TP-Link TL-WA7110ND User manual

TL-WA7110ND
150Mbps High Power Wireless Access Point
REV1.0.0
1910011047

COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark
of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are
trademarks or registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from
TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD.
All rights reserved.
http://www.tp-link.com

FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1）This device may not cause harmful interference.
2）This device must accept any interference received, including interference that may
cause undesired operation.
Any changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications could void the
user’s authority
to operate the equipment.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This device and its antenna must not be co-located or operating in
conjunction with any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is
applicable to only Mobile Configurations. The antennas used for this transmitter
must be installed to provide a separation distance of at least 20 cm from all persons and
must not be co-located or operating in conjunction with any other antenna or transmitter.”
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.

Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause
undesired operation of the device.
Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie
Canada. Le fonctionnement est soumis aux deux conditions suivantes:
(1)cet appareil ne doit pas provoquer d’interférences et
(2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un
fonctionnement non souhaité de l’appareil.
This device has been designed to operate with the antennas listed below, and having a maximum
gain of 5 dBi. Antennas not included in this list or having a gain greater than 5 dBi are strictly
prohibited for use with this device. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for
successful communication.
Industry Canada Statement
Complies with the Canadian ICES-003 Class B specifications.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with RSS 210 of Industry Canada. This Class B device
meets all the requirements of the Canadian interference-causing equipment regulations.
Cet appareil numérique de la Classe B respecte toutes les exigences du
Règlement sur le matériel brouilleur du Canada.
Korea Warning Statements
당해 무선설비는 운용중 전파혼신 가능성이 있음.
NCC Notice & BSMI Notice
注意！
依據 低功率電波輻射性電機管理辦法
第十二條
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大
功率或變更原設計之特性或功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立
即停用， 並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功
率射頻電 機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。 減少電磁波影
響，請妥適使用。

安全諮詢及注意事項
●請使用原裝電源供應器或只能按照本
產
品注明的電源類型使用本
產
品。
●
清
潔本
產
品之前請先拔掉電源線。請勿使用液體、噴霧
清
潔劑或濕布進行
清
潔。
●注意防潮，請勿將水或其他液體潑灑到本
產
品上。
●
插
槽與開口供通風使用，以確保本
產
品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
●請勿將本
產
品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
●請不要私自打開機殼，不要嘗試自行維修本
產
品，請由授權的專業人士進行此項工作。
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information
When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
This product can be used in the following countries:
AT
BG
BY
CA
CZ
DE
DK
EE
ES
FI
FR
GB
GR
HU
IE
IT
LT
LV
MT
NL
NO
PL
PT
RO
RU
SE
SK
TR
UA
US

TP-LINK TECHNOLOGIES CO., LTD
DECLAR A TION OF CONFORMITY
For the following equipment:
Product Description: 150Mbps High Power Wireless Access Point
Model No.: TL-WA7110ND
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all
the technical regulations applicable to the product within the scope of Council Directives:
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,
Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents
EN 300 328 V1.7.1: 2006
EN 301 489-1 V1.9.2:2011& EN 301 489-17 V2.2.1:2012
EN 55022:2010+AC:2011
EN 55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
EN 60950-1:2006+A11：2009+A1:2010+A12:2011
EN 62311:2008
The product carries the CE Mark:
Person responsible for marking this declaration:
Yang Hongliang
Product Manager of International Business
Date of issue: 2014
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan
Rd, Nanshan, Shenzhen, China

CONTENTS
Package Contents ................................................................................................................................. 1
Chapter 1. Introduction ....................................................................................................................2
1.1 Overview of the Product...........................................................................................................2
1.2 Features ................................................................................................................................... 2
1.3 Conventions ............................................................................................................................. 4
1.4 Panel Layout ............................................................................................................................ 4
1.4.1 The Front Panel................................................................................................................ 4
1.4.2 The Rear Panel ................................................................................................................ 5
Chapter 2. Connecting the Device................................................................................................... 6
2.1 System Requirements.............................................................................................................. 6
2.2 Installation Environment Requirements ................................................................................... 6
2.3 Connecting the Device............................................................................................................. 6
2.3.1 AP Client Router............................................................................................................... 6
2.3.2 AP Router.........................................................................................................................7
2.3.3 Access Point.....................................................................................................................7
2.3.4 Multi-SSID ........................................................................................................................8
2.3.5 Repeater and Universal Repeater.................................................................................... 8
2.3.6 Bridge with AP..................................................................................................................8
2.3.7 Client ................................................................................................................................ 9
Chapter 3. Quick Installation Guide .............................................................................................. 10
3.1 Configure the Device .............................................................................................................10
3.2 Quick Setup ...........................................................................................................................11
3.2.1 AP Client Router............................................................................................................. 14
3.2.2 AP Router.......................................................................................................................18
3.2.3 Access Point...................................................................................................................22
3.2.4 Multi-SSID ......................................................................................................................25
3.2.5 Repeater (Range Extender) ........................................................................................... 28
3.2.6 Bridge with AP................................................................................................................ 31
3.2.7 Client ..............................................................................................................................35
Chapter 4. AP & Multi-SSID & Repeater (Range Extender) & Bridge with AP
& Client
Operation Mode................................................................................................................................... 39
4.1 Login ...................................................................................................................................... 39
4.2 Status ..................................................................................................................................... 39
4.3 Quick Setup ...........................................................................................................................40
4.4 Operation Mode ..................................................................................................................... 40
4.5 WPS ....................................................................................................................................... 41

4.6 Network ..................................................................................................................................42
4.6.1 LAN.................................................................................................................................42
4.7 Wireless .................................................................................................................................43
4.7.1 Wireless Settings............................................................................................................ 44
4.7.2 Wireless Security............................................................................................................ 45
4.7.3 Wireless MAC Filtering...................................................................................................48
4.7.4 Wireless Advanced......................................................................................................... 50
4.7.5 Distance Setting ............................................................................................................. 51
4.7.6 Throughput Monitor ........................................................................................................ 52
4.7.7 Wireless Statistics ..........................................................................................................53
4.8 DHCP .....................................................................................................................................53
4.8.1 DHCP Settings ............................................................................................................... 53
4.8.2 DHCP Clients List........................................................................................................... 54
4.8.3 Address Reservation ...................................................................................................... 55
4.9 System Tools ......................................................................................................................... 56
4.9.1 SNMP .............................................................................................................................57
4.9.2 Time Settings ................................................................................................................. 58
4.9.3 Diagnostic.......................................................................................................................59
4.9.4 Ping Watch Dog ............................................................................................................. 61
4.9.5 Speed Test .....................................................................................................................61
4.9.6 Firmware Upgrade.......................................................................................................... 62
4.9.7 Factory Defaults ............................................................................................................. 63
4.9.8 Backup & Restore .......................................................................................................... 63
4.9.9 Reboot............................................................................................................................64
4.9.10 Password........................................................................................................................64
4.9.11 System log......................................................................................................................65
4.9.12 Statistics .........................................................................................................................66
Chapter 5. AP Client Router & AP Router Operation Mode........................................................68
5.1 Login ...................................................................................................................................... 68
5.2 Status ..................................................................................................................................... 68
5.3 Quick Setup ...........................................................................................................................70
5.4 Operation Mode ..................................................................................................................... 70
5.5 WPS ....................................................................................................................................... 71
5.6 Network ..................................................................................................................................72
5.6.1 WAN ...............................................................................................................................72
5.6.2 MAC Clone ..................................................................................................................... 80
5.6.3 LAN.................................................................................................................................81
5.7 Wireless .................................................................................................................................81
II

