TP-Link omada EAP110-Outdoor User manual

Installation Guide
EAP110-Outdoor
300Mbps Wireless N Outdoor Access Point

Contents
Overview
Typical Network Topology
Lightning and ESD Protection
Hardware Installation
Mount EAP
Connect Cables
Power On
Software Configuration
1
4
5
6
8
9
11
6

Overview
Package Contents
1
Power Cord
D3×28 Plastic Wall
Anchors(Qty.4)
ST3×20 Self-tapping
Screws (Qty.4)
Antennas (Qty.2)
Pole Mounting Strap
Installation Guide
Passive PoE Adapter
Waterproof Rubber
Insert
Mounting Bracket
(for EAP)
Mounting Bracket
(for PoE Adapter)
EAP
Installation Guide
EAP110-Outdoor
300MbpsWireless N Outdoor Access Point

The Panel of EAP
Panel Layout
RESETShielded Ethernet
Port LAN
2

SYS LED Explanation
LED Status Indication
Passive PoE Adapter
3
Solid green The device is initializing or working properly .
Flashes red System errors. RAM, Flash, Ethernet, WLAN or
rmware may be malfunctioning.
Flashes yellow Firmware update is in progress. Do not disconnect
or power o the device.
Double ashes red,
green, yellow
The device is being reset to its factory default
settings.
Flashes green twice Initialization is completed.
Power LED:
On: Power on
Off: Power off
Remote Reset:
Press and hold for 8 seconds
to reset the EAP to its factory
default settings.

4
A DHCP server (typically a router) with DHCP function enabled is required to
assign IP addresses to the EAPs and clients in your local network.
EAP EAP EAPPC
Switch
Router
Internet
Clients
Typical Network Topology
EAP Controller

5
Lightning and ESD Protection
Before mounting EAP, you should consider Lightning and ESD
Protection to ensure safety.
Proper grounding is extremely important for outdoor devices. By
using a shielded CAT5e (or above) cable for connection, you can
reduce the damage of ESD attacks.
EAP
Grounded 3-wire
Power Outlet
Grounded PoE Adapter
Shielded CAT5e (or above)
Cable

6
Hardware Installation
Mount EAP
Option 1: Pole Mounting
Lead the end of the pole mounting
strap through the back of the EAP.
Step 1:
Position the EAP and wrap the pole
mounting strap around the pole.
Feed the end through the
screw-block and tighten the strap
until the EAP is secure.
Step 2:
Connect the antennas to the EAP.
Step 3:
The EAP can be pole-mounted or wall-mounted when working
independently.

7
Step 4:
Connect the antennas to the EAP.
Step 1:
Place the mounting bracket (for
EAP) in the right position. Mark two
positions for the screw holes .
Drill two 6mm holes for the screws
at the marked positions.
Step 2:
Insert the plastic wall anchors into
the 6mm holes. Align the bracket
(for EAP) to the plastic wall anchors
and drive the self-tapping screws
into the anchors through the
bracket (for EAP).
Step 3:
Align the mounting tabs on the
back of the EAP with the slot of
the mounting bracket (for EAP).
Push and slide the EAP downward
until it locks into place.
Option 2: Wall Mounting

8
Connect Cables
Firmly grasp the rear of the interface
cover and pull it downward.
Step 1:
Use an adequate Ethernet cable to
connect the LAN port. The length of
cable is up to 100m for steady
power supply. Shielded CAT5e (or
above) cable is recommended.
Step 2:
Attach the waterproof rubber insert
to the groove at the underside of
the device for waterproofing and
replace the cover until it firmly locks
into place.
Step 3: