12.05(17.25) A
Model of Indoor Unit
Fan Motor Speed (r/min) (H/M/L)
Output of Fan Motor (w)
Input of Heater (w)
Fan Motor Capacitor (uF)
Fa n Mo to r R L A(A)
Fan Type-Piece
Diameter-Length (mm)
Evaporator
Pipe Diameter (mm)
Row-Fin Gap(mm)
Coil length (l) x height (H) x coil width (L)
Swing Motor Model
Output of Swing Motor (W)
Fus e (A)
Sound Pressure Level dB (A) (H/M/L)
Sound Power Level dB (A) (H/M/L)***
Dimension (H/W/D) ( mm)
Dimension of Package (L/W/H) ( mm)
Net Weight /Gross Weight (kg)
2000/720/515
60/85
ĭ7
3-1.4
914.4X471X42.2
SM016
/
540/1750/380
4W
PCB 5.0A
550/500/450 r/min
130W
3500W
6uf
5.2
2.5
/
FS 1060Ai
FS 1060A
380-415V 3N
50Hz
2000
Mode l
Function
Rated Voltage
Rated Frequency
Indoor unit
Energy Class
Total Capacity (Btu/h)
Power Input (W)
Rated Input (W)
Rated Current (A)
Air Flow Volume (m3/h) (H/M/L)**
Dehumidifying Volume (l/h)
EER / C.O.P (W/W)
58/53/50
1.59A
Centrifugal fan – 1
ij369X 180.5
Aluminum fin-copper tube
Specification and Technical Parameter

FS 1060Ao
Dallian SANYO / SANYO
C-SBN453H8D
SCrOll
67A
9.77A
5750W
UP18
Capillary
Capacitor
-7ćİTİ45ć
Aluminum fin-copper tube
ĭ9.52
3-1.8
745X1219.2X66
940 rpm
92W
0.42
4uf
5000 m3/h
Axial fan -1
ĭ450X156
Auto defrost
T1
I
IP24
3.9
2.21
61
/
950X1250X412
450X1110X1280
115/126
R410A/5.0Kg
5M
100g//m
Liquid Pipe (mm) ĭ12(1/2")
Gas Pipe (mm) ĭ19(3/4")
Height (m) 30
Length (m) 30
Length (m)
Gas additional charge(g/m)
Sound Power Level dB (A) (H/M/L)
Dimension (W/H/D) ( mm)
Dimension of Package (L/W/H)( mm)
Net Weight /Gross Weight (kg)
Moisture Protection
Permissible Excessive Operating
Pressure for the Discharge Side(MPa)
Permissible Excessive Operating
Pressure for the Suction Side(MPa)
Sound Pressure Level dB (A) (H/M/L)
Fan Diameter (mm)
Defrosting Method
Climate Type
Isolation
Fan Mo to r R L A(A)
Fan Motor Capacitor (uF)
Air Flow Volume of Outdoor Unit
Fan Type-Piece
Rows-Fin Gap(mm)
Coil length (l) x height (H) x coil width (L)
Fan Motor Speed (rpm)
Output of Fan Motor (W)
Starting Method
Working Temp Range (ć)
Condenser
Pipe Diameter (mm)
Compressor RLA(A)
Compressor Power Input(W)
Overload Protector
Throttling Method
Outdoor
unit
Outer Diameter
Max Di s tance
Connec
tion
Pipe
Refrigerant Charge (kg)
Model of Outdoor Unit
Compressor Manufacturer/trademark
Compressor Model
Compressor Type
L.R.A. (A)
If the above specification's parameter has been changed, please refer to the nameplate.

3Parts' Name
air outlet
display screen
panel
air intake panel
air intake
air discharge
remote controller
timer
swing
fan speed mode ON/OFF
temperature
air intake
display screen
drain pipe
air discharge
connecting pipe
sealing tape

4Outline and Installation Dimension
Indoor unit's outline and installation size
unit:
rear
front
Pipe side should be at least 30cm. Pipe side should be at least 30cm.