5.7.1 Wireless Settings............................................................................................................ 82
5.7.2 Wireless Security............................................................................................................ 86
5.7.3 MAC Filtering..................................................................................................................88
5.7.4 Wireless Advanced......................................................................................................... 90
5.7.5 Distance Setting ............................................................................................................. 91
5.7.6 Throughput Monitor ........................................................................................................ 92
5.7.7 Wireless Statistics ..........................................................................................................93
5.8 DHCP .....................................................................................................................................93
5.8.1 DHCP Settings ............................................................................................................... 93
5.8.2 DHCP Clients List........................................................................................................... 94
5.8.3 Address Reservation ...................................................................................................... 95
5.9 Forwarding .............................................................................................................................96
5.9.1 Virtual Servers................................................................................................................ 97
5.9.2 Port Triggering................................................................................................................ 98
5.9.3 DMZ..............................................................................................................................100
5.9.4 UPnP ............................................................................................................................100
5.10 Security ................................................................................................................................101
5.10.1 Basic Security............................................................................................................... 101
5.10.2 Advanced Security ....................................................................................................... 103
5.10.3 Local Management.......................................................................................................104
5.10.4 Remote Management................................................................................................... 105
5.11 Parental Control ...................................................................................................................105
5.12 Access Control.....................................................................................................................107
5.12.1 Rule ..............................................................................................................................107
5.12.2 Host ..............................................................................................................................109
5.12.3 Target ...........................................................................................................................110
5.12.4 Schedule ......................................................................................................................111
5.13 Advanced Routing................................................................................................................112
5.13.1 Static Routing List ........................................................................................................112
5.13.2 System Routing Table .................................................................................................. 113
5.14 Bandwidth Control................................................................................................................114
5.14.1 Control Settings............................................................................................................114
5.14.2 Rules List......................................................................................................................114
5.15 IP & MAC Binding ................................................................................................................115
5.15.1 Binding Setting ............................................................................................................. 115
5.15.2 ARP List........................................................................................................................116
5.16 Dynamic DNS ......................................................................................................................117
5.17 System Tools .......................................................................................................................120
III

5.17.1 Time Settings ............................................................................................................... 121
5.17.2 Diagnostic.....................................................................................................................122
5.17.3 Firmware Upgrade........................................................................................................123
5.17.4 Factory Defaults ...........................................................................................................124
5.17.5 Backup & Restore ........................................................................................................124
5.17.6 Reboot ..........................................................................................................................125
5.17.7 Password...................................................................................................................... 125
5.17.8 System log....................................................................................................................126
5.17.9 Statistics .......................................................................................................................128
Appendix A: FAQ ..............................................................................................................................130
Appendix B: Configuring the PC .....................................................................................................134
Appendix C: Specifications..............................................................................................................138
Appendix D: Glossary....................................................................................................................... 139
IV

TL-WA7110ND 150Mbps High Power Wireless Access Point User Guide
Package Contents
The following items should be found in your package:
One TL-WA7110ND 150Mbps High Power Wireless Access Point
One power Adapter for TL-WA7110ND 150Mbps High Power Wireless Access Point
One Power Injector
Mounting Kits
Quick Installation Guide
One Resource CD for TL-WA7110ND 150Mbps High Power Wireless
Access Point, including:
This User Guide
Other helpful information
Note:
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact your distributor.
1

TL-WA7110ND 150Mbps High Power Wireless Access Point User Guide
Chapter 1. Introduction
1.1 Overview of the Product
The TL-WA7110ND 150Mbps High Power Wireless Access Point will allow you to connect your
network with other wireless devices wirelessly, sharing Internet Access, files and fun, easily and
securely. The high power design will also help you build a more stable link or cover more area
indoors.
The TL-WA7110ND 150Mbps High Power Wireless Access Point provides 7 operation modes for
multi-user to access the Internet: AP Client Router, AP Router, Access Point,
Multi-SSID, Repeater (Range Extender), Bridge with AP and Client. In AP Client Router mode,
it works as a WISP CPE and can access the Internet wirelessly via your WISP. In AP
Router mode, it can access the Internet via an ADSL/Cable Modem, while sharing data
wirelessly.
With the most attentive wireless security, the TL-WA7110ND 150Mbps High Power
Wireless Access Point provides multiple protection measures. It can be set to turn off
wireless network name (SSID) broadcast so that only stations that have the SSID
can be connected. The AP provides wireless LAN 64/128/152-bit WEP
encryption security, and WPA/WPA2 and WPA-PSK/WPA2-PSK authentication, as
well as TKIP/AES encryption security. It also supports VPN pass-through for sensitive data
secure transmission.
The TL-WA7110ND 150Mbps High Power Wireless Access Point complies with the IEEE 802.11n,
IEEE 802.11g and IEEE 802.11b standards so that the data transmission rate is up to 150Mbps.
The wireless transmission range can extend up to tens of kilometers.
1.2 Features
Complies with IEEE 802.11n, IEEE 802.11g, IEEE 802.11b, IEEE 802.3,
IEEE 802.3u standards.
Wireless Data transfer rates up to 150Mbps.
Supports AP Client Router, AP Router, Access Point, Multi-SSID, Repeater (Range Extender),
Bridge with AP and Client mode.
High output transmit power and receive sensitivity optimized.
Supports Client Router Mode for WISP CPE.
Supports passive power over Ethernet.
Supports Wireless Distribution System (WDS).
ACK timeout adjustment for long range transmission, up to 50km.
Provides throughput monitor indicating the current wireless throughput.
Supports Layer 2 User Isolation.
Supports Ping Watch Dog.
Supports link speed test.
Output transmit power adjustable.
Supports PPPoE, Dynamic IP, Static IP Internet Access.
Built-in NAT and DHCP server supporting static IP address distributing.
Provides WLAN ACL (Access Control List).

TL-WA7110ND 150Mbps High Power Wireless Access Point User Guide
Supports configuration backup/restore and firmware upgrade.
Supports Web management.
Supports Remote Management.
Supports UPnP, Dynamic DNS, Static Routing, VPN Pass-through.
Supports Virtual Server, Special Application and DMZ host.
Built-in firewall supporting IP address filtering, Domain Name filtering, and MAC
address filtering.
3

TL-WA7110ND 150Mbps High Power Wireless Access Point User Guide
1.3 Conventions
The AP or TL-WA7110ND, or device mentioned in this User guide stands for TL-
WA7110ND
150Mbps High Power Wireless Access Point without any explanations.
Parameters provided in the pictures are just references for setting up the product,
which may differ from the actual situation.
You can set the parameters according to your demand.
1.4 Panel Layout
1.4.1 The Front Panel
TL-WA7110ND consists of several LED indicators, which is designed to indicate connections and
wireless signal.
LED Explanation
Figure 1-1 Front Panel sketch
Name
Status
Indication
Off
No Power
On
Power on
Off
The device has a system error
On
The device is initialising
Flashing
The device is working properly
Off
There is no device linked to the corresponding port
On
There is a device linked to the corresponding port but no activity
Flashing
There is an active device linked to the corresponding port
Off
The Wireless function is disabled
Flashing
The Wireless function is enabled
Slow Flash
A wireless device is connecting to the network by function.
This process will last in the first 2 minutes.
On
A wireless device has been successfully added to the
network by function.
Quick Flash
A wireless device failed to be added to the network by function.
Table 2-1
4

TL-WA7110ND 150Mbps High Power Wireless Access Point User Guide
1.4.2 The Rear Panel
Figure 1-2 Rear Panel sketch
Viewed from left to right, the following parts are located on the rear panel of TL-WA7110ND.
POWER: The power port connects to the power adapter provided with the TL-WA7110ND.
MAIN (PoE): One LAN 10/100Mbps RJ45 port connects to a network device, such as a switch or
a router, and is capable of 12V Power over Ethernet output.
SECONDARY: This port is used as a secondary Ethernet port to connect to a network device,
such as a switch or a router.
WPS/RESET: This button is used for both WPS and Reset function. To use the WPS function,
press it for less than five seconds; to use the RESET function, press it for more than five seconds.
Used as RESET button:
There are two ways to reset to the Router's factory defaults:
1) Use the Factory Defaults function on System Tools -> Factory Defaults page in the
Router's Web-based Utility.
2) Use the WPS/RESET button: With the Router powered on, press
and hold the WPS/RESET button (more than 5 seconds) until the SYS LED
becomes quick-flash from slow-flash. Then release the button and wait the Access
Point to reboot to its factory default settings.
Used as WPS button:
If you have client devices, such as wireless adapters, that support Wi-Fi Protected Setup,
then you can press this button to quickly establish a connection between the Access Point
and client devices and automatically configure wireless security for your wireless network.
Wireless antenna: The external antenna is used to transmit and receive wireless data.
5