Outdoor unit's outline and installation size
unit:
more than
more than 600
more than 600
more than 600
bolt
nut

5
If above electric circuit diagram has been changed, please refer to it on the body.

66
66
6Controller's function manual and operation method
1Temperature Parameters
 Indoor preset temperature (Tpreset)
 Indoor ambient temperature (Tamb.)
2Basic Functions
Once the unit is started under any modes, the compressor will keep running within 6 minutes. Once the unit's
stopped, it cannot be restarted until after 3-minute lag.
(1) Cooling Mode
Cooling Conditions and Process
When Tamb.Tpreset+1 , the unit will run under cooling mode, in which case the compressor and outdoor fan willć
EHstarted, and the indoor fan will run at preset speed.
When T ambTpreset -1 , the unit will be stopped under cooling mode,ćin which case the compressor and outdoor fan will
be stopped, while the indoor fan will run at preset speed.
When Tpreset -1 <Tćamb.<T
preset +1 , the unit will maintain its original operating status.ć
¾ Under cooling mode, the temperature can be set within a range from 16 to 30 . The initial value is 25 .ćć
The outdoor fan runs at high speed.
Dry Mode
Drying Conditions and Process
When T amb.Tpreset +2 , the unit will run under cooling mode, in which case the compressor and outdoor fan willć
ｂｅ started, and the indoor fan will run at low speed.
When Tpreset -2 Tćamb.Tpreset +2 , the compressor, indoor fan and outdoor fan will run 6 minutes and stop 4 minutes
ć
ｉｎ repeated cycle, while the indoor fan will run at low speed.
When T amb.< Tpreset -2 , the cćompressor, outdoor fan and indoor fan will be stopped.
¾ Under this mode, the temperature can be set within a range from 16 to 30 . The initial value is 25 .ćć
The outdoor fan runs at high speed.
Heating Mode
Heating Conditions and Process
When Tamb. Tpreset- 1 , the unit is running in heating mode. Meawhile, the reversing valve, compressor and the
outdoor fan start running. When the unit is turned on to turn to heating mode or switch to heating mode from other
modes, the four-way valve start running after the compressor is started for the first time in 20s, and the indoor fan will
start running after 90s delayed at most.
start cooling
original running status
stop cooling
hign speed
hign speed
stop
run
set fan speed
compressor
outdoor fan
indoor fan
mins
mins mins
Tpreset
Tpreset Tamb.
compressor
outdoor fan
indoor fan
stop
run
cooling
drying
stop running
low speed low speed low speed
high speed high speed high speed
mins mins
mins m
ins
Tpreset
Tpreset
Tamb.

¾

If T amb.Tpreset +1 , the compressor and outdoor fan will be stopped, while reversalćvalve will remain energized and the
indoor fan will run at low speed for 10s and then it will stop running.
When Tpreset -1 <Tćamb.< Tpreset +1 , the unit will maintain its original operating status.ć
Under heating mode, the temperature can be set within a range from 16 to 30 . The initial value is 25 .ćć
If the unit is switched off under heating mode or switched from heating mode to another mode, the 4-way valve will
be de-energized after 2-minute lag.
Defrosting Conditions and Process
When detecting any frost in condenser, the system will start defrosting( The auxiliary electric heater,if any, will be stopped firstly, and then
start defrosting after 1 min. ),in which case the compressor, indoor fan and outdoor fan will be stopped simultaneously, the 4-way valve
will stop in 3S and the compressor will be started in another 30S.(Defrost will not be detected during high temperature protection).When
detecting the frost in condenser is removed, the defrost is completed, in which case the compressor stops, while the 4-way valve runs.
30S later, the compressor starts running,outdoor fan runs,and the indoor fan will run in 90S at least.
Fan Mode
Indoor fan will run at preset speed Auto Speed Low Speed Mid. Speed High Speed
¾The temperature can be set within a range from 16 to 30 . The initial value is 25ć
AUTO Mode
Under this mode, the system will automatically select its running mode (cooling, dry, heating or fan) with the change
of ambient temperature.
Once a mode is started, the unit will run at least 30 seconds before it can turn to other running status under
auto mode according to the ambient temperature.
Other Control
Sleep Function
If the controller is under cooling or dry mode, the preset temperature will be increased by 1 one hourć
after running under sleep mode and will be increased by another 1 after two hours. The temperature will increasedć
by 2 within two hours. After that, the unit will run at this temperature.ć
When indoor fan is runnng and Tevap. is lower than Tamb. and Tamb. Tpreset-2 , auxiliary electric heater will start running.
When indoor fan isn't running, or Tevap. is high, or Tamb. is high, the auxiliary electric heater will stop running. After the auxiliary
electric heater is stopped, it can be restarted only after 2min delayed.
outdoor
outdoor
outdoor fan is running at low fan speed;
outdoor fan is running at high fan speed;
outdoor Outdoor fan keep the original running status.
Auxiliary electric heater working condition
stop heating
original running status
start heating
stop
run
compressor
outdoor fan
indoor fan
o
low speed low speed
mins mins mins
Tpreset
Tpreset
setting temperature Tpreset
Tpreset
Tpreset
Tpreset
1hr 2hrs more than 2 hrs