TL-WA7110ND 150Mbps High Power Wireless Access Point User Guide
Chapter 2. Connecting the Device
2.1 System Requirements
 Each PC in the LAN needs a working Ethernet Adapter and an Ethernet cable with RJ45
connectors.

TCP/IP protocol must be installed on each PC.
 Web browser, such as Microsoft Internet Explorer 5.0 or later, Netscape Navigator
6.0 or later.
 If the device is configured to AP Client Router mode, you also need:
Wireless Internet Service Provider (WISP).
 If the device is configured to AP Router mode, you also need:
Broadband Internet Access Service (DSL/Cable/Ethernet).

One DSL/Cable Modem that has an RJ45 connector (you do not need it if you connect the
router to the Ethernet.).
2.2 Installation Environment Requirements
 Operating temperature: -30℃~70℃
 Operating Humidity: 10%~90% RH, Non-condensing
2.3 Connecting the Device
To connect the AP, please follow the steps below:
1. Power off your PC, Cable/DSL Modem, and the AP.
2. Locate an optimum location for the AP. The best place is usually at the
center of your wireless network. The place must accord with the Installation Environment
Requirements.
3. Adjust the direction of the antenna. Normally, upright is a good direction.
After finishing the steps above, please choose the operation mode you need and carry out the
corresponding steps. There are seven operation mode supported by this AP: AP Client Router,
AP Router,Access Point,Multi-SSID,Repeater (Range Extender),Bridge with
AP and Client.
2.3.1 AP Client Router
Figure 2-1 Hardware Installation of the TL-WA7110ND in AP Client Router mode
6

TL-WA7110ND 150Mbps High Power Wireless Access Point User Guide
1. Connect the MAIN (PoE) port of TL-WA7110N to the POE port of the Power Injector with an
Ethernet cable.
2. Connect the PC to the LAN port of the Power Injector with an Ethernet cable.
3. Plug one end of the Power Adapter into the DC jack on the Power Injector, and the other end
in electrical wall socket.
4. Power on the PC(s) and notebook(s).
2.3.2 AP Router
Figure 2-2 Hardware Installation of the TL-WA7110ND in AP Router mode
1. Connect the MAIN (PoE) port of TL-WA7110N to the POE port of the Power Injector with an
Ethernet cable.
2. Connect the DSL/Cable Modem to the LAN port of the Power Injector with an Ethernet cable.
3. Plug one end of the Power Adapter into the DC jack on the Power Injector, and the other end
in electrical wall socket.
4. Power on the PC(s) and other connected devices (such as the ADSL modem).
Note:
In this mode, the LAN port of the Power Injector (connected to the LAN port of the Device) works
as the WAN port.
2.3.3 Access Point
This operation mode allows wireless stations to access.
Figure 2-3 Hardware Installation of the TL-WA7110ND in Access Point mode
1. Connect the MAIN (PoE) port of TL-WA7110N to the POE port of the Power Injector with an
Ethernet cable.
2. Connect the LAN port of the Power Injector to the wired network port with an Ethernet cable.
3. Plug one end of the Power Adapter into the DC jack on the Power Injector, and the other end
in the electrical wall socket.
4. Power on the notebook(s) and other connected devices (such as the Wired Router).
7

TL-WA7110ND 150Mbps High Power Wireless Access Point User Guide
2.3.4 Multi-SSID
In this mode, AP can support up to 4 SSID.
Figure 2-4 Hardware Installation of the TL-WA7110ND in Multi-SSID mode
1. Connect the MAIN (PoE) port of TL-WA7110N to the POE port of the Power Injector with an
Ethernet cable.
2. Connect the LAN port of the Power Injector to the wired network port with an Ethernet cable.
3. Plug one end of the Power Adapter into the DC jack on the Power Injector, and the other end
in the electrical wall socket.
4. Power on the notebooks and other connected devices (such as the Switch).
2.3.5 Repeater and Universal Repeater
Figure 2-5 Hardware Installation of the TL-WA7110ND in (Universal) Repeater mode
1. Connect the MAIN (PoE) port of TL-WA7110ND to the POE port of the Power Injector with an
Ethernet cable.
2. Plug one end of the Power Adapter into the DC jack on the Power Injector, and the other end
in electrical wall socket.
3. Power on the PC(s) and other connected devices (such as the Router).
Note:
Both Repeater and Universal Repeater modes allow the AP with its own BSS to relay data to a
root AP. The wireless repeater relays signal between its stations and the root AP
for greater wireless range. However, in Repeater mode, the WDS associated is enabled, while
in Universal Repeater mode, the WDS associated is disabled.
2.3.6 Bridge with AP
Two Devices are needed in this mode.
8

TL-WA7110ND 150Mbps High Power Wireless Access Point User Guide
Figure 2-6 Hardware Installation of the TL-WA7110ND in Standard AP -- Bridge mode
1. Connect the MAIN (PoE) port of TL-WA7110N to the POE port of the Power Injector with an
Ethernet cable.
2. Plug one end of the Power Adapter into the DC jack on the Power Injector, and the other end
in electrical wall socket.
3. Power on the PC(s).
Note:
It is recommended that you connect a PC/notebook to the LAN port of the Device with an Ethernet
cable, and then login the Device from the PC/notebook to set the Device in Bridge with AP mode.
2.3.7 Client
Figure 2-7 Hardware Installation of the TL-WA7110ND in Client mode
1. Connect the MAIN (PoE) port of TL-WA7110N to the POE port of the Power Injector with an
Ethernet cable.
2. Connect the PC to the LAN port of the Power Injector with an Ethernet cable.
3. Plug one end of the Power Adapter into the DC jack on the Power Injector, and the other end
in electrical wall socket.
4. Power on the PC(s) and other connected devices (such as the Router).
9

TL-WA7110ND 150Mbps High Power Wireless Access Point User Guide
Chapter 3. Quick Installation Guide
This Chapter will guide you to configure the AP to function in your network and gain access to the
internet through your ISP immediately after successful configuration. More detailed description of
the AP’s web-based utility and functions can be found in “Chapter 4 Configuring the AP”
3.1 Configure the Device
The instructions in this section will help you configure each of your PCs
to be able to communicate with the AP.
The default IP address of the TL-WA7110ND 150Mbps High Power Wireless Access
Point is
192.168.0.254. And the default Subnet Mask is 255.255.255.0. These values can be seen from
the LAN. They can be changed as you desire, as an example we use the
default values for description in this guide.
Connect the local PC to the LAN ports of the AP. There are then two ways to configure the IP
address for your PC.

Configure the IP address manually
1) Set up the TCP/IP Protocol for your PC. If you need instructions as to how to do this,
please refer to Appendix B: Configuring the PC.
2) Configure the network parameters. The IP address is 192.168.0.xxx ("xxx" is from 2 to
253), Subnet Mask is 255.255.255.0
Note:
If you configure your device by this way, please remember to change the configuration of your PC
to the figure as shown below to make your PC connect to the Internet successfully.
 Obtain an IP address automatically
This method can be available only when DHCP in section 4.8.1 is enabled.
1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC.
If you need instructions as to how to do this, please refer to Appendix B: Configuring the
PC.
10